1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Complete document revision also added device types 02, 03, 04, 05. 78-02-03 N. A. HAUCK B Complete document revision: deleted type 02. 79-07-11 N. A. HAUCK C Add condition C to burn-in. Format changes. 80-07-11 D. HILL D Types 01, 03, and 04 INAC
2、TIVE for New Design. Use M38510/11501, 11502, and 11503, respectively, for case “X”; and M38510/11505, 11506, and 11507 respectively, for case “Y”. Type 05 still active. 82-07-20 N. A. HAUCK E Add case outlines H, P, and 2. Add vendor CAGE 01295 as a supplier for 01HX, 01PX, and 012X. Delete vendor
3、CAGE numbers 07263 and 27014 from drawing. Engineering and editorial changes throughout. 93-05-04 M. A. FRYE F Drawing updated to reflect current requirements. -rrp 05-12-06 R. MONNIN G Update drawing as part of five year review. -rrp 12-02-21 C. SAFFLE CURRENT CAGE CODE 67268 THE ORIGINAL FIRST SHE
4、ET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV G G G SHEET 15 16 17 REV STATUS REV G G G G G G G G G G G G G G OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY WILLIAM E. SHOUP DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROC
5、IRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY C.R. JACKSON APPROVED BY N. A. HAUCK MICROCIRCUIT, LINEAR, NEGATIVE, FIXED, VOLTAGE REGULATOR, MONOLITHIC SILICON DRAWING APPROVAL DATE 77-08-19 AMSC N/A REVISION LEVEL G SIZE A C
6、AGE CODE 14933 77040 SHEET 1 OF 17 DSCC FORM 2233 APR 97 5962-E195-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 77040 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 2 DSCC FORM 2234 A
7、PR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 77040 01 H A Drawing number D
8、evice type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 7905/ LM120-5 Negative, voltage regulator, fixed -5 volts 03 7912/ LM120-12 Negative, voltage regu
9、lator, fixed -12 volts 04 7915/ LM120-15 Negative, voltage regulator, fixed -15 volts 05 7924/ LM120-24 Negative, voltage regulator, fixed -24 volts 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package st
10、yle H GDFP1-F10 or CDFP2-F10 10 Flat pack P GDIP1-T8 or CDIP2-T8 8 Dual-in-line X MACY1-X3 3 TO-5 can Y MBFM1-P2 2 TO-3 flange mount 2 CQCC1-N20 20 Square leadless chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Input voltag
11、e (VIN): Device types 01, 03, 04 . -35 V Device type 05 . -40 V Storage temperature range . -65C to +150C Lead temperature (soldering, 10 seconds) 300C Power dissipation (PD): 1/, 2/ Case outline H . 0.675 W Case outline P . 1.050 W Case outline X . 2.0 W Case outline Y . 20.0 W Case outline 2 1.375
12、 W Design output current (ID): Case outlines H, P, X, and 2 0.5 A Case outline Y . 1.0 A Thermal resistance, junction-to-case (JC): Case outlines H, P, and 2 See MIL-STD-1835 Case outline X . 15C/W Case outline Y . 3C/W 1/ Must withstand the added PDdue to short circuit test; e.g., IOS. 2/ For tempe
13、ratures above 25C, derate at a factor of 5.4 mW/C for case outline H, 8.4 mW/C for case outline P, and 11 mW/C for case outline 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 77040 DLA LAND AND MARITIME COLUMB
14、US, OHIO 43218-3990 REVISION LEVEL G SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings Continued. Thermal resistance, junction-to-case (JA): Case outline H . 185C/W Case outline P . 119C/W Case outline X . 150C/W Case outline Y . 35C/W Case outline 2 65C/W 1.4 Recommended operating conditio
15、ns. Input voltage range (VIN): Device type 01 . -7 V to -25 V Device type 03 . -15 V to -32 V Device type 04 . -18.5 V to -35 V Device type 05 . -28 V to -38 V Ambient operating temperature (TA) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The followi
16、ng specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, Ge
17、neral Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit
18、 Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing a
19、nd the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ST
20、ANDARD MICROCIRCUIT DRAWING SIZE A 77040 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and
21、as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers a
22、pproved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications sh
23、all not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-P
24、RF-38535, appendix A and herein. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical perfor
25、mance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 M
26、arking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in co
27、mpliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer
28、 in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix
29、 A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be r
