1、MS27625C 14 October 2009 SUPERSEDING MS27625B 14 September 2005 DETAIL SPECIFICATION SHEET WIRE, RETAINER This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specificati
2、on sheet and MIL-DTL-83296. Part or Identifying Number (PIN) A .015 (0.38 ) inch (mm) B +.000 -.004 (+0.00 -0.10) inch (mm) C .010 (0.25) inch (mm) D inch (mm) E +.010 -.000 (+0.25 -.000 mm) F inch (mm) MS27625-4C 1.438 (36.53) .080 (2.030 .020 (0.51) .073 (1.85) .156 (3.96) .030 (0.76) MS27625-6C 1
3、735 (44.07) .095 (2.41) .023 (0.58) .087 (2.21) .186 (4.72) .037 (0.94) MS27625-8C 2.203 (55.96) .095 (2.41) .023 (0.58) .087 (2.21) .186 (4.72) .037 (0.94) MS27625-10C 2.625 (66.68) .125 (3.18) .031 (0.79) .115 (2.92) .246 (6.25) .050 .010 (1.27 0.25) FIGURE 1. Retainer wire dimensions and configu
4、ration. AMSC N/A FSC 4730INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27625C 2 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are for information only. 3. Unless otherwise specified all tolerances shall be .005 inch (0.13 m
5、m). 4. Wire shall be straight within .020 inch (0.51 mm) full indicator movement. 5. Unless otherwise specified radius shall be concentric to wire OD within .005 inch (0.13 mm) full indicator movement. 6. Unless otherwise specified radius or break all corners to .005 +.005/-.000 inch (0.13 + 0.13/-.
6、000 mm). 7. Radius shall be concentric to wire OD within .005 inch (0.13 mm) full indicator movement. 8. Surface roughness, as specified in ASME B46.1, shall not exceed 125 inches (3.18 m) nominal roughness average (Ra). FIGURE 1. Retainer wire dimensions and configuration - Continued. REQUIREMENTS:
7、 Dimensions and configurations shall be as specified on figure 1. This is a design specification sheet for manufacturing purposes. This specification sheet describes retainer wire used with MIL-DTL-83298 hose and MIL-DTL-32330 hose assemblies. Next assemblies are MS27620, MS27621, MS27633, and MS276
8、34. The item is only procured as an integral part of an adapter assembly. Material shall be a corrosion resistant steel (CRES), class 304 or 305, condition A in accordance with ASTM A313/A313M or ASTM A580/A580M. Finish: Retainer wire shall be passivated in accordance with SAE-AMS2700. Dry-film lubr
9、icant shall be in accordance with MIL-PRF-46010 or SAE-AS5272. PIN: MS27625 -4 C PIN example: MS27625-4C indicates a wire, retainer .080 inch diameter, CRES. Changes from previous issue. Marginal notations are not used in this revision to identify changes due to the extent of the changes. Specificat
10、ion sheet number Dash size (see figure 1) Material (C for CRES) MS prefix Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27625C 3 Referenced documents. In addition to MIL-DTL-83296, this document references the following: MIL-DTL-83298 MIL-DTL-323
11、30 MIL-PRF-46010 MS27620 MS27621 MS27633 MS27634 ASME B46.1 ASTM A313/A313M ASTM A580/A580M SAE-AMS2700 SAE-AS5272 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AV DLA - CC Navy - AS Air Force - 99 (Project 4730-2008-043) DLA - CC Review activities: Navy - MC, SA Air Force - 71 NOTE: Th
12、e activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
