1、AMSC N/A FSC 4820 MS29521G 7 April 2009 SUPERSEDING MS29521F 17 May 1984 DETAIL SPECIFICATION SHEET DISK, VALVE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this speci
2、fication sheet and MIL-V-7899, “Valves, Check, Aircraft Fuel System”. FIGURE 1. Disk, valve. INCH-POUND Inactive for new design after 15 October 1998. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS29521G 2 FIGURE 1. Disk, valve Continued.A diamet
3、er B maximum diameter C maximum radius D D/2 Dash number size Inch mm Inch mm Inch mm Inch mm Inch mm -12A .561 14.249 .933 23.698 .767 19.482 .860 21.844 .4300 10.9220-16 .792 20.117 1.183 30.048 .916 23.266 1.110 28.194 .5550 14.0970-20 1.024 26.010 1.527 38.786 1.097 27.864 1.248 31.699 .6240 15.
4、8496-24 1.248 31.699 1.777 45.136 1.200 30.48 1.240 31.496 .6200 15.7480-28 1.483 37.668 2.090 53.086 1.350 34.29 1.240 31.496 .6200 15.7480-32 1.719 43.663 2.277 57.836 1.451 36.855 1.382 35.103 .6910 17.5514-40 2.203 55.956 2.809 71.349 1.809 45.949 1.406 35.712 .7030 17.8562-48 2.703 68.656 3.309
5、 84.049 2.046 51.968 1.656 42.062 .8280 21.0312-56 3.213 81.610 3.996 101.498 2.395 60.833 2.093 53.162 1.0470 26.5938-64 3.711 94.259 4.496 114.198 2.667 67.742 2.313 58.750 1.1560 29.3624E F H (ref) J max K max Dash number size Inch mm Inch mm Inch mm Inch mm Inch mm -12A .440 11.176 .550 13.97 1.
6、086 27.584 .182 4.623-16 .525 13.335 .806 20.472 1.337 33.960 .198 5.029-20 .710 18.034 .940 23.876 1.704 43.282 .226 5.740-24 .845 21.463 .930 23.622 1.968 49.987 .236 5.994-28 1.025 26.035 .930 23.622 2.324 59.030 .249 6.325-32 1.100 27.94 1.078 27.381 2.511 63.780 .267 6.782-40 1.500 38.1 1.102 2
7、7.991 3.160 80.264 .287 7.290-48 1.703 43.256 1.352 34.341 3.735 94.869 .307 7.798-56 1.984 50.394 1.789 45.441 4.215 107.061 .327 8.306-64 2.234 56.744 .304 7.7222.009 51.029 4.715 119.761 .347 8.814Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS
8、29521G 3 NOTES: 1. Dimensions are in inches. Millimeters are given for general information only. 2. Tolerances for dimensions are as shown in the table below: 3. Referenced documents shall be of the issue in effect on date of invitation for bid. 4. For design features, this standard takes precedence
9、 over procurement documents referenced herein. FIGURE 1. Disk, valve Continued. L max M diameter N minimum radius R max Rated flow Tubing size Dash number size Inch mm Inch mm Inch mm Inch mm GPM Inch mm -12A .282 7.163 15 .75 19.05-16 .335 8.509 30 1. 25.4-20 .373 9.474 50 1.25 31.75-24 .382 9.703
10、.156 3.962 70 1.50 38.1-28 .395 10.033 100 1.75 44.45-32 .470 11.938 130 2. 50.8-40 .500 12.7 215 2.50 63.5-48 .531 13.488 320 3.3 83.82-56 .563 14.300 450 3.50 88.9-64 .594 15.088 .1495 3.7973 .152 3.861 .219 5.562 600 4. 101.6tolerance tolerance Decimal Places Inch mm .XXX .005 0.127 .XXXX .0025 0
11、.0635 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS29521G 4 REQUIREMENTS Intended use. These swing check, fuel valve elements are suitable for use with hydrocarbon fuels, fuel vapors, and air and may be used in check valves MS21430, MS28882, and
12、 MS28884. Requirements. The valve element, when mounted to a test fixture and discharging into an open tank, shall achieve the following performance: (1) Opening and closing pressure per MIL-V-7899. (2) Pressure drop at rated flow shall be less than 45 inches water. (3) Leakage: -32 and smaller 0.5
13、cc per minute (max). -40 and larger sizes 1.0 cc per minute (max). Materials. Materials shall comply to requirements listed in the procurement specification, MIL-V-7899. Finish. Finish shall comply to requirements listed in the procurement specification, MIL-V-7899. Qualification. Disk, valves furni
14、shed under this specification sheet shall be products which are qualified for listing on Qualified Products List, QPL-7899. An online listing of products qualified to this specification may be found in the Qualified Products Database (QPD) at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.da
15、ps.dla.mil . Marking. (1) Color identification: The component shall be color coded to indicate fuel use by means of a red color per MIL-F-8615, “Fuel System Components: General Specification For”. (2) Assembly date mark: The valve assembly shall be date marked, packaged, and stored per, SAE ARP5316
16、, “Storage of Elastomer Seals and Seal Assemblies Which Include an Elastomer Element Prior to Hardware Assembly”. Valve characteristic: See figure 1. Part or Identifying Number (PIN). The PIN is as follows: MS29521 - 12A Dash number Specification sheet number Provided by IHSNot for ResaleNo reproduc
17、tion or networking permitted without license from IHS-,-,-MS29521G 5 Reference documents. This document references the following: MIL-F-8615, “Fuel System Components: General Specification For”. MIL-V-7899, “Valves, Check, Aircraft Fuel System”. MS21430, “Valve, Check, Fuel and Air, Poppet Type, Zer
18、o, Leak”. MS28882, “Valve, Fuel Check, Low Pressure, Gasket Seal Straight Thread Connection”. MS28884, “Valve, Fuel Check, Low Pressure, Flared Tube Connection”. SAE ARP5316, “Storage of Elastomer Seals and Seal Assemblies Which Include an Elastomer Element Prior to Hardware Assembly”. Changes from
19、previous issue: Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodians: Preparing activity: Army AV DLA - CC Navy AS Air Force - 99 DLA - CC (Project 4820-2009-020) Reviewer activities: Air Force 71 Navy SA
20、 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
