1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update drawing to the latest requirements. -sld 07-07-25 Joseph Rodenbeck B Table II, add note to Group C end-point test parameters. Update boilerplate paragraphs. -gz 09-12-02 Charles F. Saffle C Correct dimensions for symbols D, D2, and L1 for
2、case outline U. Correct dimensions for symbols D2, L, and L1 for case outline X. Correct dimensions for symbols D, L, and L1 for case outline Y. Correct dimensions for symbols D, D2, and L1 for case outline Z. Update drawing paragraphs. -gc 13-01-23 Charles F. Saffle REV SHEET REV SHEET REV STATUS R
3、EV C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Gary Zahn DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED BY Greg Cecil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROV
4、ED BY Raymond Monnin MICROCIRCUIT, HYBRID, LINEAR, 5 VOLT , DUAL CHANNEL, DC/DC CONVERTER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 02-11-06 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-02554 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E093-13Provided by IHSNot for Resale
5、No reproduction or networking permitted without license from IHS-,-,- STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-02554 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in
6、 paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following
7、 example: 5962 - 02554 01 H X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet
8、 the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 AFL12005D/CH DC/DC converter, 80 W
9、, 5 V outputs 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G a
10、nd D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high
11、reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) per
12、iodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition docu
13、ment should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. 1.2.4 Case outlines. The
14、case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style U See figure 1 12 Y case configuration with leads bent upwards X See figure 1 12 Straight leads with end mounting through holes Y See figure 1 12 Straight leads with side mou
15、nting through holes Z See figure 1 12 Y case configuration with leads bent downwards 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- STANDARD MICROCIRCUIT DRAWING DLA LAND AN
16、D MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-02554 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Input voltage range -0.5 V dc to +180 V dc Lead temperature (soldering, 10 seconds) +300C Storage temperature -65C to +135C 1.4 Recommended operating conditions. Inp
17、ut voltage range +80 V dc to +160 V dc Output power 2/ 3/ . 80 W Case operating temperature range (TC) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent speci
18、fied herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircui
19、ts. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/or from
20、 the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however,
21、 supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include t
22、he performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-P
23、RF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation a
24、t the maximum levels may degrade performance and affect reliability. 2/ Derate output power linearly above case temperature +125C to 0 at +135C. 3/ Output load must be distributed so that a minimum of 20% of the total output power is being provided by one of the outputs. Provided by IHSNot for Resal
25、eNo reproduction or networking permitted without license from IHS-,-,- STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-02554 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 3.2 Design, construction, and physical dimensions. The design, construction, and physi
26、cal dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless o
27、therwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests
28、 for each subgroup are defined in table I. 3.5 Marking of devices. Marking of devices shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general pe
29、rformance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all p
30、arameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime-VA) upon request. 3.7 Certificate of compliance. A certificate of com
31、pliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conform
32、ance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufactu
33、rers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test
34、 condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DLA Land and Maritime-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power
35、dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TAas specified in accordance with table I of method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical paramete
36、r tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-02554 REVISION LEVEL C SHEET 5 DSC
37、C FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TC +125C VIN= 120 V dc 5%, CL= 0 unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output voltage VOUTIOUT= 8 A, each output 1 01 4.95 5.05 V 2,3 4.90 5.10 Output current 1/ 2/
38、IOUTVIN = 80, 120, and 160 V dc, either output 1,2,3 01 12.8 A Output ripple voltage VRIPVIN = 80, 120, and 160 V dc, B.W. = 10 MHz, IOUT= 8 A, both outputs 1,2,3 01 60 mV p-p Line regulation 3/ VRLINEVIN = 80, 120, and 160 V dc, IOUT= 0, 4, and 8 A, both outputs 1,2,3 01 25 mV Load regulation 3/ VR
39、LOADVIN = 80, 120, and 160 V dc, IOUT= 0, 4, and 8 A, both outputs 1,2,3 01 50 mV Cross regulation 4/ VRCROSSVIN = 80, 120, and 160 V dc Positive output Negative output 1,2,3 01 50 mV 400 Input current IINIOUT = no load 1 01 20 mA 2,3 25 Enable 1, (pin 4) shorted to Input return (pin 2) 1,2,3 3 Enab
40、le 2, (pin 12) shorted to Output return (pin 8) 1,2,3 5 Input ripple current IRIPIOUT = 8 A, B.W. = 10 MHz 1,2,3 01 60 mA p-p Efficiency EFFIOUT = 8 A 1,2,3 01 78 % Isolation ISO Input to output or any pin to case (except pin 3) at 500 V dc, TC = +25C 1 01 100 M Maximum capacitive load 5/ CLNo effec
41、t on dc performance, each output, TC= +25C 4 01 10,000 F Power dissipation load fault PDOverload 1,2,3 01 32 W Short circuit 32 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- STANDARD MICROCIRCUIT DRAWING DLA LAND AND
42、 MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-02554 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TC +125C VIN= 120 V dc 5%, CL= 0 unless otherwise specified Group A subgroups Device type Limits Unit Min Max
43、Current limit point 6/ ICLVOUT = 90% VNOM , each output 1 01 9.20 10.00 A 2 8.40 9.20 3 10.00 11.20 Switching frequency FSIOUT= 8 A 1,2,3 01 500 600 kHz Sync frequency range FSYNCIOUT = 8 A 1,2,3 01 500 700 kHz Output response to step transient load changes 7/ 8/ VOTLOAD50% to/from 100% 4,5,6 01 -45
44、0 +450 mV pk 10% to/from 50% -450 +450 Recovery time, step transient load changes 7/ 8/ TTLOAD50% to/from 100% 4,5,6 01 200 s 10% to/from 50% 400 Output response to transient step line changes 5/ 7/ 9/ VOTLINEInput step, 160 V to/from 400 V dc, IOUT = 8 A 4,5,6 01 -500 +500 mV pk Recovery time trans
45、ient step line changes 5/ 7/ 9/ TTLINEInput step, 160 V to/from 400 V dc, IOUT= 8 A 4,5,6 01 500 s Turn on overshoot 10/ VTonOSIOUT= 0 and 8 A 4,5,6 01 250 mV pk Turn on delay 10/ TonDIOUT= 0 and 8 A 4,5,6 01 120 ms Load fault recovery 10/ TrLF4,5,6 01 120 ms 1/ Parameter verified as part of another
46、 test. 2/ Output load must be distributed so that a minimum of 20% of the total output power is being provided by one of the outputs. 3/ Load current split equally between +VOUTand -VOUT. 4/ Cross regulation measured with load on tested output at 20% while changing the load on other output from 20%
47、to 80%. 5/ Parameter not 100% tested but are guaranteed to the limits specified in the table. 6/ Current limit point is that condition of excess load causing output voltage to drop to 90% of nominal. 7/ Recovery time is measured from the initiation of the transient to where VOUThas returned to withi
48、n 1% of VOUTat 50% load. 8/ Load transient transition time 10 s. 9/ Line transient transition time 100 s. 10/ Turn-on delay is measured with an input voltage rise time of between 100 and 500 volts per millisecond. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-02554 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Case outline
