1、 MS27621B 14 October 2009 SUPERSEDING MS27621A 29 September 2000 DETAIL SPECIFICATION SHEET ELBOW SUB ASSEMBLY, FLARED, 90, SWIVEL NUT This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shal
2、l consist of this specification sheet and MIL-DTL-83296. FIGURE 1. Elbow, 90, flared, sub assembly. AMSC N/A FSC 4730 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27621B 2 PIN Union Wire Nipple A inches (cm) B inches (cm) MS27621-4C M
3、S27624-4C MS27625-4C MS27627-4C .970 (2.46) .705 (1.79) MS27621-6C MS27624-6C MS27625-6C MS27627-6C 1.088 (2.76) .836 (2.12) MS27621-8C MS27624-8C MS27625-8C MS27627-8C 1.304 (3.31) .980 (2.48) MS27621-10C MS27624-10C MS27625-10C MS27627-10C 1.434 (3.64) 1.176 (2.98) NOTES: 1. Dimensions are in inch
4、es. 2. Metric equivalents are given for information only. 3. Dimensioning and tolerancing are in accordance with ASME Y14.5M. 4. Any design of adapter component to the left of plane A-A is acceptable provided that dimension A, provided the requirements specified herein and the requirements of MIL-DT
5、L-83296 are met. 5. Part or Identifying Number (PIN). FIGURE 1. Elbow, 90, flared, sub assembly - Continued. REQUIREMENTS: Dimensions and configurations: The design, construction, and physical dimensions shall be in accordance with MIL-DTL-83296 and figure 1, in case of conflict between this specifi
6、cation sheet and MIL-DTL-83296, this specification sheet shall govern. This part for use with MIL-DTL-83298 hose and hose assemblies in accordance with MIL-DTL-32330. Material: Material shall be corrosion resistant steel (CRES). Sizes -4 thru -8 shall have a forged design (tolerance .020 inch (0.51
7、mm). Size -10 shall have a bent tube design (tolerance .035 inch (0.89 mm). Finish: Finish shall be passivated as specified in MIL-DTL-83296. PIN example: MS27621 -4 C PIN example: MS27621-4C indicates a 90 elbow sub-assembly 1/4 inch, CRES. Material (C for CRES) Dash size (see figure 1) Specificati
8、on sheet number MS prefix Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27621B 3 Changes from previous issue. Marginal notations are not used in this revision to identify changes due to the extent of the changes Referenced documents. In addition
9、to MIL-DTL-83296, this document references the following: MIL-DTL-83298 MIL-DTL-32330 ASME Y14.5M SAE-AS4395 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AV DLA - CC Navy - AS Air Force - 99 (Project 4730-2008-039) DLA - CC Review activities: Navy - MC, SA Air Force - 71 NOTE: The acti
10、vities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