30、equired for any change that affects this drawing. 3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available
31、onshore at the option of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 77040 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical perfo
32、rmance characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Cases H, P, and 2 Output voltage VOUTVIN= -7 V to -25 V, IL= 5 mA to 350 mA 1, 2, 3 01 -5.25 -4.75 V Line regulation VRLINEVIN= -7 V to -25 V, IL= 350 mA 1 01
33、-50 +50 mV VIN= -8 V to -18 V, IL= 350 mA 2, 3 -30 +30 Load regulation VRLOADVIN= -10 V , IL= 5 mA to 500 mA 1, 2, 3 01 -100 +100 mV Standby current drain ISCDVIN= -10 V, IL= 350 mA 1, 2, 3 01 2 mA Standby current drain change vs. line voltage ISCD/ (line) VIN= -8 V to -25 V, IL = 350 mA 1, 2, 3 01
34、-0.4 +0.4 mA Standby current drain change vs. load current ISCD/ (load) VIN= -10 V, IL= 5 mA to 350 mA 1, 2, 3 01 -0.4 +0.4 mA Output short circuit current IOSVIN= -30 V 1, 2, 3 01 600 mA Peak output current 2/ IPKVIN= -10 V, TA= 25C 1 01 0.5 1.4 A Ripple rejection 2/ VIN/ VOUTVIN= -8 V to -18 V, IL
35、= 100 mA, f = 120 Hz 4, 5, 6 01 50 dB VIN= -8 V to -18 V, TA= 25C, IL= 300 mA, f = 120 Hz 4 01 54 Output noise voltage 2/ VNOVIN= -10 V, TA= 25C, IL = 350 mA, f = 10 Hz to 100 kHz 1 01 400 V Temperature coefficient of output voltage 2/ VRTHVIN= -10 V, IL= 5 mA 1, 2, 3 01 -1.5 +1.5 mV/C Dropout volta
36、ge VDROPVIN= -10 V, IL= 350 mA 1, 2, 3 01 2.3 V See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 77040 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 6 DSCC FO
37、RM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Case X Output voltage VOUTVIN= -8 V, IL= 5 mA, 0.5 A 1, 2, 3 01 -5.25 -4.75 V VIN= -20 V, IL= 5 mA, 0.5 A 1, 2,
38、3 -5.25 -4.75 VIN= -30 V, IL= 5 mA, 50 mA 1, 2, 3 -5.25 -4.75 VIN= -10 V, IL= 5 mA, TA= 150C 1, 2, 3 -5.30 -4.70 Line regulation VRLINE-30 V VIN -8 V, IL= 50 mA 1, 2, 3 01 -150 150 mV -25 V VIN -8 V, IL= 350 mA -50 50 Load regulation VRLOADVIN= -10 V, 5 mA IL 500 mA 1, 2, 3 01 -100 100 mV VIN= -30 V
39、, 5 mA IL 50 mA -150 150 Standby current drain ISCDVIN= -10 V, IL= 5 mA 1, 2, 3 01 0.5 3.0 mA VIN= -30 V, IL= 5 mA 0.5 4.0 Standby current drain change vs. line voltage ISCD/ (line) -30 V VIN -8 V, IL= 5 mA 1, 2, 3 01 -1.0 1.0 mA Standby current drain change vs. load current ISCD/ (load) 5 mA IL 500
40、 mA, VIN= -10 V 1, 2, 3 01 -0.5 0.5 mA Output short circuit current IOSVIN= -25 V 1, 2, 3 01 0.00 1.50 A VIN= -30 V 0.00 1.00 Peak output current IPKVIN= -8 V, forced VOUT= 0.48 V 1, 2, 3 01 0.5 2.0 A Ripple rejection VIN/ VOUTVIN= -10 V, IL= 125 mA, ei= 1 Vrmsat f = 2400 Hz 4, 5, 6 01 45 dB Output
41、noise voltage VNOVIN= -10 V, TA= 25C, IL= 50 mA 1 01 250 Vrms Thermal regulation VRTHVIN= -15 V, IL= 500 mA, TA= 25C 1 01 -50 50 mV Voltage start up VSTARTVIN= -20 V, RL= 10 1, 2, 3 01 -5.25 -4.75 V Line transient response VOUT/VINVIN= -10 V, IL= 5 mA, VPLUS= -3.0 V, TA= 25C 4 01 30.0 mV/V Load tran
42、sient response VOUT/ILVIN= -10 V, IL= 50 mA, IL= 200 mA, TA= 25C 4 01 2.5 mV/mA See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 77040 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990
43、REVISION LEVEL G SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Case Y Output voltage VOUTVIN= -8 V, IL= 5 mA,1.0 A 1, 2, 3 01 -5.25 -4.75 V VIN
44、= -20 V, IL= 5 mA, 1.0 A -5.25 -4.75 VIN= -30 V, IL= 5 mA, 0.1 A -5.25 -4.75 VIN= -10 V, IL= 5 mA, TA= 150C -5.30 -4.70 Line regulation VRLINE-30 V VIN -8 V, IL= 0.1 A 1, 2, 3 01 -150 150 mV -25 V VIN -8 V, IL= 0.5 A -75 75 Load regulation VRLOADVIN= -10 V, 5 mA IL 1.0 A 1, 2, 3 01 -100 100 mV VIN=
45、-30 V, 5 mA IL 0.1 A -150 150 Standby current drain ISCDVIN= -10 V, IL= 5 mA 1, 2, 3 01 0.5 3.0 mA VIN= -30 V, IL= 5 mA 0.5 4.0 Standby current drain change vs. line voltage ISCD(line) -30 V VIN -8 V, IL= 5 mA 1, 2, 3 01 -1.0 1.0 mA Standby current drain change vs. load current ISCD(load) 5 mA IL 1.
46、0 A, VIN= -10 V 1, 2, 3 01 -0.5 0.5 mA Output short circuit current IOSVIN= -25 V 1, 2, 3 01 0.00 3.50 A VIN= -30 V 0.00 2.00 Peak output current IPKVIN= -8 V, forced VOUT= 0.48 V 1, 2, 3 01 1.0 4.50 A Ripple rejection VIN/ VOUTVIN= -10 V, IL= 350 mA, ei= 1 Vrmsat f = 2400 Hz 4, 5, 6 01 45 dB Output
47、 noise voltage VNOVIN= -10 V, TA= 25C, IL= 0.1 A 1 01 250 Vrms Thermal regulation VRTHVIN= -15 V, IL= 1.0 A, TA= 25C 1 01 -50 50 mV Voltage start up VSTARTVIN= -20 V, RL= 5 1, 2, 3 01 -5.25 -4.75 V Line transient response VOUT/VINVIN= -10 V, IL= 5 mA, VPLUS= -3.0 V, TA= 25C 4 01 30.0 mV/V Load trans
48、ient response VOUT/ILVIN= -10 V, IL= 100 mA, IL= 400 mA, TA= 25C 4 01 2.5 mV/mA See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 77040 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performanc
