1、AMSC N/A FSC 4730 MS39206G 30 August 2012 SUPERSEDING MS39206F 01 February 2002 DETAIL SPECIFICATION SHEET ADAPTERS, STRAIGHT, PIPE TO TUBE - SAFETY SLEEVE COMPRESSION TYPE, MALE PIPE END This specification is approved for use by all Departments and Agencies of the Department of Defense. The require
2、ments for acquiring the product described herein shall consist of this specification sheet. Inactive for new design after 29 December 1967. INCH-POUND FIGURE 1. Adapters, straight, pipe to tube-safety sleeve compression type, male pipe end. Provided by IHSNot for ResaleNo reproduction or networking
3、permitted without license from IHS-,-,-MS39206G 2 TABLE I. Adapters, straight, pipe to tube-safety sleeve compression type, male pipe end. 1/ 2/ Dash No. Tube O.D. A Pipe Thread NPTF B C Thread Length D E F G H J 1 1/8 1/8 5/16 24UNF-2A 7/32 3/32 .135 .139 13/64 1/8 9/32 3/16 2 3/16 1/8 3/8 24UNF-2A
4、 7/32 1/8 .196 .200 1/4 5/32 9/32 3/16 3 1/4 1/8 1/2 20UNF-2A 21/64 13/64 .261 .265 19/64 13/64 13/32 3/16 4 5/16 1/8 9/16 18UNF-2A 21/64 13/64 .324 .328 19/64 13/64 13/32 3/16 5 1/4 1/4 1/2 20UNF-2A 21/64 13/64 .261 .265 19/64 13/64 13/32 13/64 6 5/16 1/4 9/16 18UNF-2A 21/64 13/64 .324 .328 19/64 1
5、3/64 13/32 13/64 7 3/8 1/4 5/8 18UNF-2A 23/64 9/32 .386 .390 19/64 13/64 7/16 9/32 8 1/2 1/4 3/4 16UNF-2A 11/32 27/64 .514 .518 5/16 13/64 7/16 9/32 9 1/2 3/8 3/4 16UNF-2A 11/32 27/64 .514 .518 5/16 13/64 7/16 27/64 10 5/8 3/8 15/16 16UN-2A 23/64 1/2 .641 .645 11/32 15/64 15/32 13/32 11 3/8 1/2 5/8
6、18UNF-2A 23/64 9/32 .386 .390 19/64 13/64 7/16 1/2 12 5/8 1/2 15/16 16UN-2A 23/64 1/2 .641 .645 11/32 15/64 15/32 1/2 13 3/4 1/2 1-1/16 16UN-2A 23/64 21/32 .766 .770 11/32 13/64 15/32 1/2 14 3/4 3/4 1-1/16 16UN-2A 23/64 21/32 .766 .770 11/32 13/64 15/32 21/32 15 7/8 3/4 1-3/16 16UN-2A 23/64 23/32 .8
7、91 .895 11/32 13/64 15/32 21/32 16 1 3/4 1-5/16 16.UN-2A 23/64 7/8 1.016 1.020 13/32 13/64 15/32 21/32 17 7/8 1 1-3/16 16UN-2A 23/64 23/32 .891 .895 11/32 13/64 15/32 23/32 18 1 1 1-5/16 16UN-2A 23/64 7/8 1.016 1.020 13/32 13/64 15/32 7/8 19 1-1/4 1 1-5/8 16UN-2A 7/16 1-3/32 1.270 1.274 13/32 13/64
8、35/64 29/32 20 1-1/4 1-1/4 1-5/8 16UN-2A 7/16 1-3/32 1.270 1.274 13/32 13/64 35/64 1-3/32 21 1-1/2 1-1/2 1-7/8 16UN-2A 15/32 1-11/32 1.520 1.524 31/64 13/64 35/64 1-11/32 See notes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39
9、206G 3 TABLE I. Adapters, straight, pipe to tube-safety sleeve compression type, male pipe end. Continued. 1/ 2/ K L M 7/16 7/8 1-3/16 7/16 7/8 1-7/32 1/2 1 1-13/32 5/8 1 1-3/8 5/8 1-5/32 1-9/16 5/8 1-1/4 1-5/8 11/16 1-1/4 1-11/16 3/4 1-1/4 1-25/32 3/4 1-1/4 1-25/32 15/16 1-11/32 1-7/8 7/8 1-19/32 2
10、1/32 15/16 1-5/8 2-5/32 1-1/8 1-39/64 2-13/64 1-1/8 1-5/8 2-7/32 1-1/4 1-5/8 2-7/32 1-3/8 1-5/8 2-7/32 1-3/8 1-13/16 2-13/32 1-3/8 1-13/16 2-13/32 1-5/8 1-7/8 2-9/16 1-11/32 1-29/32 2-17/32 2 2 2-11/16 1/ Dimensions are in inches. 2/ This illustration is for identification and is not intended to re
11、strict designs or shapes not dimensioned. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39206G 4 REQUIREMENTS: Dimensions and configuration: See figure 1. Tolerances: Unless otherwise specified, decimals .005, fractions 1/64, degrees 2. Threads:
12、The threads shall be in accordance with FED-STD-H28. Adapters: See table I. Material: Code Material C Steel bar, type AISI-C-1112, C-1113, C-1117, C-1118 or C-1137 in accordance with SAE AIR4127. F Alloy steel in accordance SAE AIR4127. S Corrosion resistant steel in accordance with SAE AMS5659, SAE
13、 AMS5862, or, alloy 15-5 PH in accordance with ASTM A564/A564M type XM-12 or UNS S15500 or SAE AMS5665. Chemical finish: Code Finish C Carbon steel: Cadmium in accordance with SAE AMS-QQ-P-416, type II, class 3, 200 inches to 300 inches (5.08 m to 7.62 m) thick. F Alloy Steel: Cadmium in accordance
14、with SAE AMS-QQ-P-416, type II, class 3, 200 inches to 300 inches (5.08 m to 7.62 m) thick. S Corrosion resistant steel: Passivate in accordance with SAE AMS2700, type 6 or 7. Z Steel, alternative chem finish: ASTM B633, type VI, FeZn 25. Part or Identifying Number (PIN) example: (PIN covers the com
15、plete item with nuts and sleeves.) MS 27612 -8 C Z If finish code same as Material code, then use only one code. Material code Dash size Specification number MS prefix Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39206G 5 Guidance on use of alte
16、rnative parts with less hazardous or non-hazardous materials. This specification provides an alternate material, corrosion resistant steel, and Zinc finish via the PIN. Users should select the PIN with the least hazardous material that meets the form, fit, and function requirements of their applicat
17、ion. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and
18、contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. This document references the following: FED-STD-H28 ASTM A564/A564M ASTM B633 SAE AIR4127 SAE
19、AMS5659 MS39210 SAE AMS5665 SAE AMS5862 SAE AMS2700 SAE AMS-QQ-P-416 MS39212 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy-AS Air Force-99 DLA - CC (Project 4730-2012-039) Review activities: Navy-MC,SA,SH Air Force-71 NOTE: The activities listed above were interested in
20、 this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
