1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device types 05, 06, 07, and 08. Add case outline C. Make changes to 1.2.2, 1.3, table I, and figure 1. - ro 00-09-28 R. MONNIN B Drawing updated to reflect current requirements. - gt 02-04-24 R. MONNIN C Make change to the VICRtest and CMRR
2、test conditions as specified in table I. - ro 02-10-03 R. MONNIN D Five year review requirement. - ro 07-10-02 R. HEBER E Make corrections to JCand JAlimits for all case outlines under paragraph 1.3. Make correction to case outline H terminal symbols for device types 05 and 06 under figure 1. Update
3、 paragraphs to current MIL-PRF-38535 requirements. Delete references to device class M requirements. - ro 13-03-06 C. SAFFLE REV SHEET REV SHEET REV STATUS REV E E E E E E E E E E E E E OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY RAJESH PITHADIA DLA LAND AND MARITIME COLUMBUS,
4、 OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY RAJESH PITHADIA APPROVED BY RAYMOND MONNIN MICROCIRCUIT, LINEAR, BICMOS, LOW POWER, RAIL-TO-RAIL INPUT/OUTPUT, OP
5、ERATIONAL AMPLIFIER, MONOLITHIC SILICON DRAWING APPROVAL DATE 00-06-23 AMSC N/A REVISION LEVEL E SIZE A CAGE CODE 67268 5962-00512 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E212-13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT
6、DRAWING SIZE A 5962-00512 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device class Q) and space application (device class V). A choice of c
7、ase outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 00512 01 Q H A Federal stock class desi
8、gnator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the approp
9、riate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 TLV2460M Single operational amplifier with Shutdown 02 TLV2460AM Single operational amplifier with Shutdown 0
10、3 TLV2461M Single operational amplifier without Shutdown 04 TLV2461AM Single operational amplifier without Shutdown 05 TLV2462M Dual operational amplifier without Shutdown 06 TLV2462AM Dual operational amplifier without Shutdown 07 TLV2463M Dual operational amplifier with Shutdown 08 TLV2463AM Dual
11、operational amplifier with Shutdown 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case
12、 outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line H GDFP1-F10 or CDFP2-F10 10 Flat pack P GDIP1-T8 or CDIP2-T8 8 Dual-in-line 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead fini
13、sh. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00512 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 3
14、DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ Supply voltage range (VDD) 6 V Differential input voltage (VID) . VDD 0.2 V to VDD+ 0.2 V Input current, (IIN) (any input) . +200 mA Output current, (IOUT) . +175 mA Total input current, (II)(into +VDD) . 175 mA Total output current, (Io) (ou
15、t of GND) 175 mA Continuous total power dissipation (PD): Cases C and 2 . 1375 mW Case H 675 mW Case P . 1050 mW Operating free-air temperature range (TA) -55oC to +125oC Storage temperature range . -65oC to +150oC Lead temperature 1.6 mm (1/16 inch) from case for 10 seconds +260oC Maximum junction
16、temperature (TJ) +150oC Thermal resistance, junction-to-case (JC): Case C 12.9C/W Case H 11.3C/W Case P . 12.9C/W Case 2 . 12.1C/W Thermal resistance, junction-to-ambient (JA): Case C 83C/W Case H 197C/W Case P . 122C/W Case 2 . 83C/W 1.4 Recommended operating conditions. Single supply voltage range
17、 (VDD) +2.7 V to +6 V Split supply voltage range (+VDD) +1.35 V to +3 V Common-mode input voltage (VICR) . GND to +VDDAmbient operating temperature (TA) . -55oC to +125oC _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum level
18、s may degrade performance and affect reliability. 2/ All voltage values, except differential voltages, are with respect to GND. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00512 DLA LAND AND MARITIME COLU
19、MBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issue
20、s of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard
21、 Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the Standardization Document Order
22、Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regu
23、lations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 as specified herein, or as modified in the device manufacturers Quality Management (QM) plan. The modifi
24、cation in the QM plan shall not affect the form, fit, or function as described herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V. 3.2.1 Case outlines. The case outl
25、ines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and po
26、stirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I
27、. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device
28、. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. Pr
