1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add one vendor, CAGE 24355. Make changes to table I and editorial changes throughout. Change drawing CAGE to 67268. 90-06-26 M. L. POELKING B Drawing updated to reflect current requirements. - ro 02-06-12 R. MONNIN C Five year review requirement.
2、 - ro 07-10-16 R. HEBER D Update drawing to reflect current MIL-PRF-38535 requirements. - ro 13-01-22 C. SAFFLE CURRENT CAGE CODE 67268 THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 PMIC N/A PREPARED BY
3、DONALD R. OSBORNE DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY D. A. DiCENZO APPROVED BY N. A. HAUCK MICROCIRCUIT, LINEAR, PREC
4、ISION VOLTAGE REFERENCE, +10 VOLT, MONOLITHIC SILICON DRAWING APPROVAL DATE 87-03-31 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 14933 5962-86882 SHEET 1 OF 8 DSCC FORM 2233 APR 97 5962-E200-13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD
5、MICROCIRCUIT DRAWING SIZE A 5962-86882 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, append
6、ix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-86882 01 X A Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type
7、Generic number Circuit function 01 AD581S, LH0070-0 Precision 10-volt voltage reference 02 AD581T, LH0070-1 Precision 10-volt voltage reference 03 AD581U, LH0070-2 Precision 10-volt voltage reference 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline
8、 letter Descriptive designator Terminals Package style X See figure 1 3 Can 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage 40 V dc Input-output voltage differential 35 V dc Output short circuit duration VIN= 35 V . 10 sec
9、onds VIN 20 V . Indefinite Trim pin to ground voltage: Positive . Equal to VOUTNegative -20 V Storage temperature range . -65C to +150C Power dissipation total package at +25C 600 mW Lead temperature (soldering, 10 seconds) . +300C Junction temperature (TJ) . +150C Thermal resistance, junction-to-ca
10、se (JC) . 100C/W Thermal resistance, junction-to-ambient (JA) 200C/W 1.4 Recommended operating conditions. Ambient operating temperature range (TA) . -55C to +125C Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5
11、962-86882 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. U
12、nless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuit
13、s. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from
14、 the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however,
15、 supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this dr
16、awing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity
17、approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A
18、 “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case o
19、utline. The case outline shall be in accordance with 1.2.2 herein and on figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as
20、specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in a
21、ccordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not markin
22、g the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535
23、 to identify when the QML flow option is used. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86882 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 TABLE I. Ele
24、ctrical performance characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output voltage VRTA= +25C 1 01,02 9.990 10.010 V 03 9.995 10.005 1,2,3 01,02 9.970 10.030 03 9.980 10.020 Output voltage change with temperature V
25、R/ T 2/ 01 0.2 % 02 0.1 03 0.04 Line regulation VR/ VIN13 V VIN 33 V, 1 01,02 0.1 % TA= 25C 03 0.03 Input voltage range VIN1,2,3 All 11.4 40 V Load regulation VR/ IOUT0 mA IOUT 5 mA 1,2,3 All 0.03 % Quiescent current IQ13 V VIN 33 V 1,2,3 All 5 mA Change in quiescent current IQ/ VINVIN= 20 V, from 1
26、3 V to 33 V 1,2,3 All 1.5 mA Output resistance RO0 mA IOUT 5 mA 1,2,3 All 0.6 1/ Unless otherwise specified, VIN= 15 V, RL= 10 k, -55C TA +125C. 2/ Output voltage change with temperature is guaranteed from 25C to +85C. 3.6 Certificate of compliance. A certificate of compliance shall be required from
27、 a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-
28、38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DLA Land and Maritime
29、 -VA shall be required for any change that affects this drawing. 3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be
30、made available onshore at the option of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86882 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 Symbo
31、l Inches Millimeters Note Min Max Min Max A .165 .185 4.19 4.70 b1 .016 .019 0.41 0.48 D .340 .370 8.64 9.40 D1 .305 .335 7.75 8.51 e .200 BSC 5.08 BSC 1 e1 .100 BSC 2.54 BSC 1 L .500 - 12.70 - k .028 .034 0.71 0.86 k1 .026 .045 0.66 1.14 45 45 NOTES: 1. Leads having a maximum diameter of 0.019 (0.4
32、8 mm) measured in gauging plane 0.054 0.001 (1.37 0.03 mm) below the base plane of the product shall be within 0.007 (0.18 mm) of their true position relative to the maximum tab width. 2. The U.S. government preferred system of measurement is the metric SI system. However, since this item was origin
33、ally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROC
34、IRCUIT DRAWING SIZE A 5962-86882 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-
35、86882 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004
36、 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revisi
37、on level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interi
38、m and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 o
39、f MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 4, 5, 6, 7, 8, 9, 10, and 11 in table I, method 5005 of MIL-STD-883 shall be omitted. 4.3.2 Groups C and
40、 D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be
41、 made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TA= +125C, minimum. (3) Test duration: 1,000 hours, except
42、 as permitted by method 1005 of MIL-STD-883. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING
43、SIZE A 5962-86882 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Interim electrical parameters (method 5004) 1 Final
44、electrical test parameters (method 5004) 1*, 2, 3 Group A test requirements (method 5005) 1, 2, 3 Groups C and D end-point electrical parameters (method 5005) 1 * PDA applies to subgroup 1. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microc
45、ircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-prepared specification or drawing. 6.3 Configuration control of SMDs. All proposed changes to
46、existing SMDs will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires co
47、nfiguration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962) should contact DLA Land and Maritim
48、e-VA, telephone (614) 692-8108. 6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 43218-3990, or telephone (614) 692-0540. 6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103 and QML-38535. The vendors listed in MIL-HDBK-103 and QML-38535 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DLA Land and Maritime-VA. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-
