1、 DETAIL SPECIFICATION SHEET INSERT ARRANGEMENTS, ELECTRICAL CONNECTOR, SIZE 32, CLASS L, 60 AMPS This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet
2、and MIL-DTL-22992. Quantity Contact Size Socket SAE-AS39029/49 M39029- Pin SAE-AS39029/48 M39029- 1 A 4 331 320 1 N 4N 331 (see note 6) 321 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. Unless otherwise specified, tolerance is .002 (.05 mm). 2. Unless otherwi
3、se specified, front face of pin insert pattern is shown. Socket inserts are the reverse. 3. -02-Cable IPCEA 2-NO 6 conductor round, type W. 4. -03-Cable-C0-02-HDF (2/4) 1100 in accordance with MIL-DTL-3432. 5. Mark 32-02 on 32-03 insert. Trademark and 32-( ) shall appear in available space. Contact
4、identifying letter shall be located so as to identify relative contact. 6. Only the pin contact is lengthened and has the N (neutral) designation. The mating socket contact is the same as the power contact. FIGURE 1. 28 volt DC two wire, -02 and -03 insert arrangements, service D. AMSC N/A FSC 5935
5、MS90565J 8 May 2013 SUPERSEDING MS90565H 26 October 2005 INCH-POUND INSERT INDEX Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS90565J 2 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. Unless otherwise specif
6、ied, tolerance is .002 (.05 mm). 2. Unless otherwise specified, front face of pin insert pattern is shown. Socket inserts are the reverse. 3. -04-Cable IPCEA 2-NO 6 conductor round, type G. 4. -05-Cable-C0-02-HDF (2/6-2/8R) 1100 in accordance with MIL-DTL-3432 5. Mark 32-04 on 32-05 insert. Trademar
7、k and 32-( ) shall appear in available space. Contact identifying letter shall be located so as to identify relative contact. 6. Only the pin contact is lengthened and has the N (neutral) designation. The mating socket contact is the same as the power contact. FIGURE 2. 28 volt AC single phase two w
8、ire grounding, -04 and -05 insert arrangements, service D. Quantity Contact Size Socket SAE-AS39029/49 M39029- Pin SAE-AS39029/48 M39029- 1 A 4 331 320 1 N 4N 331 (see note 6) 321 2 G1, G2 6N 329 (see note 6) 318 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr
9、om IHS-,-,-MS90565J 3 Quantity Contact Size Socket SAE-AS39029/49 M39029- Pin SAE-AS39029/48 M39029- 2 A, B 4 331 320 2 N, G 4N 331 (see note 6) 321 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. Unless otherwise specified, tolerance is .002 (.05 mm). 2. Unles
10、s otherwise specified, front face of pin insert pattern is shown. Socket inserts are the reverse. 3. -06-Cable IPCEA 3-NO 6 conductor round, type G. 4. -07-Cable-C0-03-HDF (3/4-3/10R) 1210 in accordance with MIL-DTL-3432. 5. Mark 32-06 on 32-07 insert. Trademark and 32-( ) shall appear in available
11、space. Contact identifying letter shall be located so as to identify relative contact. 6. Only the pin contact is lengthened and has the N (neutral) designation. The mating socket contact is the same as the power contact. FIGURE 3. 28 volt AC single phase three wire grounding, -06 and -07 insert arr
12、angements, service D. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS90565J 4 Quantity Contact Size Socket SAE-AS39029/49 M39029- Pin SAE-AS39029/48 M39029- 3 A, B, C 4 331 320 1 N 4N 331 (see note 6) 321 1 G 6N 329 (see note 6) 318 NOTES: 1. Dime
13、nsions are in inches. Metric equivalents are given for information only. Unless otherwise specified, tolerance is .002 (.05 mm). 2. Unless otherwise specified, front face of pin insert pattern is shown. Socket inserts are the reverse. 3. -12-Cable IPCEA 43-NO 6 conductor round, type G. 4. -13-Cable-
14、C0-04-HDF (4/4-4/12R) 1290 in accordance with MIL-DTL-3432. 5. Mark 32-12 on 32-13 insert. Trademark and 32-( ) shall appear in available space. Contact identifying letter shall be located so as to identify relative contact. 6. Only the pin contact is lengthened and has the N (neutral) designation.
15、The mating socket contact is the same as the power contact. FIGURE 4. 28 volt AC three phase four wire grounding, -12 and -13 insert arrangements, service D. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS90565J 5 Insert rotation (degrees from nor
16、mal) Arrangement number Normal DC or 60 Hz (see figures 6 through 9) Alternate (see figures 6 through 9) 400 Hz W X Y 32 02 32 03 0 - - - 32 04 32 05 0 - 90 - 32 06 32 07 0 - - - 32 12 32 13 0 - - 180 FIGURE 5. Insert arrangements and rotations. Provided by IHSNot for ResaleNo reproduction or networ
17、king permitted without license from IHS-,-,-MS90565J 6 NOTES: 1. REF. MS90555*S. 2. REF. MS90557*S. 3. Front face of socket insert shown. FIGURE 6. Socket contact pattern and polarization, Insert in normal position (60 Hz power only). Provided by IHSNot for ResaleNo reproduction or networking permit
18、ted without license from IHS-,-,-MS90565J 7 NOTES: 1. REF. MS90555*SX. 2. REF. MS90557*SX. 3. Front face of socket insert shown. FIGURE 7. Socket contact pattern and polarization, Insert in alternate position (400 Hz power only). Provided by IHSNot for ResaleNo reproduction or networking permitted w
19、ithout license from IHS-,-,-MS90565J 8 NOTES: 1. REF. MS90556*P. 2. REF. MS90558*P. 3. Front face of pin insert shown. FIGURE 8. Socket contact pattern and polarization, insert in normal position (60 Hz power only). Provided by IHSNot for ResaleNo reproduction or networking permitted without license
20、 from IHS-,-,-MS90565J 9 NOTES: 1. REF. MS90556*PX. 2. REF. MS90558*PX. 3. Front face of pin insert shown. FIGURE 9. Socket contact pattern and polarization, insert in alternate position (400 Hz power only). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH
21、S-,-,-MS90565J 10 REQUIREMENTS: Design and construction, see figures 1 through 9, and table I. Neutral pin (N) is not connected to shell. Grounding pin (G) is connected to shell. Applicable SAE-AS39029/112 crimp bushings shall be supplied with the contacts for insert arrangements as specified. TABLE
22、 I. Accessories. Insert arrangement Contacts Cable conductors MS90556 & MS90557 1/ Contact bushings required (in accordance with SAE-AS39029/112) Quantity Size Quantity Size Quantity PIN MS3348- 32 02 2 4 2 6 2 4-6L 32 04 2 2 4 6 2 2 6 10(G) 2 2 4-6L 6-10L 32 05 2 2 4 6 2 2 4 8(G) - 2 - 6-8L 32 06 3
23、 1 4 4 3 3 6 12(G) 3 1 4-6L 4-8L 32 12 4 1 4 6 4 4 6 12G 4 - 4-6L - 1/ (G) Designates grounding. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Gove
24、rnment assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In
25、 addition to MIL-DTL-22992, this document references the following: MIL-DTL-3432 MS90556 MS90557 SAE-AS39029/48 SAE-AS39029/49 SAE-AS39029/112 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS90565J 11 CONCLUDING MATERIAL Custodians: Preparing activ
26、ity: Army CR DLA CC Navy EC Air Force 85 DLA CC Review activities: (Project 59352013-094) Army AT, AV, CR4, MI Navy AS, CG, MC, SH, YD Air Force 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
