1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add one vendor, CAGE U4637. Make changes to 1.2.2, 3.3, 4.2, 4.3, and editorial changes throughout. Make changes to table I and table II. 89-12-28 M. A. FRYE B Changes in accordance with N.O.R. 5962-R035-93. 93-04-06 M. A. FRYE C Changes in accor
2、dance with N.O.R. 5962-R176-96. 96-07-10 M. A. FRYE D Drawing updated to reflect current requirements. 01-11-01 R. MONNIN E Update drawing as part of 5 year review. rrp 06-03-23 R. MONNIN F Drawing updated to reflect current requirements of MIL-PRF-38535. -rrp 12-06-27 C. SAFFLE THE ORIGINAL FIRST S
3、HEET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV F F F F F F F F F F F OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY DONALD R. OSBORNE DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING
4、 IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY D. A. DiCENZO APPROVED BY N. A. HAUCK MICROCIRCUIT, LINEAR, SWITCHED-MODE POWER SUPPLY CONTROL CIRCUIT, MONOLITHIC SILICON DRAWING APPROVAL DATE 87-08-18 AMSC N/A REVISION LEVEL F SIZE A CAGE CODE 67268 596
5、2-86722 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E405-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86722 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 2 DSCC FORM 2234 APR 97 1.
6、 SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-86722 01 E A Drawing number Devi
7、ce type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 5560 Switched-mode power supply control circuit 1.2.2 Case outline(s). The case outline(s) are as des
8、ignated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage forced mode (VS) +18 V dc Suppl
9、y current fed mode (IS) . 30 mA Output transistor current (IC) . 40 mA Output transistor collector voltage (OUTPUT COLLECTOR pin) VCC+ 1.4 V Output transistor maximum emitter voltage (OUTPUT EMITTER pin) +5 V Maximum power dissipation (PD) 1 W Storage temperature range (TSTG) . -65C to +150C Lead te
10、mperature (soldering, 60 seconds) +300C Junction temperature (TJ) . +150C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 1.4 Recommended operating conditions. Ambient operating temperature range (TA) . -55C to +125C Provided by IHSNot for ResaleNo reproduction or networking permitted w
11、ithout license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86722 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handb
12、ooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF
13、 DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents
14、are available online at https:/assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of
15、 this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class
16、 level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance wit
17、h the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. T
18、hese modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be
19、as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Logic diagram. The logic diagram shall be as specified on figure 2. 3.3 E
20、lectrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroup
21、s specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. 3.5.1 Certification
22、/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. P
23、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86722 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 4 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol
24、 Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Reference section Internal reference voltage VREFIL= -7 mA 1 01 3.69 3.81 V 2,3 3.65 3.85 Internal zener reference VZIL= -7 mA, TA= +25C 1 01 7.8 8.8 V Oscillator section Frequency range fRR = 5
25、 k, fO= 20 kHz 4,5,6 01 50 100 k Hz Duty cycle range 2/ D.C. R = 5 k, fO= 20 kHz, TA= +25C 4 01 0 98 % MODULATOR section Modulation input current IIMODULATOR pin = 2 V 1,2,3 01 20 A Protection function section Input current at DUTY CYCLE CONTROL pin IIDUTY CYCLE CONTROL pin = 2 V 1,2,3 01 20 A Duty
26、cycle limit control at DUTY CYCLE CONTROL pin D.C. (For 50 % maximum duty cycle) 15 kHz to 50 kHz / (41 % of VZ), TA= +25C 4 01 40 60 % of duty cycle Low supply voltage protection threshold at VCCpin VCC(TH)TA= +25C 1 01 8 10.5 V Feedback loop protection trip threshold at FEEDBACK pin VTHTA= +25C 1
