1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Redraw to update drawing to current MIL-PRF- 38535 requirements. - drw 01-12-17 Raymond Monnin B Redrawn. Update paragraphs to MIL-PRF-38535 requirements. - drw 13-08-02 Charles F. Saffle THE FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHE
2、ET REV SHEET REV STATUS REV B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 PMIC N/A PREPARED BY Marcia B. Kelleher DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE
3、 DEPARTMENT OF DEFENSE CHECKED BY D. A. DiCenzo APPROVED BY N. A. Hauck MICROCIRCUITS, LINEAR, MOSFET DRIVER, DUAL POWER, MONOLITHIC SILICON DRAWING APPROVAL DATE 87-09-03 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-87660 SHEET 1 OF 8 DSCC FORM 2233 APR 97 5962-E512-13 Provided by IHSNot f
4、or ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87660 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883
5、compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-87660 01 G C Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 De
6、vice type. The device type identifies the circuit function as follows: Device type Generic number Circuit function 01 ICL7667 Dual power MOSFET driver 1.2.2 Case outlines. The case outlines are as designated in MIL-STD-1835 as follows: Outline letter Descriptive designator Terminals Package style G
7、MACY1-X8 8 Can P GDIP1-T8 or CDIP2-T8 8 Dual-in-line 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage V+ to V- 15 V Input voltage . (V- = -0.3 V) to (V+ = +0.3 V) Power dissipation (PD): Cases G and P 500 mW Derating factor
8、: Case G 6.7 mW/C above +50C Case P 6.7 mW/C above +50C Storage temperature range . -65C to +150C Lead temperature (soldering, 10 seconds) . +300C Thermal resistance (JC): Cases G and P See MIL-STD-1835 Junction temperature (TJ) . +175C 1.4 Recommended operating conditions. Ambient operating tempera
9、ture range -55C to +125C VCC4.5 V to 15 V Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87660 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOC
10、UMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DE
11、FENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - Li
12、st of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/quicksearch.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. I
13、n the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. T
14、he individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has bee
15、n granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications t
16、o the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Des
17、ign, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be
18、as specified on figure 1. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test req
19、uirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87660 DLA LAND AND MARITIME COLUMBUS, O
20、HIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Logic 1 input voltage VIHVCC= 4.5 V 1, 2, 3 01 2.0 V VCC= 15 V 2.0 Logic 0
21、input voltage VILVCC= 4.5 V 1 01 0.8 V 2, 3 0.5 VCC= 15 V 1, 2, 3 0.8 Input current IILVCC= 15 V, VIN= 0 V and 15 V 1, 2, 3 01 -0.1 0.1 A Output voltage high VOHVCC= 4.5 V and 15 V 1 01 VCC0.05 V 2, 3 VCC0.1 Output voltage low VOLVCC= 4.5 V and 15 V 1 01 0.05 V 2, 3 0.1 Output resistance ROUTVIN= VI
22、L, IOUT= -10 mA, 1 01 10 VCC= 15 V 2, 3 12 VIN= VIH, IOUT= 10 mA, 1 12 VCC= 15 V 2, 3 13 Power supply current ICCVCC= 15 V, VIN= 3 V both 1 01 7 mA inputs 2, 3 8 VCC= 15 V, VIN= 0 V both 1 400 A inputs 2, 3 400 Delay time tD2See figure 2 9 01 50 ns 10 11 60 Rise time tRSee figure 2 9 01 30 ns 10 11
23、40 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87660 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - contin
24、ued. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Fall time tF See figure 2 9 01 30 ns 10, 11 40 Delay time tD1See figure 2 9 01 30 ns 10, 11 40 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part s
25、hall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/com
26、pliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 C
27、ertificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply sh
28、all affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.
29、 3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be required for any change that affects this drawing. 3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers faci
30、lity and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87660 DLA LAND AND MARITIME CO
31、LUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 Device type 01 Case outline G P Terminal number Terminal symbol 1 OUT A NC 2 NC IN A 3 IN A V- 4 V- IN B 5 IN B OUT B 6 NC V+ 7 OUT B OUT A 8 V+ NC NC = No connection FIGURE 1. Terminal connections. FIGURE 2. Timing waveforms. Pr
32、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87660 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. Sampling and ins
33、pection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, me
34、thod 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and
35、power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the di
36、scretion of the manufacturer. TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Interim electrical parameters (method 5004) 1 Final electrical test parameters (method 5004) 1*, 2, 3 Group A test requirements (method
37、 5005) 1, 2, 3, 9, 10, 11 Groups C and D end-point electrical parameters (method 5005) 1 * PDA applies to subgroup 1. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-883 including groups A, B, C, and D inspections. The following a
38、dditional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 4, 5, 6, 7, and 8 in table I, method 5005 of MIL-STD-883 shall be omitted. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STAND
39、ARD MICROCIRCUIT DRAWING SIZE A 5962-87660 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 o
40、f MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissi
41、pation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TA= +125C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with
42、 MIL-PRF-38535, appendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the
43、same generic device covered by a contractor-prepared specification or drawing. 6.3 Configuration control of SMDs. All proposed changes to existing SMDs will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Ch
44、ange Proposal. 6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires configuration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this list will be used for coordination and d
45、istribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962) should contact DLA Land and Maritime-VA, telephone (614) 692-8108. 6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 43218-3990, or telephone (61
46、4) 692-0540. 6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103 and QML-38535. The vendors listed in MIL-HDBK-103 and QML-38535 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DLA Land and Maritime-
47、VA. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 13-08-02 Approved sources of supply for SMD 5962-87660 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and
48、 QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DLA Land and Maritime-VA. This information bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. DLA Land and Maritime maintains an online database of all current sources of supply at http:/www.landandmaritime.dla.mil/Programs/Smcr/. Standard microcircuit drawing PIN 1/ Ven
