1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Pg. 4, TABLE I. Change IIH2, IOS, and IO1e.g., IOS. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 80041 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3
2、990 REVISION LEVEL E SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documen
3、ts are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Compon
4、ent Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization
5、Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicabl
6、e laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produce
7、d by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordanc
8、e with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certifi
9、cation mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case out
10、lines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical
11、performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I.
12、 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built
13、 in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from
14、IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 80041 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 4 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Li
15、mits Unit Min Max High level output voltage VOHVCC= 4.5 V, VIL= 0.8 V, IOH= -2 mA 1, 2, 3 All 2.4 V VIH = 2.0 V IOH= -40 mA 1.8 Input clamp voltage VICVCC= 4.5 V, IIC= -12 mA, TA= +25C 1 All -1.5 V Low level output voltage VOLVCC= 4.5 V, VIL= 0.8 V, VIH= 2.0 V, IOL= 40 mA 1, 2, 3 All 0.5 V Output cl
16、amp voltage VICVCC= 4.5 V, IIC= -12 mA, TA= +25C 1 01 -1.5 V Low level input current IILVCC= 5.5 V, VIN= 0.4 V 1, 2, 3 All -1.6 mA High level input current IIH1VCC= 5.5 V, VIH= 2.4 V 1, 2, 3 All 40 A VCC= 5.5 V, VIH= 5.5 V 1.0 mA Output short circuit current IOSVCC= 5.5 V, TA= +125C 1/ 2 All -40 -15
17、0 mA Supply current ICCVCC= 5.5 V 1, 2, 3 All 90 mA Inhibited-state output leakage current IO1VCC= 5.5 V, VOUT= 0.4 V TA= +25C 1 All -40 A IO2VCC= 5.5 V, VOUT= 2.4 V TA= +25C +40 Propagation delay time, (low to high) tPLHVCC= 5.0 V, 2/, 3/ CL= 50 pF 9, 10, 11 All 2 42 ns Propagation delay time, (hig
18、h to low) tPHLVCC= 5.0 V, 2/, 3/ CL= 50 pF 9, 10, 11 All 2 42 ns Propagation delay time, (disable to high) tPZHVCC= 5.0 V, 2/ CL= 50 pF 9, 10, 11 All 2 38 ns See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICR
19、OCIRCUIT DRAWING SIZE A 80041 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - continued. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit
20、 Min Max Propagation delay time, (high to disable) tPHZVCC= 5.0 V, CL= 5 pF 2/, 4/ 9, 10, 11 All 2 21 ns Propagation delay time, (disable to low) tPZLVCC= 5.0 V, CL= 50 pF 2/ 9, 10, 11 All 2 47 ns Propagation delay time, (low to disable) tPLZVCC= 5.0 V, CL= 5 pF 2/, 4/ 9, 10, 11 All 2 38 ns Function
21、al testing See 4.3.1c 7 All 1/ Not more than one output should be shorted at a time. 2/ For subgroups 10 and 11 these limits shall be guaranteed, if not tested. 3/ For differential and single ended mode control. 4/ Testing can be done at 15 pF. 3.6 Certificate of compliance. A certificate of complia
22、nce shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of
23、MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DSCC-VA shall
24、 be required for any change that affects this drawing. 3.9 Verification and review. DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the
25、reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 80041 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 6 DSCC FORM 2234 APR 97 Device types 01 and 02 Case outlines E and F
26、2 Terminal number Terminal symbol 1 OUTPUT ENABLE B NC 2 OUTPUT ENABLE B OUTPUT ENABLE B 3 OUTPUT B2OUTPUT ENABLE B 4 INPUT B2OUTPUT B25 OUTPUT B1INPUT B26 INPUT B1NC 7 DIFF MODE CONTROL OUTPUT B18 GND INPUT B19 DIFF MODE CONTROL DIFF MODE CONTROL 10 INPUT A1GND 11 OUTPUT A1NC 12 INPUT A2DIFF MODE C
27、ONTROL 13 OUTPUT A2INPUT A114 OUTPUT ENABLE A OUTPUT A115 OUTPUT ENABLE A INPUT A216 VCCNC 17 - OUTPUT A218 - OUTPUT ENABLE A 19 - OUTPUT ENABLE A 20 - VCCFIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROC
28、IRCUIT DRAWING SIZE A 80041 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 7 DSCC FORM 2234 APR 97 Inputs Outputs Enable Differential / single ended mode control 1 2 1 2 L L L L L L L L L L L L H H H H L L X H H H L H L L X H L L H L L L H X H H L H L L H X L L H L H
29、 X X X X X Hi Z Hi Z X H X X X X Hi Z Hi Z Notes: X = dont care FIGURE 2. Truth table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 80041 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL
30、E SHEET 8 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quali
31、ty conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acqu
32、iring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table
33、 II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-883 including groups A, B, C, and D inspections. The follow
34、ing additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 4, 5, 6, and 8 in table I, method 5005 of MIL-STD-883 shall be omitted. c. Subgroup 7 shall include verification of the truth table. 4.3.2 Groups C and D inspections. a. End
35、-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the
36、 preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TA= +125C, minimum. (3) Test duration: 1,000 hours, except as permitted by metho
37、d 1005 of MIL-STD-883. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 80041 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 9 DSCC FORM 2234 APR 97 TABLE II. Electrical test requir
38、ements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Interim electrical parameters (method 5004) - Final electrical test parameters (method 5004) 1*, 2, 3, 9 Group A test requirements (method 5005) 1, 2, 3, 7, 9, (10, 11)* Groups C and D end-point el
39、ectrical parameters (method 5005) 1, 2, 3 * PDA applies to subgroup 1. * Subgroups 10 and 11, if not tested, shall be guaranteed to the limits specified in table I. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. 6. NOTES
40、 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a con
41、tractor-prepared specification or drawing. 6.3 Configuration control of SMDs. All proposed changes to existing SMDs will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.4 Record of users.
42、Military and industrial users shall inform Defense Supply Center Columbus (DSCC) when a system application requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of dra
43、wings covering microelectronics devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544. 6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43218-3990, or telephone (614) 692-0547. 6.6 Approved sources of supply. Approved sources of supply are listed in
44、MIL-HDBK-103. The vendors listed in MIL-HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DSCC-VA. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING
45、 BULLETIN DATE: 05-04-12 Approved sources of supply for SMD 80041 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or deletion of sources. The vend
46、ors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DSCC-VA. This information bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. DSCC maintains an online database of all current sources of supply at http:/ww
47、w.dscc.dla.mil/Programs/Smcr/. Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ Similar military specification PIN 2/ 8004101EA 3/ DS7831J/883B M38510/10406BEA 8004101FA 3/ DS7831W/883B M38510/10406BFA 80041012A 3/ DS7831JB/FKB 8004102EA 3V146 DS7832J/883B M38510/10407BE
48、A 3/ DS7832JB 8004102FA 3V146 DS7832W/883B M38510/10407BFA 80041022A 3V146 DS7832E/883B 3/ DS7832JB/FKB 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the
49、 vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 3/ Not available from an approved source of supply. Vendor CAGE Vendor name number and address 3V146 Rochester Electronics 10 Malcolm Hoyt Drive Newburyport, MA 01950 The info
