1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Make changes to 1.3, 6.6, and table I. Editorial changes throughout. 89-08-03 M. A. Frye B Update drawing to current requirements. Editorial changes throughout. - drw 06-10-20 Raymond Monnin THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLA
2、CED. REV SHET REV SHET REV STATUS REV B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 PMIC N/A PREPARED BY Rick Officer DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Raymond Monnin COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEP
3、ARTMENTS APPROVED BY Michael A. Frye MICROCIRCUIT, LINEAR, DUAL RS232 AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 88-01-27 TRANSCEIVERS, MONOLITHIC SILICON AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-87666 SHEET 1 OF 8 DSCC FORM 2233 APR 97 5962-E037-07 Provided by IHSN
4、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87666 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for
5、 MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-87666 01 V A Drawing number Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.
6、3)1.2.1 Device types. The device types identify the circuit function as follows: Device type Generic number Circuit function 01 LT1080 RS232 transceiver with shutdown, bipolar 02 LT1081 RS232 transceiver, bipolar 1.2.2 Case outlines. The case outlines are as designated in MIL-STD-1835 as follows: Ou
7、tline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line V GDIP1-T18 or CDIP2-T18 18 Dual-in-line 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage (VCC) +6 V dc Positive supply vo
8、ltage (V+) +12 V dc Negative supply voltage (V-) -12 V dc Driver input voltage V- to V+ Receiver input voltage . -30 V dc to +30 V dc On-off input voltage (pin 18), device type 01 only GND to +12 V dc Driver output voltage V- +30 V dc to V+ -30 V dc Receiver output voltage . -0.3 V dc to VCC+ 0.3 V
9、dc Short circuit duration, (V+), device type 01 only. 30 seconds Short circuit duration, (V-), device type 01 only . 30 seconds Short circuit duration, driver and receiver outputs Continuous Power dissipation (PD) . 500 mW 1/, 2/ Thermal resistance, junction-to-case (JC). See MIL-STD-1835 Thermal re
10、sistance, junction-to-ambient (JA): Case E . 100C/W Case V . 100C/W Maximum junction temperature (TJ). +150C Storage temperature range -65C to +150C Lead temperature (soldering, 10 seconds) +300C 1.4 Recommended operating conditions. Supply voltage (VCC) +4.5 V dc to +5.5 V dc Ambient operating temp
11、erature range (TA) -55C to +125C _ 1/ Must withstand the added PDdue to short circuit test; e.g., IOS. 2/ Derate at 9.5 mW/C above TA= +70C.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87666 DEFENSE SUPPLY
12、 CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise
13、 specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835
14、 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.da
15、ps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this
16、document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Produc
17、t built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qu
18、alifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as d
19、escribed herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and he
20、rein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
21、 as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be
22、in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not ma
23、rking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-3
24、8535 to identify when the QML flow option is used. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87666 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97
25、 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C +4.5 V dc VCC +5.5 V dc VON-OFF= 3.0 V dc Group A subgroups Device type Limits Unit unless otherwise specified Min Max Output voltage swing VOUTPositive 1, 2, 3 All 5.0 V Negative TR1, TR2 each loaded with 3 k to
26、GND -5.0 Low level input voltage VILVOUT= high 1, 2, 3 All 0.8 V High level input voltage VIHVOUT= low 1, 2, 3 All 2.0 V Logic input current high IIHVIN 2.0 V 1, 2, 3 All 200 A Logic input current low IILVIN 0.8 V 1, 2, 3 All 200 A Output short circuit current (transmitter) 1/ IOSTVOUT= 0 V Sourcing
27、 current 1 All 7 mA Sinking current -7 Output leakage current (transmitter) 1/ IOZTVOUT= 30 V 1, 2, 3 01 100 A Slew rate S.R. RL= 3 k, CL= 51 pF, TA= +25C 4 All 4 30 V/s RS-232 input threshold low VTLVOUT= high 1, 2, 3 All 0.2 V RS-232 input threshold high VTHVOUT= high 1, 2, 3 All 3.0 V RS-232 inpu
28、t hysteresis VH1. 2. 3 All 0.1 1.0 V Receiver input resistance RITA= +25C 1 All 3.0 7.0 k Receiver output high voltage VOHIOUT= 160 A, VCC= 5 V 1, 2, 3 All 3.5 V Receiver output low voltage VOLIOUT= -1.6 mA 1, 2, 3 All 0.4 V Output short circuit current (receiver) IOSRVOUT= VCC, sinking current 1 Al
29、l -10 mA OUT= 0 V, sourcing current 0.6 Output leakage current (receiver) 1/ IOZR0 V VOUT VCC1, 2, 3 01 10 A See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87666 DEFENSE SUPPLY
30、 CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - continued. Test Symbol Conditions -55C TA +125C +4.5 V dc VCC +5.5 V dc VON-OFF= 3.0 V dc Group A subgroups Device type Limits Unit unless otherwise specified M
31、in Max Supply current ICCOutputs unloaded 1, 2, 3 All 22 mA V+ output voltage 2/ VO+ IOUT= 0 mA 1 All 8.0 V OUT= 10 mA 7.0 IOUT= 15 mA 6.5 V- output voltage 2/ VO- IOUT= 0 mA 1 All -7.5 V OUT= -10 mA -5.5 IOUT= -15 mA -5.0 Supply leakage current 1/, 2/ ICCZShutdown mode 1 01 100 A ON-OFF pin current
32、 1/, 2/ ISHUT0 V VON-OFF 5 V 1 01 -15 80 A 1/ VON-OFF= 0.4 V for -55C TA+100C, and VON-OFF= 0.2 V for +100C TA+125C. 2/ VCC= 5 V, external loading of V+ and V- equals zero, and the driver outputs are low (inputs high). Provided by IHSNot for ResaleNo reproduction or networking permitted without lice
33、nse from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87666 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 Device type 01 02 Case outline V E Terminal number Terminal symbol 1 NC C1+ 2 C1+ V+ 3 V+ C1- 4 C1- C2+ 5 C2+ C2- 6 C2- V- 7 V- TR2
34、 OUT 8 TR2 OUT REC 2 IN 9 REC 2 IN REC 2 OUT 10 REC 2 OUT TR2 IN 11 TR2 IN TR1 IN 12 TR1 IN REC 1 OUT 13 REC 1 OUT REC 1 IN 14 REC 1 IN TR1 OUT 15 TR1 OUT GND 16 GND VCC17 VCC- - - 18 ON- OFF - - - FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted w
35、ithout license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87666 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed a
36、s an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certif
37、icate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing. 3.9 Verifi
38、cation and review. DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 4. VERIFICATION 4.1 Sampling and inspection. Sampling a
39、nd inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in te
40、st, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases
41、, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at
42、the discretion of the manufacturer. TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Interim electrical parameters (method 5004) 1 Final electrical test parameters (method 5004) 1*, 2, 3, 4 Group A test requirement
43、s (method 5005) 1, 2, 3, 4 Groups C and D end-point electrical parameters (method 5005) 1, 2, 3 * PDA applies to subgroup 1. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87666 DEFENSE SUPPLY CENTER COLUMBU
44、S COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group
45、 A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 5, 6, 7, 8, 9, 10, and 11 in table I, method 5005 of MIL-STD-883 shall be omitted. 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test c
46、onditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs,
47、 biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TA= +125C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging sha
48、ll be in accordance with MIL-PRF-38535, appendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-prepared specification or drawing. 6.3 Configuration control of SMDs. All proposed changes to existing SMDs will be coordinated with the users o
