1、 AMSC N/A FSC 5935 MS75021E 5 September 2013 SUPERSEDING MS75021D 23 December 1974 DETAIL SPECIFICATION SHEET CONNECTOR, RECEPTACLE, ELECTRICAL, - 12 CONTACT, INTERVEHICULAR, 28 VOLT, WATERPROOF This specification is approved for use by all Departments and Agencies of the Department of Defense. The
2、requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-38159. Inches mm Inches mm .016 0.41 .269 6.83 .043 1.09 .667 16.94 .047 1.19 .743 18.87 .061 1.55 .804 20.42 .065 1.65 1.596 40.54 .125 3.18 2.183 55.45 .142 3.61 2.680 68.07 FIGURE 1. Conn
3、ector, plug, electrical, intervehicular. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS75021E 2 Termination designation Circuit number Connects to A 24-484 LH blackout marker B 22-461 LH service signal C 24-483 RH blackout marker D 90
4、Ground E 21-489 Service clearance F 23 Blackout stop H 490 Blackout clearance J 22-460 RH service signal K 37 Auxiliary power L 90 Ground M 53 Brake N 53 Brake NOTES: 1. Dimension are in inches, metric equivalents are given for information only. 2. Circuit numbers are in accordance with typical wiri
5、ng diagram Army drawing number 8377310. 3. Threads shall be in accordance with FED-STD-H28. 4. Details of this assembly shall be in accordance with drawings referenced herein and may be obtained online from www.tacom.army.mil or from US Army Tank Automotive Command, 6501 E. 11 Mile Rd. Warren, MI 48
6、397-5000. 5. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements and promotes economically advantageous life cycle. 6. International standardization agreeme
7、nt implementation. This specification implements QSTAG 327 and STANAG 4007. When amendment, revision, or cancellation of this specification is proposed, the preparing activity must coordinate the action with the U.S. National Point of Contact for the international standardization agreement, as ident
8、ified in the ASSIST database at http:/assist.dla.mil/. FIGURE 1. Connector, plug, electrical, intervehicular - Continued. Requirements: Mating receptacle: These plugs mate with receptacles specified in MS75020. This drawing illustrates final assembly. The parts to be shipped unassembled in bag. Elec
9、trical requirements shall be in accordance with Army drawing 10911317. Marking shall consist of the MS Part or Identifying Number (PIN) and manufacturer identification in accordance with MIL-STD-130. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS
10、75021E 3 PIN: See table I. TABLE I. PIN information. PIN Type Body assembly Army PIN Insert Army PIN Contact Army PIN MS75021-1 Pin 8724316 8701274 7716521 MS75021-2 Socket 8701275 7716520 Changes from previous issues. Marginal notations are not used in this revision to identify changes with respect
11、 to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-38159 this document references the following: MS75020 MIL-STD-130 FED-STD-H28 Army drawing 10911317 Army drawing 8377310 QSTAG 327 STANAG 4007 CONCLUDING MATERIAL Custodians: Preparing activity: Arm
12、y AT DLA - CC DLA - CC (Project 5935-2012-242) Review activities: Army CR, CR4, MI Navy MC, SH Air force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
