1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Table II, add note to Group C end-point test parameters. Update boilerplate paragraphs. -gz 10-11-01 Charles F. Saffle B Figure 1: Corrected the dimension q3 from “17.78 and 18.03 mm“ and “.700 and .710 inches“ to “15.24 and 15.49 mm“ and “.600 a
2、nd .610 inches“. Editorial changes throughout. -sld 13-12-04 Charles F. Saffle REV SHEET REV SHEET REV STATUS REV B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Steve Duncan DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MIC
3、ROCIRCUIT DRAWING CHECKED BY Greg Cecil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Raymond Monnin MICROCIRCUIT, HYBRID, 12 VOLT, DUAL CHANNEL, DC/DC CONVERTER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 06-06-09 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 672
4、68 5962-04243 SHEET 1 OF 10 DSCC FORM 2233 APR 97 5962-E435-13Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-04243 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR
5、97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assu
6、rance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 04243 01 K X A Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing
7、 number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type. The device type identify the circuit function as follow
8、s: Device type Generic number Circuit function 01 S2812D DC/DC converter, 10 W, 12 V output 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certif
9、ication as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality cla
10、ss level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer s
11、pecified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must b
12、e specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow
13、. This product may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-04243 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.2.4
14、Case outline. The case outline are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 7 Straight leads with end mounting tabs 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum rating
15、s. 1/ Input voltage range -0.5 V dc to +60 V dc Lead temperature (soldering, 10 seconds) +300C Storage temperature range -55C to +135C 1.4 Recommended operating conditions. Input voltage range +18 V dc to +40 V dc Output power . 10 W Case operating temperature range (TC) . -55C to +85C 2. APPLICABLE
16、 DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT O
17、F DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Sta
18、ndard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/quicksearch.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the eve
19、nt of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum ratings
20、may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-04243 DLA LAND AND MARITIME C
21、OLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of a
22、ll tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be m
23、et for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MI
24、L-PRF-38534 and herein. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical pe
25、rformance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3
26、.5 Marking of devices. Marking of devices shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the
27、 manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those whi
28、ch, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacture
29、r in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as requir
30、ed in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modif
31、ication in the QM plan shall not affect the form, fit, or function as described herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-04243 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B S
32、HEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TC +85C VIN = 28 V dc 5%, CL = 0 unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output voltage 1/ VOUTIOUT= 0.66 A 1 01 11.88 12.12 V 2, 3 11.76 12.24 Output curren
33、t 2/ 3/ IOUTVIN= 18, 28, and 40 V dc Either output 1, 2, 3 01 0.66 A Output ripple voltage 1/ 4/ VRiPVIN= 18, 28, and 40 V dc IOUT= 0.66 A, BW = 10 MHz 1, 2, 3 01 80 mV p-p Line regulation 1/ VRLINEVIN= 18, 28, and 40 V dc IOUT= 0.06, 0.33, and 0.66 A 1, 2, 3 01 -0.5 +0.5 % Load regulation 1/ VRLOAD
34、VIN= 18, 28, and 40 V dc IOUT= 0.06, 0.33, and 0.66 A 1, 2, 3 01 -1.0 +1.0 % Cross regulation 5/ VRCROSSVIN= 18, 28, and 40 V dc 1, 2, 3 01 -3.0 +3.0 % Input current IINIOUT = 0 A, pin 4 open 1, 2, 3 01 70 mA Pin 4 shorted to pin 2 1, 2, 3 01 5 mA Efficiency 1/ EFFIOUT= 0.66 A 1, 2, 3 01 76 % Isolat
35、ion ISO Input to output or any pin to case except pin 2 at 500 V dc, TC= +25C 1 01 100 M Maximum capacitive load 1/ 6/ 7/ CLIOUT= 0.66 A, Each output, TC= +25C 1 01 90 F Power dissipation load fault PDShort circuit, overload 8/ 1, 2, 3 01 9 W Current limit point 1/ 9/ ICLVOUT= 90% of nominal 1, 2, 3
36、 01 105 160 % Switching frequency FS1, 2, 3 01 475 575 kHz Output response to step load changes 1/ 10/ VTLD50% to/from 100% load 4, 5, 6 01 -300 300 mV pk Recovery time, step load changes 1/ 10/ 11/ TTLD50% to/from 100% load 4, 5, 6 01 200 s See footnotes at end of table. Provided by IHSNot for Resa
37、leNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-04243 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -5
38、5C TC +85C VIN = 28 V dc 5%, CL = 0 unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output response to step line changes 1/ 7/ 12/ VTLNInput step 18 V to/from 40 V IOUT= 0.66 A 4, 5, 6 01 -300 300 mV pk Recovery time, step line changes 1/ 7/ 11/ 12/ TTLNInput step 18 V t
39、o/from 40 V IOUT= 0.66 A 4, 5, 6 01 200 s Turn-on overshoot 1/ VOS10% load, 100% load Enable (pin 4) = on 4, 5, 6 01 1400 mV Turn-on delay 1/ 13/ TDLY10% load, 100% load Enable (pin 4) = on 4, 5, 6 01 10 ms 1/ Load currents split equally between outputs. 2/ Parameter verified during line and load re
40、gulation tests. 3/ Output load currents must be distributed such that at least 20% of the total load current is being provided by one of the outputs. 4/ Guaranteed for a DC to 20 MHz bandwidth. Tested using a 20 kHz to 10 MHz bandwidth. 5/ Cross regulation is measured with 20% rated load on output u
41、nder test while changing the load on the other output from 20% to 80% of rated. 6/ Capacitive load may be any value from 0 to the maximum limit without compromising DC performance. 7/ Parameter is tested as part of design characterization or after design changes. Thereafter, parameter shall be guara
42、nteed to the limits specified in table I. 8/ Overload power dissipation is defined as the device power dissipation with the load set such that VOUT= 90% of nominal. 9/ Current limit point expressed as a percentage of full rated load current. 10/ Load step transition time 10 s. 11/ Recovery time is m
43、easured from the initiation of the transient to where VOUT has returned to within 1% of its steady state value. 12/ Line step transition time 100 s. 13/ Turn-on delay time from either a step application of input power or a logic low to a logic high transition on the enable pin (pin 4) to the point w
44、here VOUT= 90% of nominal. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-04243 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 Symbol Millimeters Inches Min Ma
45、x Min Max A 10.8 .425 D 56.00 56.26 2.205 2.215 D1 43.30 43.56 1.705 1.715 D2 57.53 2.265 E 33.15 33.40 1.305 1.315 e1 4.95 5.21 .195 .205 F 1.14 1.40 .045 .055 L 6.22 6.99 .245 .275 L1 5.46 5.72 .215 .225 q 49.66 49.91 1.955 1.965 q1 15.11 15.37 .595 .605 q2 8.89 9.14 .350 .360 q3 15.24 15.49 .600
46、.610 S 3.81 4.06 .150 .160 b 0.64 0.89 .025 .035 p 3.43 3.68 .135 .145 NOTES: 1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the in
47、ch-pound units shall rule. 2. Lead identification for reference only. 3. Case outline weight: 50 grams maximum. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-04243 DLA LAND AND MARIT
48、IME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Terminal number Terminal symbol 1 Positive Input 2 Case 3 Input Return 4 Enable 5 Negative Output 6 Output Return 7 Positive Output FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-04243 DLA LAND AND M