27、01 400 720 mV Pull up current at FEEDBACK pin IfbFEEDBACK pin = 2 V 1,2,3 01 -7 -35 A See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86722 DLA LAND AND MARITIME COLUMBUS, OHIO
28、43218-3990 REVISION LEVEL F SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Protection function section - continued DEMAGNETIZATION / OVERVOLT
29、AGE pin protection trip on threshold VTHTA= +25C 1 01 470 720 mV Input current at DEMAGNETIZATION / IIDEMAGNETIZATION / OVERVOLTAGE pin = 1 01 -10 A OVERVOLTAGE pin 0.25 V 2,3 -20 Duty cycle control at FEED FORWARD pin DCffFEED FORWARD pin = 2 VZ, TA= +25C 4 01 30 50 3/ Input current at FEED 4/ FORW
30、ARD pin IIFEED FORWARD pin = 16 V, 1 01 5 A VCC= 18 V 2,3 10 External synchronization section Voltage off at EXTERNAL SYNCHRONIZATION pin VOFFTA= +25C 1 01 0 0.8 V Voltage on at EXTERNAL SYNCHRONIZATION pin VONTA= +25C 1 01 2 VZV Sink current at EXTERNAL SYNCHRONIZATION pin IIEXTERNAL SYNCHRONIZATIO
31、N 1 01 -100 A pin = 0 V 2,3 -125 Remote section Voltage off at REMOTE pin VOFFTA= +25C 1 01 0 0.8 V Voltage on at REMOTE pin VONTA= +25C 1 01 2 VZV See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT D
32、RAWING SIZE A 5962-86722 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Remo
33、te section - continued Sink current at REMOTE ON/OFF pin IIREMOTE ON/OFF pin = 0 V 1 01 -100 A 2,3 -125 Current limiting section Current at CURRENT LIMITING pin I CURRENT LIMITING pin = 250 mV 1 01 -20 A 2,3 -40 Single pulse inhibit 2/ delay at CURRENT LIMITING pin TDInhibit delay time for 20 percen
34、t override at 40 mA IOUT, TA= +25C 9 01 0.8 s Trip levels: shut down, slow start VTHSDTA= +25C 1 01 0.500 0.700 V Trip levels: current limit VTHCLTA= +25C 1 01 0.400 0.560 V Error amplifier section Output voltage swing, high VOH1,2,3 01 6.2 9.5 V Output voltage swing, low VOL1 01 0.7 V 2,3 0.85 Open
35、 loop gain AO4 01 54 dB 5,6 50 Feedback resistor RfTA= +25C 1 01 10 k Output stage section Voltage at OUTPUT COLLECTOR pin VCE(SAT)IC= 40 mA, VE= 0 V, TA= +25C 1 01 0.5 V See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
36、STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86722 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type L
37、imits Unit Min Max Output stage section - continued Maximum voltage at 2/ OUTPUT EMITTER pin VE(MAX)IE= -200 mA, VC= 12 V, TA= +25C 1 01 5 V Supply current at VCCpin ICCIZ= 0 V, voltage forced 1 01 10 mA 2,3 15 Supply voltage at VCCpin VCCICC= 10 mA current fed, TA= +25C 1 01 20 23 V ICC= 30 mA curr
38、ent fed, TA= +25C 20 30 1/ Unless otherwise specified, VCC= 12 V. 2/ If not tested, shall be guaranteed to the limits specified in table I herein. 3/ Percentage of original duty cycle 4/ Does not include current for timing resistor or capacitor. 3.6 Certificate of compliance. A certificate of compli
39、ance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets t
40、he requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of chan
41、ge to DLA Land and Maritime -VA shall be required for any change that affects this drawing. 3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offsh
42、ore documentation shall be made available onshore at the option of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86722 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 8
43、DSCC FORM 2234 APR 97 Device type 01 Case outline E Terminal number Terminal symbol 1 VCC2 VZ3 FEEDBACK 4 GAIN 5 MODULATOR 6 DUTY CYCLE CONTROL 7 RT8 CT9 EXTERNAL SYNCHRONIZATION 10 REMOTE ON / OFF 11 CURRENT LIMITING 12 GND 13 DEMAGNETIZATION / OVERVOLTAGE 14 OUTPUT (EMITTER) 15 OUTPUT (COLLECTOR)
44、16 FEED FORWARD FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86722 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 9 DSCC FORM 2234 APR 97 FIGURE 2. L
45、ogic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86722 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 10 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection.
46、 Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a.
47、 Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, bi
48、ases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4.3 Quality conformance inspection. Quality conformance inspection shall be in ac
