1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED D Add vendor CAGE F8859. Add device class V criteria. Correct data limits in paragraph 1.3. Add case outline X. Update boilerplate. Add table III, delta limits. Editorial changes throughout. - jak 00-06-21 Monica L. Poelking E Update the boilerplat
2、e paragraphs to current requirements as specified in MIL-PRF-38535. - jak 09-03-25 Thomas M. Hess Current CAGE code, 67268 REV SHET REV SHET REV STATUS REV E E E E E E E E E E E E E OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Donald R. Osborne STANDARD MICROCIRCUIT DRAWING CHE
3、CKED BY Robert P. Evans DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY N, A, Hauck AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 84-10-01 MICROCIRCUIT, DIGITAL, HIGH-SPEED CMOS, HEX IN
4、VERTER, MONOLITHIC SILICON AMSC N/A REVISION LEVEL E SIZE A CAGE CODE 14933 84098 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E192-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 84098 DEFENSE SUPPLY CENTER COLUMB
5、US COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are av
6、ailable and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following examples: For device classes M and Q 84098 01 C A Drawing number Device type (see 1.2.1) Cas
7、e outline(see 1.2.2) Lead finish(see 1.2.3)For device class V: 5962 - 84098 01 V C A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device cl
8、asses Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RH
9、A device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54HC04 Hex inverter 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device cla
10、ss Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as d
11、esignated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style B GDFP4-F14 14 Flat pack C GDIP1-T14 or CDIP2-T14 14 Dual-in-line D GDFP1-F14 or CDFP2-F14 14 Flat pack X CDFP3-F14 14 Flat pack 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The
12、lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 84098 DEFENSE SUPPLY CENTER COLUMBUS COLUMBU
13、S, OHIO 43218-3990 REVISION LEVEL E SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) . -0.5 V dc to +7.0 V dc DC input voltage range (VIN) . -0.5 V dc to VCC+0.5 V dc DC output voltage range (VOUT) -0.5 V dc to VCC+0.5 V dc Input clamp current (IIK) (VI
14、NVCC) 20 mA Output clamp current (IOK) (VOUTVCC) 20 mA Continuous output current (IOUT) (VOUT= 0.0 V to VCC) . 25 mA Continuous current through VCCor GND 50 mA Storage temperature range (TSTG) -65C to +150C Maximum power dissipation (PD) 500 mW 4/ Lead temperature (soldering, 10 seconds) +260C Therm
15、al resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) . +175C 1.4 Recommended operating conditions. 2/ 3/ Supply voltage range (VCC) . +2.0 V dc to +6.0 V dc Case operating temperature range (TC) -55C to +125C Input rise or fall time (tr, tf): VCC= 2.0 V 0 to 1000 ns VCC=
16、 4.5 V 0 to 500 ns VCC= 5.0 V 0.5 V . 0 to 400 ns 1/ Stresses above the absolute maximum rating may cause permanent damage to the device, Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The lim
17、its for the parameters specified herein shall apply over the full specified VCCrange and case temperature range of -55C to +125C. 4/ For TC= +100C to +125C, derate linearly at 12 mW/C. 5/ Maximum junction temperature shall not be exceeded except for allowable short duration burn-in screening conditi
18、ons in accordance with method 5004 of MIL-STD-883. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 84098 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 4 DSCC FORM 2234 APR 97 2. A
19、PPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEP
20、ARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-
21、HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
22、2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENT
23、S 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function
24、as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as s
25、pecified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 T
26、ruth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 4. Provided by IHSNot for ResaleNo reproductio
