1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Drawing updated to reflect current requirements. - ro 06-08-16 R. MONNIN B Update drawing as part of 5 year review. -jt 12-04-03 C. SAFFLE CURRENT CAGE CODE 67268 THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV
2、STATUS REV B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY DONALD R. OSBORNE DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTME
3、NT OF DEFENSE CHECKED BY D. A. DiCENZO APPROVED BY N. A. HAUCK MICROCIRCUIT, LINEAR, DUAL, HIGH-SPEED, VOLTAGE COMPARATOR, MONOLITHIC SILICON DRAWING APPROVAL DATE 87-02-02 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 14933 5962-86878 SHEET 1 OF 10 DSCC FORM 2233 APR 97 5962-E258-12 Provided by IHSNot
4、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86878 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-88
5、3 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-86878 01 C X Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1
6、Device type. The device type identify the circuit function as follows: Device type Generic number Circuit function 01 TL514 Dual differential voltage comparator 1.2.2 Case outline. The case outline are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Pack
7、age style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. 1/ Positive supply voltage . +14 V dc Negative supply voltage -7.0 V dc Differential input voltage (VID) 5 V Input voltage . 7 V Peak outp
8、ut current ( TW 1 second ) . 10 mA Strobe voltage 6 V Storage temperature range . -65C to +150C Power dissipation (PD) total package . 600 mW 2/ Lead temperature (soldering, 10 seconds) . +300C Junction temperature (TJ) . +150C Thermal resistance, junction-to-ambient (JC) . See MIL-STD-1835 1.4 Reco
9、mmended operating conditions. Ambient operating temperature range (TA) . -55C to +125C _ 1/ All voltage values, except differential voltages, are with respect to the network ground terminal. 2/ Above +25C derate linearly at 11.1 mW/C. Provided by IHSNot for ResaleNo reproduction or networking permit
10、ted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86878 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and
11、handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTME
12、NT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these docum
13、ents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, t
14、he text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non
15、-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in acco
16、rdance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the
17、 device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions
18、 shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections and functions diagram. The terminal connections and functions diagram shall be as specified on figure 1. 3.2.3 Output response gra
19、ph. The output response graph shall be as specified on figure 2. 3.2.4 Strobe release time graph. The strobe release time graph shall be as specified on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specifie
20、d in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. Provided by IHSNot for ResaleNo reproducti
21、on or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86878 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C VCC= +12 V, VEE
22、= -6 V Group A subgroups Device type Limits Unit unless otherwise specified Min Max Input offset voltage VIORS 200 , VO= 1.4 V 1 01 2.0 mV RS 200 , VO= 1.0 V 2 3.0 RS 200 , VO= 1.8 V 3 3.0 Input offset current IIORS 200 , VO= 1.4 V 1 01 3.0 A RS 200 , VO= 1.0 V 2 3.0 RS 200 , VO= 1.8 V 3 7.0 Input b
23、ias current IIBVO= 1.4 V 1 01 15 A VO= 1.8 V 3 25 Open loop voltage gain AVOLVO= 0 to 2.5 V, no load 4 01 1250 V/mV 5,6 1000 Differential voltage range VIDRTA= +25C 1 01 5 V High level output voltage VOHVID= 5 mV, IOH= 0 1,2,3 01 5 V VID= 5 mV, IOH= -5 mA 2.5 Low level output voltage VOLVID -5 mV, I
24、OL= 0, VSTROBE= 0.3 V 1,2,3 01 -1.0 0 V VID= 5 mV, IOL= 0, VSTROBE= 0.3 V -1.0 0 Low level output current IOLVID= -5 mV, VO= 0 1 01 0.2 mA 2 0.5 3 1 Input common mode range VICRVEE= -7 V 1,2,3 01 5 V Common mode rejection range CMRR RS 200 1,2,3 01 80 dB Strobe low level current IIL(S)VSTROBE= -100
25、mV, TA= +25C, VID= 5 mV 1 01 -2.5 mA Strobe high level current IIH(S)VSTROBE= 5 V, TA= +25C, VID= -5 mV 1 01 +100 A See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86878 DLA LAN
26、D AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA +125C VCC= +12 V, VEE= -6 V Group A subgroups Device type Limits Unit unless otherwise specified Min Max Total power suppl
27、y current ICCVID= -5 mV, no load 1,2,3 01 18 mA (both comparators) IEE-14 Total power consumption PDVID= -5 mV, no load 1,2,3 01 300 mW (both comparators) Response time RL= infinite, 1/ CL= 5 pF, TA= +25C 9 01 80 ns Strobe release time RL= infinite, 2/ CL= 5 pF, TA= +25C 9 01 25 ns 1/ The response t
28、ime specified is for a 100 mV input step with 5 mV overdrive. 2/ Input bias conditions are selected to produce an output voltage of 1.4 V. A 5 mV overdrive is then added to the input bias voltage to produce an output voltage that rises above 1.4 V. The time interval is measured from the 50 % point o
29、f the strobe voltage curve to the point where the overdriven output voltage crosses the 1.4 V level. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For pack
30、ages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38
31、535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed
32、 as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirement
33、s herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be required for any change
34、 that affects this drawing. 3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option
35、of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86878 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 FIGURE 1. Terminal connections and functio
36、ns diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86878 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 NOTE: VO= 1.8 V at TA= -55C, VO= 1.4 V at TA= +
37、25C, and VO= 1 V at TA= +125C. These output voltage levels were selected to approximate the logic threshold voltages of the types of digital logic circuits these comparators are intended to drive. FIGURE 2. Output response. Provided by IHSNot for ResaleNo reproduction or networking permitted without
38、 license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86878 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 NOTE: VO= 1.8 V at TA= -55C, VO= 1.4 V at TA= +25C, and VO= 1 V at TA= +125C. These output voltage levels were selected to approximate
39、the logic threshold voltages of the types of digital logic circuits these comparators are intended to drive. FIGURE 3. Strobe release time. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86878 DLA LAND AND M
40、ARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and
41、 shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and
42、 shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electric
43、al test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-883 includ
44、ing groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 7, 8, 10 and 11 in table I, method 5005 of MIL-STD-883 shall be omitted. 4.3.2 Groups C and D inspections. a. End-point elec
45、trical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing o
46、r acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TA= +125C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MI
47、L-STD-883. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86878 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 10 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-STD
48、-883 test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Interim electrical parameters (method 5004) 1 Final electrical test parameters (method 5004) 1*, 2, 3, 4, 9 Group A test requirements (method 5005) 1, 2, 3, 4, 5, 6, 9 Groups C and D end-point electrical parameters (method 5005) 1, 2, 3 * PDA applies to subgroup 1. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-3853
