1、 AMSC N/A FSC 4730 MS35758D 30 August 2012 SUPERSEDING MS35758C 23 January 2008 DETAIL SPECIFICATION SHEET CUPS, GREASE, MANUAL FEED This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for this product described herein shall consist o
2、f this specification sheet and MIL-C-1213. Dash numbers Grease capacity ounce A Thread B max OD inch (mm) C max Overall length inch (mm) Steel Brass Uncoated Plated Uncoated -1 -4 -7 .25 .125 -27 NPT 1.125 (28.58) 1.625 (41.28) -2 -5 -8 .50 .125 -27 NPT 1.250 (31.75) 1.875 (47.63) -3 -6 -9 1.0 .250
3、18 NPT 1.875 (47.63) 2.500 (63.50) - - -10 2.0 .375 -18 NPT 2.250 (57.15) 2.875 (73.03) - - -11 3.5 .500 -14 NPT 2.750 (69.85) 1.250 (31.75) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, the tolerance for 3 place decimals is
4、 .005 inch (0.13 mm). 4. Threads shall be in accordance with FED-STD-H28/7, FED-STD-H28/8, ASME B1.20.1 and ASME B1.20.3. 5. The illustration is for identification only and is not intended to restrict design or shapes not dimensioned. FIGURE 1. Cups, grease, manual feed. LEATHER WASHER METAL WASHER
5、A C B C B A LEATHER WASHER METAL WASHER INCH-POUND OPTIONAL DESIGN (WITHOUT RATCHET) Inactive for new design after 5 April 1999. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS35758D 2 REQUIREMENTS: Manual feed grease cups shall be specified on fi
6、gure 1 and tables I and II. Materials shall be, specified in table I. TABLE I. Materials. Code Material Form Specification Alloy B B Brass Bars ASTM B16/B16M ASTM B36/B36M ASTM B121/B121M ASTM B124/B124M 260, 268, or 360 Castings ASTM B61 ASTM B62 ASTM B148 ASTM B176 ASTM B271 ASTM B369 ASTM B427 AS
7、TM B505/B505M ASTM B584 ASTM B763 ASTM B770 ASTM B806 SAE AMS4842 SAE AMS4845 SAE AMS4855 SAE AMS4860 SAE AMS4862 SAE AMS4890 As applicable C Low carbon steel Bars and forgings SAE-AIR4127 In accordance with, any standard composition. S Stainless Steel (CRES) N/A SAE AMS5659, SAE AMS5862 or alloy 15
8、5 PH, ASTM A564/A564M type XM-12 or UNS S15500 or SAE AMS5665 As applicable Spring materials. Spring for steel cup shall be steel in accordance with ASTM A229/A229M or ASTM A227/A227M, class 2. Spring for brass cup shall be brass in accordance with ASTM B159/B159M. Leather washer. The leather shall
9、 be made from cattle hides. The leather shall be tanned with chromium salts (mineral-tanned) without the use of vegetable tanning materials. No degreasing shall be employed after the normal tanning process. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS
10、MS35758D 3 Leather shall be treated with a fungicidal agent in accordance with MIL-DTL-32068 to render the material fungus-resistant. Plating finish designators for dash -4, -5, and -6 only shall be in accordance with table II. TABLE II. Plating finish identification codes. 1/ PIN code plating
11、finish Material Plating finish C Steel Cadmium plating in accordance with SAE AMS-C-81562, type II, class 3 or SAE-AMS-QQ-P-416, type II, class 2, 2/ F Steel NAVAIR trivalent chromium pretreatment (TCP) in accordance with MIL-DTL-5541, type II, class 1a. H Steel Zinc phosphate finish in accordance w
12、ith MIL-DTL-16232 type Z, class1. 3/ J Steel Zinc plating in accordance with ASTM B633; type II or III, Fe/Zn 5, or ASTM B695, type II, class 5 N Steel Zinc plating in accordance with ASTM B633, type VI, Fe/Zn 5, P Steel Aluminum-nickel in accordance with ASTM F1136/F1136M, grade 3, NC. V Steel Zinc
13、nickel in accordance with SAE AMS2417, type 1 S CRES Passivate in accordance with SAE AMS2700, type 6 or 7. 4/ 1/ Finished product shall be shall be capable of withstanding minimum of 96 hours salt spray. 2/ Embitterment test need not be run. 3/ Hexavalent chromium free. 4/ If finish code is the sa
14、me as material code, then omit finish code. Trivalent wrenchability. This term is used to evaluate the ability of the finish to withstand abrasion from excessive amount of wrenching. Where wrenchability is poor, the need to touch-up the finish is needed. Brush plating of hard chromium by electrodepo
15、sition shall be in accordance with SAE AMS2451/5 and brush plating of medium-hardness, low stress nickel by electrodeposition shall be in accordance with SAE AMS2451/9. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS35758D 4 Part or Identifying Nu
16、mber (PIN): (The PIN covers the complete item with nuts and sleeves.) MS 35758 -6 S N Finish code (see table II) Material code (see table I) Size dash no. (see table I) Specification sheet number MS prefix Guidance on the use of Alternative Plating that is less hazardous or nonhazardous on environme
17、nt. This specification provides for a number of alternative plating materials via the PIN. Users should select the PIN with the least hazardous material that meets the form, fit and function requirements of their application. Changes from previous issue. The margins of this standard are marked with
18、vertical lines to indicate modifications generated by this change. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire c
19、ontent irrespective of the marginal notations. Referenced documents. In addition to MIL-C-1213, this document references the following: FED-STD-H28/7 FED-STD-H28/8 MIL-DTL-5541 MIL-DTL-16232 MIL-DTL-32068 ASTM A564/A564M ASME B1.20.1 ASME B1.20.3 ASTM B16/B16M ASTM B36/B36M ASTM B121/B121M ASTM B124
20、/B124M ASTM A229/A229M ASTM B61 ASTM B62 ASTM B148 ASTM B159/B159M ASTM B176 ASTM A227/A227M ASTM B271 ASTM B369 ASTM B427 ASTM B505/B505M ASTM B584 ASTM B633 ASTM B695 ASTM B763 ASTM B770 ASTM B806 ASTM F1136/F1136M SAE AIR4127 SAE AMS-C-81562 SAE-AMS-QQ-P-416 SAE AMS2417 SAE AMS2700 SAE AMS4842 SA
21、E AMS4845 SAE AMS4855 SAE AMS4860 SAE AMS4862 SAE AMS4890 SAE AMS5659 SAE AMS5665 SAE AMS5862 SAE AMS2451/5 SAE AMS2451/9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS35758D 5 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AR DLA-CC
22、Navy - SH Air Force - 99 DLA - CC (Project 4730-2012-034) Review activities: Army - AT Navy AS, MC Air Force - 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