27、n or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 84098 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 5 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise
28、specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table I
29、I. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manu
30、facturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix
31、A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a
32、 certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in
33、MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the
34、 requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3
35、.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, D
36、SCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices cov
37、ered by this drawing shall be in microcircuit group number 36 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 84098 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISIO
38、N LEVEL E SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Test conditions 1/ -55C TC+125C unless otherwise specified VCCGroup A subgroups Limits Unit Min Max2.0 V 1.9 4.5 V 4.4 VIN= VIHminimum or VILmaximum IOH= -20 A 6.0 V 1, 2, 3 5.9 1 3.98 VIN= VIHminimu
39、m or VILmaximum IOH= -4.0 mA 4.5 V 2, 3 3.7 1 5.48 High level output voltage VOHVIN= VIHminimum or VILmaximum IOH= -5.2 mA 6.0 V 2, 3 5.2 V 2.0 V 0.1 4.5 V 0.1 VIN= VIHminimum or VILmaximum IOL= +20 A 6.0 V 1, 2, 3 0.1 1 0.26 VIN= VIHminimum or VILmaximum IOL= +4.0 mA 4.5 V 2, 3 0.40 1 0.26 Low leve
40、l output voltage VOLVIN= VIHminimum or VILmaximum IOL= +5.2 mA 6.0 V 2, 3 0.40 V 2.0 V 1, 2, 3 1.5 4.5 V 1, 2, 3 3.15 High level input voltage VIH2/ 6.0 V 1, 2, 3 4.2 V 2.0 V 1, 2, 3 0.3 4.5 V 1, 2, 3 0.9 6.0 V 1, 2, 3 1.2 Low level input voltage VIL2/ 2, 3 -1.0 V 1 2.0 Quiescent supply current ICCV
41、IN= VCCor GND IOUT= 0.0 A 6.0 V 2, 3 40.0 A 1 0.10 Input leakage current IINVIN= VCCor GND 6.0 V 2, 3 1.0 A Input capacitance CINTC= +25C VIN= 0.0 v See 4.4.1c 2.0 V to 6.0 V 4 10.0 pF Power dissipation capacitance CPDVIN= 0.0 V TC= +25C See 4.4.1c 6.0 V 4 20.0 pF See footnotes at end of table. Prov
42、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 84098 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued.
43、Test Symbol Test conditions 1/ -55C TC+125C unless otherwise specified VCCGroup A subgroups Limits Unit Min MaxFunctional tests See 4.4.1b 7, 8 L H 2.0 V 9 95.0 ns 4.5 V 9 19.0 ns TC= 25C CL= 50 pF minimum See figure 4 6.0 V 9 16.0 ns 2.0 V 10, 11 145.0 ns 4.5 V 10, 11 29.0 ns Propagation delay time
44、, mA to mY tPLH,tPHL 3/ TC= -55C and +125C CL= 50 pF minimum See figure 4 6.0 V 10, 11 25.0 ns 2.0 V 9 75.0 ns 4.5 V 9 15.0 ns TC= 25C CL= 50 pF minimum See figure 4 6.0 V 9 13.0 ns 2.0 V 10, 11 110.0 ns 4.5 V 10, 11 22.0 ns Transition time, high to low, low to high tTLH,tTHL 4/ TC= -55C and +125C C
45、L= 50 pF minimum See figure 4 6.0 V 10, 11 19.0 ns 1/ For a power supply of 5.0 V 10%, the worst case output voltages (VOHand VOL) occur for high-speed CMOS at 4.5 V. Thus, the 4.5 V values should be used when designing with this supply. Worst case leakage currents (IIN and ICC) occur for CMOS at th
46、e higher voltage, so the 6.0 V values should be used. Power dissipation capacitance (CPD), typically 20 pF per latch, determines the no load dynamic power consumption, PD= CPDVCC2f+ICCVCC, and the no load dynamic current consumption 2/ Tests shall be guaranteed if applied as a forcing function for V
47、OHand VOL. 3/ For propagation delay times VCC= 2.0 V and VCC= 6.0 V shall be guaranteed to the specified limits in table I. 4/ Transition time (tTLH, tTHL), if not tested, shall be guaranteed to the specified limits in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted wit
48、hout license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 84098 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Case outlines B, C, D and X 2 Terminal number Terminal symbol Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1A 1Y 2A 2Y 3A 3Y GND 4Y 4A 5Y 5A 6Y 6A VCCNC 1A 1Y 2A NC 2Y NC 3A 3Y GND NC 4Y 4A 5Y NC 5A NC 6Y 6A VCCNC = No internal connection FIGURE 1. Terminal connections. Provided by IHSNot for Resale
