1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED C Add logic diagram. Revise to military format. Delete vendors CAGE 34335, 07263, and 27014. Change ICC1, ICC2. and tPLH2. Add footnote 3/. Allow CL= 45 pF testing. Editorial changes throughout. 87-12-31 M. A. Frye D Changes in accordance with NOR
2、5962-R141-92. - pn 92-02-21 Monica L. Poelking E Update to reflect latest changes in format and requirements. Editorial changes throughout. -les 03-05-27 Raymond Monnin F Add class “V“ to document. Update to reflect latest changes in format and requirements. Editorial changes throughout. - les 03-11
3、-13 Raymond Monnin G Update drawing to current requirements. Editorial changes throughout. - gap 09-07-08 Charles F. Saffle CURRENT CAGE CODE 67268 The original first sheet of this drawing has been replaced. REV SHET REV SHET REV STATUS REV G G G G G G G G G G G OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10
4、11 PMIC N/A PREPARED BY T. E. Gordon DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY Robert F. Gonzales APPROVED BY N. A. Hauck MICR
5、OCIRCUIT, DIGITAL, BIPOLAR, LOW-POWER SCHOTTKY TTL, MULTIPLEXER, MONOLITHIC SILICON DRAWING APPROVAL DATE 76-11-24 AMSC N/A REVISION LEVEL G SIZE A CAGE CODE 14933 76037 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E172-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without lice
6、nse from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 76037 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) an
7、d space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following exam
8、ples. For device classes M and Q: 76037 01 E X Drawing number Device type (see 1.2.2)Case outline (see 1.2.4)Lead finish (see 1.2.5)For device class V: 5962 - 76037 01 V E X Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.
9、4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA
10、 levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54LS257 Quad two-input data selector/multiplexer three-state output, wi
11、th enable 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as listed below. Since the device class designator has been added after the original issuance of this drawing, device classes M and Q designators will not be included in th
12、e PIN and will not be marked on the device. Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-385
13、35 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 76037 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outlines. The case outlines are as design
14、ated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 dual-in-line package F GDFP2-F16 or CDFP3-F16 16 flat package 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535
15、, appendix A for device class M. 1.3 Absolute maximum ratings. 1/ Supply voltage range . -0.5 V dc to +5.5 V dc Input voltage range . -1.5 V dc at -18 mA to +5.5 V dc Storage temperature range -65C to +150C Maximum power dissipation (PD) 2/ . 93.5 mW Lead temperature (soldering, 10 seconds) +300C Th
16、ermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) +175C 1.4 Recommended operating conditions. Supply voltage range (VCC) . 4.5 V dc minimim to 5.5 V dc maximum Minimum high level input voltage (VIH) 2.0 V dc Maximum low level input voltage (VIL) . 0.7 V dc Case ope
17、rating temperature range (TC) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are
18、those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Cas
19、e Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Ave
20、nue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a spec
21、ific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Must withstand the added PDdue to short circuit test e.g., IOS.Provided by IHSNot fo
22、r ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 76037 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for
23、device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for devi
24、ce class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and
25、V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2.
26、 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I a
27、nd shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in
28、1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall s
29、till be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required i
30、n MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of thi
31、s drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of s
32、upply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required
33、 for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein)
34、 involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documenta
35、tion. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 11 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo
36、reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 76037 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TC+125C un
37、less otherwise specified Group A subgroups Limits Unit Min MaxHigh level output voltage VOHVCC= 4.5 V, IOH= -1.0 mA, VIH= 2.0 V, VIL= 0.7 V 1, 2, 3 2.4 V Low level output voltage VOLVCC= 4.5 V, IOL= 12 mA, VIH= 2.0 V, VIL= 0.7 V 1, 2, 3 0.4 V Input clamp voltage VIC VCC= 4.5 V, IIL= -18 mA TC= +25C
38、1 -1.5 V Low level input current at A, B, or output control IIL1VCC= 5.5 V, VIL= 0.4 V 1, 2, 3 -0.4 mA Low level input current at select IIL2VCC= 5.5 V, VIL= 0.4 V 1, 2, 3 -0.8 mA High level input current at A, B, or output control IIH1VCC= 5.5 V, VIH= 2.7 V 1, 2, 3 20 A IIH2VCC= 5.5 V, VIH= 5.5 V 1
39、, 2, 3 100 A High level input current at select IIH3VCC= 5.5 V, VIH= 2.7 V 1, 2, 3 40 A IIH4VCC= 5.5 V, VIH= 5.5 V 1, 2, 3 200 A Off state output current IOZL VCC= 5.5 V, VO= 0.4 V 1, 2, 3 -20 A IOZH VCC= 5.5 V, VO= 2.7 V 1, 2, 3 20 A Short circuit output current IOS VCC= 5.5 V, VOUT= 0.0 V 1/ 1, 2,
40、 3 -15 -130 mA Supply current ICC1VCC= 5.5 V, VIN(data) = 5.5 V, VIN(output control) = 0.0 V 1, 2, 3 12 mA ICC2VCC= 5.5 V, VIN(data) = 0.0 V, VIN(output control) = 0.0 V 1, 2, 3 18 mA CC3VCC= 5.5 V, VIN(output control) = 5.5 V 1, 2, 3 19 mA Functional tests See 4.4.1c 7, 8 See footnotes at end of ta
41、ble. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 76037 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics -
42、Continued. Test Symbol Conditions -55C TC+125C unless otherwise specified Group A subgroups Limits Unit Min MaxPropagation delay time, from data to Y tPHL1VCC= 5.0 V, RL= 2 k5% CL= 50 pF 10% 9 23 ns 10, 11 35 tPLH12/ 3/ CL= 50 pF 10% 9 23 ns 10, 11 35 Propagation delay time, from select to Y tPHL2CL
43、= 50 pF 10% 9 26 ns 10, 11 39 tPLH2CL= 45 pF 10% 9 24 ns 10, 11 34 CL= 50 pF 10% 9 26 ns 10, 11 39 Enable time, from output control to Y tPZL1CL= 50 pF 10% 9 35 ns 10, 11 53 tPZH1CL= 50 pF 10% 9 35 ns 10, 11 53 Disable time, from output control to Y tPLZ1CL= 50 pF 10% 9 30 ns 10, 11 45 tPHZ1CL= 50 p
44、F 10% 9 46 ns 10, 11 60 1/ Not more than one output should be shorted at a time, and the duration of the short-circuit condition should not exceed one second. 2/ Propagation delay time, enable time, and disable time testing may be performed using either CL= 45 pF or CL= 50 pF. However, the manufactu
45、rer must certify and guarantee that the microcircuits meet the switching test limits specified for a 50 pF load. 3/ RLcan be tested using RL= 2 k or RL= 667 . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 76037
46、DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 7 DSCC FORM 2234 APR 97 Device type 01 Case outlines E and F Terminal number Terminal symbol 1 A /B 2 1A 3 1B 4 1Y 5 2A 6 2B 7 2Y 8 GND 9 3Y 10 3B 11 3A 12 4Y 13 4B 14 4A 15 G 16 VCCFIGURE 1. Terminal connections. Inputs
47、 Output Output control G Select A /B A B Y H X X X Z L L L X L L L H X H L H X L L L H X H H H = High level. L = Low level. X = Irelevant. Z = High impedance (off) FIGURE 2. Truth table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROC
48、IRCUIT DRAWING SIZE A 76037 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 8 DSCC FORM 2234 APR 97 FIGURE 3. Logic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 76037 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 9 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. For device classes Q and V, sampling and inspecti
