1、 -REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Table I; For the Input-output isolation current test (II-O) and Channel-channel isolation current test (IISO) changed “RH 45 %“ to “RH 65 %“ in the conditions . Editorial changes throughout. -sld 04-09-15 Raymond Monnin B Added case outline Z. U
2、pdated drawing to reflect the latest requirements. -sld 05-08-26 Raymond Monnin C Updated drawing paragraphs. -sld 12-01-17 Charles F. Saffle REV SHEET REV SHEET REV STATUS REV C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Gary Zahn DLA LAND AND MARITIME COLUMBUS, OHI
3、O 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED BY Greg Cecil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE APPROVED BY Raymond Monnin MICROCIRCUIT, HYBRID, LINEAR, POWER MOSFET, DUAL CHANNEL, OPTOCOUPLER DRAWING
4、APPROVAL DATE 03-07-23 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-03247 SHEET 1 OF 10 DSCC FORM 2233 APR 97 5962-E064-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-03247 DLA LAND AND MARITIME
5、COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identif
6、ying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 03247 01 H X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1)
7、(see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.
8、2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 53252 Dual channel, power MOSFET, optocoupler, 90 V, 0.8 A 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assura
9、nce level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class ava
10、ilable. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H s
11、creening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K,
12、H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specif
13、ied quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style
14、 X See figure 1 8 Dual-in-line Y See figure 1 8 Dual-in-line Z See figure 1 8 Dual-in-line 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A
15、 5962-03247 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Average input current (IF) . 20 mA Peak repetitive input current (IFPK) . 40 mA 2/ Peak surge input current (IFPKsurge) . 100 mA 3/ Continuous output current pe
16、r relay (IO) 0.8 A 4/ Single shot output current per relay (IOPKsurge, pulse width 10 ms) . 3.0 A Output voltage (VO) 90 V dc Output power dissipation (PO) . 1.54 W 5/ Junction temperature (TJ) . +150C Thermal resistance junction-to-case (JC) . 15C/W Lead temperature (soldering, 10 seconds) . +260C
17、6/ Storage temperature range -65C to +150C 1.4 Recommended operating conditions. Input current ON (IFON) . 10 mA minimum to 20 mA maximum Input voltage OFF (VFOFF) 0 to 0.6 V dc maximum Ambient operating temperature range (TA) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, stand
18、ards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid
19、 Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 -
20、 Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the
21、text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 1/ Stresses above the absolute maximum ratings may cause permanent damage to t
22、he device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Pulse width 100 ms, duty cycle 50 %. 3/ Pulse width 0.2 ms, duty cycle 0.1 %. 4/ Maximum average current rating where the case temperature (TC) is maintained below 120C. 5/ Output power dissipation
23、 (PO) is obtained when the part is handling the maximum output current (IO). Care should be taken not to exceed the maximum output dissipation, maximum case temperature, and maximum junction temperature when repetitively switching loads. 6/ Lead temperature soldering occurs 1.6 mm below the seating
24、plane. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-03247 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individua
25、l item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicabl
26、e device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function
27、 of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.
28、2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Truth table(s). The truth table(s) shall be as specified on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified
29、 in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device
30、(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described
31、herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data
32、shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing.
33、 The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provide
34、d with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not aff
35、ect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufactur
36、er under document revision level control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1
37、015 of MIL-STD-883. (2) TAas specified in accordance with table I of method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Pr
38、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-03247 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol
39、Conditions -55C TA+125C unless otherwise specified Group A subgroups Device type Limits Unit Min MaxOutput withstand voltage VO(OFF) VFOFF= 0.6 V, IO= 10 A 1,2,3 01 90 V Output on resistance 1/ R(ON)IFON= 10 mA, IO= 800 mA, pulse duration 30 ms, duty cycle 10%1,2,3 01 1.2 Output leakage current IO(O
40、FF)VFOFF= 0.6 V, VO= 90 V 1,2,3 01 10 A Input forward voltage VFOFFIFON= 10 mA 1,2,3 01 1.0 1.7 V Input reverse breakdown voltage VrIr= 10 A 1,2,3 015.0 V Input-output isolation current 2/ II-OVI-O= 1000 V dc, t = 5 s, RH 65 %, TA= +25C 1 01 1.0 A Channel-channel isolation current 2/ IISOVI-O= 1000
41、V dc, t = 5 s, RH 65 %, TA= +25C 1 01 1.0 A Turn-on time 1/ tONIFON= 10 mA, IO= 0.8 A, pulse duration 30 ms, duty cycle 10%9,10,11 01 6.0 ms Turn-off time 1/ tOFFIFON= 10 mA, IO= 0.8 A, pulse duration 30 ms, duty cycle 10%9,10,11 01 2.0 ms 1/ During the pulse RONmeasurement (IOduration 30 ms), TAand
42、 TCare equal. 2/ This is a momentary withstand test, not a continuous operating condition. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-03247 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL
43、C SHEET 6 DSCC FORM 2234 APR 97 Case outline X. Symbol Millimeters InchesMin Max Min MaxA 6.99 .275A1 1.40 1.65 .055 .065b 0.41 0.53 .016 .021c 0.18 0.33 .007 .013D 9.40 9.91 .370 .390e 2.29 2.79 .090 .110E 9.65 9.91 .380 .390E1 8.13 .320L 1.07 1.32 .042 .052S 0.89 1.27 .035 .050Case outline Y. Symb
44、ol Millimeters InchesMin Max Min MaxA 6.60 .260A1 0.76 1.27 .030 .050b 0.41 0.53 .016 .021c 0.18 0.33 .007 .013D 9.40 9.91 .370 .390e 2.29 2.79 .090 .110E 8.13 .320eA 7.37 7.87 .290 .310L 12.70 .500Q 0.51 .020S 0.89 1.27 .035 .050NOTES: 1. The U.S. government preferred system of measurement is the m
45、etric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin 1 is indicated by the ESD triangle(s) marked on top of the package. FIGURE 1. Case outline(s). Provided by
46、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-03247 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Case outline Z. Symbol Millimeters InchesMin Max Min MaxA 4.57 .180A1 1
47、.40 1.65 .055 .065b 0.41 0.53 .016 .021c 0.18 0.33 .007 .013D 9.40 9.91 .370 .390e 2.29 2.79 .090 .110E 12.45 12.70 .490 .500E1 7.87 .310L 2.34 .092R .51 TYP .020 TYPS 0.89 1.27 .035 .050NOTES: 1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inch
48、-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin 1 is indicated by the ESD triangle(s) marked on top of the package. FIGURE 1. Case outline(s) - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-03247 DLA LAND A
