1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Figure 1: Corrected the dimension q3 from “17.78 and 18.03 mm“ and “.700 and .710 inches“ to “15.24 and 15.49 mm“ and “.600 and .610 inches“. Editorial changes throughout. -sld 13-12-04 Charles F. Saffle REV SHEET REV SHEET REV STATUS REV A A A A
2、 A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Greg Cecil DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED BY Greg Cecil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Charles F. Saffle
3、MICROCIRCUIT, HYBRID, 7 VOLT, SINGLE CHANNEL, DC/DC CONVERTER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 13-03-05 AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-13216 SHEET 1 OF 10 DSCC FORM 2233 APR 97 5962-E437-13 Provided by IHSNot for ResaleNo reproduction or networki
4、ng permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962- 13216 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PR
5、F-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 13216 01 K
6、 X A Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specifie
7、d RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 S2807S DC/DC Converter, 10 W, 7 V output 1.2.3 Device class d
8、esignator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance level
9、s are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required.
10、G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections
11、(Group A, B, C and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure t
12、hat the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking p
13、ermitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962- 13216 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptiv
14、e designator Terminals Package style X See Figure 1 7 Straight leads with end mounting tabs 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Input voltage range -0.5 V dc to +60 V dc Lead temperature (soldering, 10 seconds) +300C Storage tem
15、perature range -55C to +135C 1.4 Recommended operating conditions. Input voltage range +18 V dc to +40 V dc Output Power . 10W Case operating temperature range (TC) . -55C to +85C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards,
16、and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEF
17、ENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are
18、available online at http:/quicksearch.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing
19、 takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance
20、and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962- 13216 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requireme
21、nts. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated
22、 for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form
23、, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herei
24、n and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operat
25、ing temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device
26、shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables
27、format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control
28、by the manufacturer and be made available to the preparing activity (DLA Land and Maritime-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to
29、 DLA Land and Maritime-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing.
30、4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. Provided
31、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962- 13216 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Condi
32、tions -55C TC+85C VIN = 28 V dc 5%, CL = 0 unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output voltage VOUTIOUT= 1.43 A 1 01 +6.93 +7.07 V 2, 3 +6.895 +7.105 Output current 1/ IOUTVIN= 18, 28, and 40 V dc 1, 2, 3 01 1.43 A Output ripple voltage 2/ VRiPVIN= 18, 28, and
33、 40 V dc, IOUT= 1.43 A, BW = 10 MHz 1, 2, 3 01 45 mV p-p Line regulation VRLINEVIN= 18, 28, and 40 V dc, IOUT= 0, 0.0715, and 1.43 A 1, 2, 3 01 -0.5 +0.5 % Load regulation VRLOADVIN= 18, 28, and 40 V dc, IOUT= 0, 0.0715, and 1.43 A 1, 2, 3 01 -1.0 +1.0 Input current IINIOUT= 0 A, Pin 4 open 1, 2, 3
34、01 70 mA Pin 4 shorted to pin 2 1, 2, 3 5 Efficiency EFFIOUT= 1.43 A 1, 2, 3 01 76 % Isolation ISO Input to output or any pin to case except pin 2 at 500 V dc, TC= +25C 1 01 100 M Maximum capacitive load 3/ 4/ CLNo effect on dc Performance, TC= +25C 4 01 750 F Power dissipation load fault PDShort Ci
35、rcuit, Overload 5/ 1, 2, 3 01 9 W Current limit point 6/ ICLVOUT= 90% of nominal 1, 2, 3 01 105 144 % Switching frequency FS1, 2, 3 01 475 575 kHz Output response to step load changes 7/ VTLD50% to/from 100% Load 4, 5, 6 01 -300 300 mV pk Recovery time, step load changes 7/ 8/ TTLD50% to/from 100% L
36、oad 4, 5, 6 01 200 s See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962- 13216 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE
37、I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TC+85C VIN = 28 V dc 5%, CL = 0 unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output response to step line changes 3/ 9/ VTLNInput step 18 V to/from 40 V, IOUT= 1.43 A 4, 5, 6 01 -300 30
38、0 mV pK Recovery time, step line changes 3/ 8/ 9/ TTLNInput step 18 V to/from 40 V, IOUT= 1.43 A 4, 5, 6 01 200 s Turn-On overshoot VOS10% load and 100% load, Enable = on 4, 5, 6 01 750 mV Turn-On Delay 10/ TDLY10% load and 100% load, Enable = on 4, 5, 6 01 10 ms 1/ Parameter verified during line an
39、d load regulation tests. 2/ Guaranteed for a DC to 20 MHz bandwidth. Tested using a 20 kHz to 10 MHz bandwidth. 3/ Parameter is tested as part of design characterization or after design changes. Thereafter, parameter shall be guaranteed to the limits specified in table I. 4/ Capacitive load may be a
40、ny value from 0 to the maximum limit without compromising DC performance. 5/ Overload power dissipation is defined as the device power dissipation with the load set such that VOUT= 90% of nominal. 6/ Current limit point expressed as a percentage of full rated load current. 7/ Load step transition ti
41、me 10 s. 8/ Recovery time is measured from the initiation of the transient to where VOUT has returned to within 1% of its steady state value. 9/ Line step transition time 100 s. 10/ Turn-on delay time from either a step application of input power or a logic low to a logic high transition on the enab
42、le pin (pin 4) to the point where VOUT= 90% of nominal. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962- 13216 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 Ca
43、se Outline X. Symbol Millimeters Inches Min Max Min Max A 10.8 .425 D 56.00 56.26 2.205 2.215 D1 43.30 43.56 1.705 1.715 D2 57.53 2.265 E 33.15 33.40 1.305 1.315 e1 4.95 5.21 .195 .205 F 1.14 1.40 .045 .055 L 6.22 6.99 .245 .275 L1 5.46 5.72 .215 .225 q 49.66 49.91 1.955 1.965 q1 15.11 15.37 .595 .6
44、05 q2 8.89 9.14 .350 .360 q3 15.24 15.49 .600 .610 S 3.81 4.06 .150 .160 b 0.64 0.89 .025 .035 p 3.43 3.68 .135 .145 NOTES: 1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts b
45、etween the metric and inch-pound units, the inch-pound units shall rule. 2. Lead identification for reference only. 3. Case outline weight: 50 grams maximum. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUI
46、T DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962- 13216 REVISION LEVEL A SHEET 8 DSCC FORM 2234 APR 97 Device Type 01 Case outline X Terminal number Terminal Symbol 1 Positive Input 2 Case 3 Input Return 4 Enable 5 N/C 6 Positive Output 7 Output Return FIGURE 2. Terminal connect
47、ions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962- 13216 REVISION LEVEL A SHEET 9 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-PRF-3853
48、4 test requirements Subgroups (in accordance with MIL-PRF-38534, group A test table) Interim electrical parameters Final electrical parameters 1*, 2, 3, 4, 5, 6 Group A test requirements 1, 2, 3, 4, 5, 6 Group C end-point electrical parameters 1, 2, 3, 4, 5, 6 End-point electrical parameters for Radiation Hardness Assurance (RHA) devices Not applicable * PDA applies to subgroup 1. 4.2 Screen
