1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED H Add vendors CAGE 07933, 04713, and 27014. Add device type 02. Inactive case D for new design. Change input offset current limit for +25C. Change group A subgroups for large signal voltage gain test and output voltage swing test. Editorial changes
2、 throughout. 89-07-20 M.A. Frye J Sheet 4: Input bias current test, IB, device type 02; for group A subgroup 1, add “-50 nA” in min column. For subgroups 2 and 3 add “-100 nA” in min column. Changes in accordance with NOR 5962-R261-94. 94-08-12 M.A. Frye K Update boilerplate. Changes to thermal resi
3、stance, junction-to-ambient (JA). Add case outline X. Editorial changes throughout. 97-07-10 R. Monnin L Case outline “X“ dimensions L, R, and R1 are updated. - rrp 97-12-15 R. Monnin M Changes to IIO, IB, VICR, AVD, and VOLtests in table I. Add ICCand IOStests to table I. - rrp 98-03-02 R. MonninN
4、Add device class “V” device and delete figure 1. - ro 03-04-24 R. Monnin P Drawing updated to reflect current requirements. - rrp 05-04-04 R. Monnin R Make correction to VOLtest limit by deleting “20 V” and substituting “20 mV” as specified under Table I. Update boilerplate paragraphs to current MIL
5、-PRF-38535 requirements. - ro 11-08-03 C. Saffle THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. CURRENT CAGE CODE 67268 REV SHET REV SHET REV STATUS REV R R R R R R R R R R OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY WILLIAM E. SHOUP DLA LAND AND MARITIME COLUMBUS, OHIO 43
6、218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY C. R. JACKSON APPROVED BY N. A. HAUCK MICROCIRCUIT, LINEAR, QUAD OPERATIONAL AMPLIFIER, MONOLITHIC SILICON DRAWING APPROV
7、AL DATE 77-09-13 AMSC N/A REVISION LEVEL R SIZE A CAGE CODE 14933 77043 SHEET 1 OF 10 DSCC FORM 2233 APR 97 5962-E418-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 77043 DLA LAND AND MARITIME COLUMBUS, OHIO 4
8、3218-3990 REVISION LEVEL R SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are ref
9、lected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following examples. For device classes M and Q: 77043 01 C A Drawing number Device type (see 1.2.2) Case outline (see 1.2
10、.4)Lead finish (see 1.2.5)For device class V: 5962 - 77043 01 V C A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Leadfinish (see 1.2.5) / (see 1.2.3) /Drawing number 1.2.1 RHA designator. Device classes Q and V RHA m
11、arked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Dev
12、ice type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 LM124 Quad operational amplifier 02 LM124A Quad operational amplifier 1.2.3 Device class designator. The device class designator is a single letter identifying the product assuran
13、ce level as listed below. Since the device class designator has been added after the original issuance of this drawing, device classes M and Q designators will not be included in the PIN and will not be marked on the device. Device class Device requirements documentation M Vendor self-certification
14、to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRC
15、UIT DRAWING SIZE A 77043 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL R SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style A 1/ GDFP5-F14 or CDFP6-F
16、14 14 Flat pack C GDIP1-T14 or CDIP2-T14 14 Dual-in-lineD GDFP1-F14 or CDFP2-F14 14 Flat pack X GDFP1-G14 14 Flat pack with gull wing leads 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, app
17、endix A for device class M. 1.3 Absolute maximum ratings. 2/ Supply voltage (+V) 32 V dc relative to ground Differential input voltage (VID) 32 V dc Input voltage (VIN) -0.3 V dc to +32 V dc Power dissipation (PD) . 750 mW 3/ Output short circuit to GND (one amplifier) . Continuous 4/ Storage temper
18、ature range . -65C to +150C Lead temperature (soldering, 10 seconds) . +300C Junction temperature (TJ) . +150C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA): Case C 103C/W Case D 126C/W Case X 176C/W Case 2 . 91C/W 1.4 Recommended operating
19、 conditions. Ambient operating temperature range (TA) . -55C to +125C _ 1/ Inactivate for new design. Acceptable only for use in equipment designed or redesigned on or before 29 November 1986. 2/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation
20、at the maximum levels may degrade performance and affect reliability. 3/ Dissipation is total of four amplifiers. Use external resistor to allow amplifier to saturate or reduce power dissipation in the circuit. 4/ Short circuits from output to +V can cause excessive heating and destruction. Maximum