29、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00512 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol
30、Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 1/ Unit Min Max Input offset voltage VIOVDD= +1.5 V, 1 01,03, 2000 V VIC= 0 V, VOUT= 0 V, 2,3 05,07 2200 RS= 50 1 02,04, 1500 2,3 06,08 1700 VDD= +2.5 V, 1 01,03, 2000 VIC= 0 V, VOUT= 0 V, 2,3 05,07 2200 RS= 50
31、1 02,04, 1500 2,3 06,08 1700 VDD= 3 V, Gnd, 1 01,03, 2000 VIC= 0 V, VOUT= 1.5 V, 2,3 05,07 2200 RS= 50 1 02,04, 1500 2,3 06,08 1700 VDD= 5 V, Gnd, 1 01,03, 2000 VIC= 0 V, VOUT= 2.5 V, 2,3 05,07 2200 RS= 50 1 02,04, 1500 2,3 06,08 1700 Input offset current IIOVDD= +1.5 V, RS= 50 , 1 All 7 nA VIC= 0 V
32、, VOUT= 0 V, 2,3 75 VDD= +2.5 V, RS= 50 , 1 7 VIC= 0 V, VOUT= 0 V, 2,3 60 Input bias current IIBVDD= +1.5 V, RS= 50 , 1 All 14 nA VIC= 0 V, VOUT= 0 V, 2,3 75 VDD= +2.5 V, RS= 50 , 1 14 VIC= 0 V, VOUT= 0 V, 2,3 60 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networki
33、ng permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00512 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA +125C unless otherwise sp
34、ecified Group A subgroups Device type Limits 1/ Unit Min Max Common-mode input voltage range VICRCMRR 66 dB, RS= 50 , VDD= 3 V 1 All -0.2 to 3.2 V CMRR 60 dB, RS= 50 , VDD= 3 V 2,3 0 to 3.0 CMRR 71 dB, RS= 50 , VDD= 5 V 1 -0.2 to 5.2 CMRR 60 dB, RS= 50 , VDD= 5 V 2,3 0 to 5 High-level output voltage
35、 VOHIOH= -2.5 mA, VDD= 3 V 1,2,3 All 2.8 V IOH= -10 mA, VDD= 3 V 2.5 IOH= -2.5 mA, VDD= 5 V 4.8 IOH= -10 mA, VDD= 5 V 4.7 Low output voltage VOLIOL= 2.5 mA, VIC= 1.5 V 1,2,3 All 0.2 V IOL= 10 mA, VIC= 1.5 V 0.5 IOL= 2.5 mA, VIC= 2.5 V 0.2 IOL= 10 mA, VIC= 2.5 V 0.3 Short-circuit output current IOSSo
36、urcing, VDD = +1.5 V 1,2,3 All 20 mA Sinking, VDD = +1.5 V 20 Sourcing, VDD = +2.5 V 60 Sinking, VDD = +2.5 V 60 Large signal differential voltage amplification AVDVDD = +1.5 V, 1 All 90 dB RL= 10 k 2,3 89 VDD = +2.5 V, 1 92 RL= 10 k 2,3 90 See footnotes at end of table. Provided by IHSNot for Resal
37、eNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00512 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C
38、TA +125C unless otherwise specified Group A subgroups Device type Limits 1/ Unit Min Max Common-mode rejection ratio CMRR VICR= 0 V to 3 V, 1 All 66 dB RS= 50 , VDD= 3 V 2,3 60 VICR= 0 V to 5 V, 1 71 RS= 50 , VDD= 5 V 2,3 60 Supply voltage rejection ratio kSVRVIC= VDD/ 2, no load, 1 All 80 dB (VDD/
39、VIO) VDD= 2.7 V to 6.0 V 2,3 75 VIC= VDD/ 2, no load, 1 85 VDD= 3.0 V to 5.0 V 2,3 80 Supply current per channel IDDVOUT= 1.5 V, no load, 1 All 0.575 mA VDD= 3 V 2,3 0.9 VOUT= 2.5 V, no load, 1 0.65 VDD= 5 V2,3 1 Supply current per channel in shutdown IDD(SHDN)SHDN 0.8 V, VDD= 3 V 1,2,3 01,02, 07,08
40、 2.5 A (For devices with shutdown feature) SHDN 1.3 V, VDD= 5 V 3 Slew rate SR VOUT(PP)= 2 V, 4 All 1 V/s CL= 160 pF, RL= 10 k 5, 6 0.8 1/ All characteristics are measured with zero common-mode input voltages unless otherwise noted. 3.6 Certificate of compliance. For device classes Q and V, a certif
41、icate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm tha
42、t the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 shall be provided with each lot of microcircuits delivered to this drawing
43、. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00512 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 8 DSCC FORM 2234 APR 97 Device types 01 and 02 (with shutdown) Case outlines H P
44、2 Terminal number Terminal symbol 1 NC NC NC 2 NC -INPUT 1 NC 3 -INPUT 1 +INPUT 1 NC 4 +INPUT 1 -VDD/ GND NC 5 -VDD/ GND NC -INPUT 1 6 NC OUTPUT NC 7 OUTPUT +VDD+INPUT 1 8 +VDDSHDN NC 9 SHDN - NC 10 NC - -VDD/ GND 11 - - NC 12 - - NC 13 - - NC 14 - - NC 15 - - OUTPUT 16 - - NC 17 - - +VDD18 - - NC 1
45、9 - - NC 20 - - SHDN NC = No connect FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00512 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 9 DSCC FORM 22
46、34 APR 97 Device types 03 and 04 (without shutdown) Case outlines H P 2 Terminal number Terminal symbol 1 NC NC NC 2 NC -INPUT 1 NC 3 -INPUT 1 +INPUT 1 NC 4 +INPUT 1 -VDD/ GND NC 5 -VDD/ GND NC -INPUT 1 6 NC OUTPUT NC 7 OUTPUT +VDD+INPUT 1 8 +VDDNC NC 9 NC - NC 10 NC - -VDD/ GND 11 - - NC 12 - - NC
47、13 - - NC 14 - - NC 15 - - OUTPUT 16 - - NC 17 - - +VDD18 - - NC 19 - - NC 20 - - NC NC = No connect FIGURE 1. Terminal connections Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00512 DLA LAND AN
48、D MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 10 DSCC FORM 2234 APR 97 Device types 05 and 06 (without shutdown) Case outlines H P 2 Terminal number Terminal symbol 1 NC OUTPUT 1 NC 2 OUTPUT 1 -INPUT 1 OUTPUT 1 3 -INPUT 1 +INPUT 1 -INPUT 1 4 +INPUT 1 -VDD/ GND +INPUT 1 5 -VDD/ GND +INPUT 2 NC 6 +INPUT 2 -INPUT 2 -VDD/ GND 7 -INPUT 2 O
