1、 AMSC N/A FSC 5940 INCH-POUND MS35430C 15 December 2003 SUPERSEDING MS35430B 10 February 1961 DETAIL SPECIFICATION SHEET TERMINAL, LUG, SOLDER TYPE, COPPER STAMPING, ONE HOLE Inactive for new design after 18 October 2000. This specification sheet is approved for use by all departments and agencies o
2、f the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-15659. FEHBDCAFIGURE 1. Terminal dimensions for -1 through -13 and -27. FIGURE 2. Optional wire grip designs (see note 4). Provided by IHSNot for ResaleNo re
3、production or networking permitted without license from IHS-,-,-MS35430C 2 TABLE I. Dash numbers and dimensions for -1 through -13 and -27. A Dash no. Wire size AWG1nominal Stud size Min. Max. B C D 3/64 E 3/64 F 1/32 H 0.003 1 9/64 29/64 3/32 17/64 0.016 2 2 0.089 0.096 3 4 0.115 0.127 0.020 4 6 0.
4、141 0.153 5 8 0.167 0.179 6 14-20 10 0.193 0.205 5/64 9/32 5/32 0.032 7 4 0.115 0.127 0.020 8 6 0.141 0.153 9 8 0.167 0.179 10 10-12 10 0.193 0.205 5/32 3/16 11 6 0.141 0.153 0.032 12 8 0.167 0.179 13 6-8 10 0.193 0.205 3/16 5/16 9/16 5/16 25/64 0.040 27 14-20 6 0.141 0.153 1/16 1/4 1/2 5/32 5/16 0.
5、032 1American Wire Gauge. BHEKFDACGFIGURE 3. Terminal dimensions for -14 and -16 through -18. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS35430C 3 TABLE II. Dash numbers and dimensions for -14 and -16 through -18. A Dash no. Wire size AWG1nomin
6、al Stud size Min. Max. B C D E F G H 0.003 K 14 - 6 0.141 0.153 5/16 1 3/32 - 19/32 11/32 - 1/4 16 3/4 7/16 1/4 3/16 17 1 3/16 5/8 5/16 18 10 10 0.193 0.205 1/8 3/8 1 1/4 3/16 3/4 3/8 0.032 1/4 1American Wire Gauge. FIGURE 4. Terminal dimensions for -15 and -19 through -23. TABLE III. Dash numbers a
7、nd dimensions for -15 and -19 through -23. A Dash no. Wire size AWG1nominal Stud size Min. Max. B C D E F G H 0.003 15 10 10 0.193 0.205 1/8 5/16 19/32 3/16 - 5/32 0.032 19 1/4 0.258 0.285 9/16 20 5/16 0.320 0.347 21 1-2 3/8 0.383 0.410 13/3211/161 19/32 25/32 31/32 11/32 22 5/16 0.320 0.347 23 0-00
8、 3/8 0.383 0.410 1/2 3/4 1 11/16 53/64 1 3/8 0.091 1American Wire Gauge. H B EFD332RadGA C Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS35430C 4 CHBEFDAFIGURE 5. Terminal dimensions for -24 through -26. TABLE IV. Dash numbers and dimensions for
9、-24 through -26. A Dash no. wire size AWG1nominal Stud size Min. Max. B C D E F H 0.003 24 4 0.115 0.127 9/32 1 1/8 53/64 25 13/16 15/32 26 10 10 0.193 0.205 1/8 3/8 1 1/8 3/16 13/16 0.032 1American Wire Gauge. REQUIREMENTS: 1. Material: Electrolytic copper strip or sheet alloy C11000, temper O60 in
10、 accordance with ASTM B 152/B 152M (DoD adopted). 2. Finish: Tinned; electrodeposited over entire surface in accordance with ASTM B 545 (DoD adopted). Minimum thickness 0.0005 inches all over. NOTES: 1. Dimensions are in inches. 2. Unless otherwise specified, tolerance is 1/64. 3. Remove all burrs.
11、4. Figure 2 optional wire grip design is for -1 through -13 and -27 only. 5. Referenced documents of issue in effect on date of invitation for bids shall apply. 6. In the event of a conflict between the text of this document and the references cited herein, the text of this document shall take prefe
12、rence. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS35430C 5 7. The part or identifying number (PIN) consists of the letters MS, the specification sheet number, and a dash number taken from table I, II, III, or IV. MS 35430 - 10 CHANGES FROM PRE
13、VIOUS ISSUE: Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodians: Preparing Activity: Army - MI Navy - SH Air Force - 99 DLA - GS2 (Project 5940-1445) Dash number Specification sheet number MS prefix Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