21、output current is approximately 60 mA independent of magnitude of +V. Where V supply +15 V dc, continuous short circuits can exceed PDratings and cause destruction. Destructive dissipation can result from simultaneous shorts on all amplifiers. Provided by IHSNot for ResaleNo reproduction or networki
22、ng permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 77043 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL R SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards,
23、and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPA
24、RTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these d
25、ocuments are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein
26、, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL
27、-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535,
28、appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device c
29、lass M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the ele
30、ctrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical test
31、s for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the optio
32、n of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification
33、/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. Provided by IHSNot for ResaleNo reproduction or networking permitted without licen
34、se from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 77043 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL R SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C +V = 5.0 V dc Group A subgroups Device type Limits Unit unle
35、ss otherwise specified Min Max Input offset voltage VIO1/ 1 01 5 mV 2,3 7 1 02 2 2,3 4 Input offset current IIO+IIN= (-IIN), VCM= 0 V 1 01 30 nA 2,3 100 1 02 10 2,3 30 Input bias current IB+IINor -IIN, 2/ 1 01 -150 nA VCM= 0 V 2,3 -300 1 02 -50 2,3 -100 Input common mode voltage range VICR+V = 30 V
36、3/ 1 All 0 +V 1.5 V 2,3 0 +V 2.0 Large signal voltage gain AVD+V = 15 V (for large VOswing), RL 2 k, 4 All 50 V/mV VO= 1 V to 11 V 5,6 25 Output voltage swing VOUT+V = 30 V, RL 2 k 4,5,6 All 26 V VOH+V = 30 V, RL 10 k 27 VOLRL 10 k 20 mV Common mode rejection ratio CMRR +V = 30 V, TA= +25C 4 All 70
37、dB Amplifier to amplifier 3/ coupling 1 kHz, 20 kHz, TA= +25C 4 All 80 dB See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 77043 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISI
38、ON LEVEL R SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics continued. Test Symbol Conditions -55C TA +125C +V = 5.0 V dc Group A subgroups Device type Limits Unit unless otherwise specified Min Max Power supply rejection ratio PSRR TA= +25C 4 All 65 dB Output current so
39、urce IO+VIN= 1.0 V, -VIN= 0 V, 1 All 20 mA (source) +V = 15 V 2,3 10 Output current sink IO+VIN= 0 V, -VIN= +1.0 V, 1 All 10 mA (sink) +V = 15 V 2,3 5 +VIN= 0 V, -VIN= +1.0 V, VO= 200 mV 1 12 A Power supply current ICC1,2,3 All 1.2 mA +V = 30 V 1 3.0 2,3 4.0Short circuit current IOSVO= 0 V 1 All -60
40、 mA 1/ VO= 1.4 V dc, +V from 5 V dc to 30 V dc; and over full input common mode range ( 0 V dc to +V = -1.5 V dc ). 2/ The direction of the input current is out of the integrated circuit due to the PNP input state. This current is essentially constant, independent of output state, so no loading chan
41、ge exists on the input lines. 3/ If not tested, shall be guaranteed to specified limit in table I herein. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawi
42、ng (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved s
43、ource of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance a
44、s required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime-VA of change
45、of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review
46、 the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 49 (see
47、 MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 77043 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL R SHEET 7 DSCC FORM 2234 APR 97 Device types 01 and 02 Case outline
48、s A, C, D, X 2 Terminal number Terminal symbol 1 VO1 NC 2 -VIN1 VO1 3 +VIN1 -VIN1 4 +V +VIN1 5 +VIN2 NC 6 -VIN2 +V 7 VO2 NC 8 VO3 +VIN2 9 -VIN3 -VIN2 10 +VIN3 VO2 11 GND NC 12 +VIN4 VO3 13 -VIN4 -VIN3 14 VO4 +VIN3 15 - NC 16 - GND 17 - NC 18 - +VIN4 19 - -VIN4 20 - VO4 NC = No connection FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 77043 DLA LAND AND MARITIME COLUMBUS, OHIO
