1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R097-98. 98-04-24 Monica L. Poelking B Add vendor CAGE F8859. Add device class V criteria. Editorial changes throughout. - gap 99-12-14 Raymond Monnin C Add case outline X. Add delta limits for class V devices.
2、 Editorial changes throughout - gap. 00-07-31 Raymond Monnin D Update boilerplate to MIL-PRF-38535 requirements. Make change to VOHdelta limit in table III. - jak 01-01-10 Thomas M. Hess E Add section 1.5, radiation features. Make corrections to the waveforms in figure 5. Update boilerplate to MIL-P
3、RF-38535 requirements and to include radiation hardness assured requirements. Editorial changes throughout. - LTG 05-04-14 Thomas M. Hess F Update radiation features in 1.5 and add SEP table IB. Update boilerplate to current MIL-PRF-38535 requirements. Editorial changes throughout. jak 11-12-05 Thom
4、as M. Hess G Update dimensions of case outline X to figure 1. - LTG 12-08-23 Thomas M. Hess REV SHEET REV G G G G G SHEET 15 16 17 18 19 REV STATUS REV G G G G G G G G G G G G G G OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Greg A. Pitz DLA LAND AND MARITIME COLUMBUS, OHIO
5、43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A CHECKED BY D. A. DiCenzo APPROVED BY Michael A. Frye MICROCIRCUIT, DIGITAL, ADVANCED CMOS, OCTAL D-TYPE FLIP-FLOP WITH TH
6、REE-STATE OUTPUTS, MONOLITHIC SILICON DRAWING APPROVAL DATE 87-12-08 REVISION LEVEL G SIZE A CAGE CODE 67268 5962-87694 SHEET 1 OF 19 DSCC FORM 2233 APR 97 5962-E419-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZ
7、E A 5962-87694 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case
8、 outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following examples. For device classes M and Q: 5962 F 87694 01 X A
9、Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Case outline (see 1.2.4) Lead finish (see 1.2.5) / / Drawing number For device class V: 5962 F 87694 01 V X A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Ca
10、se outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appe
11、ndix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54AC374 Octal D-type flip-flop with three-state out
12、puts 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as listed below. Since the device class designator has been added after the original issuance of this drawing, device classes M and Q designators will not be included in the PIN
13、 and will not be marked on the device. Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 Pr
14、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87694 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated
15、in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 Dual-in-line S GDFP2-F20 or CDFP3-F20 20 Flat pack X See figure 1 20 Flat pack 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in M
16、IL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) -0.5 V dc to +7.0 V dc DC input voltage range (VIN) -0.5 V dc to VCC + 0.5 V dc DC output voltage range (VOUT) . -0.5 V dc to VCC+ 0.5 V dc Clamp
17、 diode current (IIK, IOK) . 20 mA DC output current (per output pin) . 50 mA DC VCCor GND current (per output pin) 25 mA 4/ Maximum power dissipation (PD) . 500 mW Storage temperature range (TSTG) . -65C to +150C Lead temperature (soldering, 10 seconds) +260C Thermal resistance, junction-to-case (JC
18、) . See MIL-STD-1835 Junction temperature (TJ) +175C 5/ 1.4 Recommended operating conditions. 2/ 3/ 6/ Supply voltage range (VCC) +2.0 V dc to +6.0 V dc Input voltage range (VIN) +0.0 V dc to VCCOutput voltage range (VOUT). +0.0 V dc to VCCCase operating temperature range (TC) . -55C to +125C Input
19、rise or fall time rate (t/V): VCC= 3.6 V to 5.5 V . 0 to 8 ns/V 1.5 Radiation features. Device type 01: Maximum total dose available (dose rate = 50 300 rads (Si)/s) . 300 krads (Si) Single event phenomenon (SEP): effective LET, no SEL (see 4.4.4.2) 93 MeV-cm2/mg 7/ effective LET, no SEU (see 4.4.4.
20、2) . 93 MeV-cm2/mg 7/ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits for the parameters speci
21、fied herein shall apply over the full specified VCCrange and case temperature range of -55C to +125C. 4/ For devices with multiple VCCor GND pins, this value represents the total VCCor GND current. 5/ Maximum junction temperature shall not be exceeded except for allowable short duration burn-in scre
22、ening conditions in accordance with method 5004 of MIL-STD-883. 6/ Operation from 2.0 V dc to 3.0 V dc is provided for compatibility with data retention and battery back-up systems. Data retention implies no input transition and no stored data loss with the following conditions: VIH 70% VCC, VIL 30%
23、 VCC, VOH 70% VCC -20A, VOL 30% VCC 20 A. 7/ These limits were obtained during technology characterization and qualification, and are guaranteed by design or process, but not production tested unless specified in the customer through the purchase order or contract. Provided by IHSNot for ResaleNo re
24、production or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87694 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following
25、 specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, Gene
26、ral Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit D
27、rawings. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following document(s) form a part of this document to th
28、e extent specified herein. Unless otherwise specified, the issues of these documents cited in the solicitation or contract. JEDEC SOLID STATE TECHNOLOGY ASSOCIATION (JEDEC) JEDEC Standard No. 20 - Standard for Description of 54/74ACXXXXX and 54/74ACTXXXXX Advanced High-Speed CMOS Devices. (Copies of
29、 these documents are available online at http:/www.jedec.org or from JEDEC Solid State Technology Association, 3103 North 10thStreet, Suite 240-S Arlington, VA 22201). ASTM INTERNATIONAL (ASTM) ASTM F1192 - Standard Guide for the Measurement of Single Event Phenomena (SEP) Induced by Heavy Ion Irrad
30、iation of Semiconductor Devices. (Copies of this document is available online at http:/www.astm.org/ or from ASTM International, P. O. Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959). (Non-Government standards and other publications are normally available from the organizations th
31、at prepare or distribute the documents. These documents may also be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Not
32、hing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modifie
33、d in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and
34、 as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. Provided by IHSNot for ResaleNo reproduc
35、tion or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87694 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 5 DSCC FORM 2234 APR 97 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 and figure 1 herein. 3.2.2
36、 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Truth table. The truth table shall be as specified on figure 3. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 4. 3.2.5 Switching waveforms and test circuit. The switching waveforms and t
37、est circuit shall be as specified on figure 5. 3.2.6 Radiation exposure circuit. The radiation exposure circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. 3.3 Electrical performance ch
38、aracteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table IA and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The el
39、ectrical test requirements shall be the subgroups specified in table IIA. The electrical tests for each subgroup are defined in table IA. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the
40、entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking
41、 for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535,
42、appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from
43、a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device
44、 classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535,
45、 appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any cha
46、nge that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shal
47、l be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 38 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permit
48、ted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87694 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 6 DSCC FORM 2234 APR 97 TABLE IA. Electrical performance characteristics. Test and MIL-STD-883 method 1/ Symbol Test conditions 2/ 3/ -55C TC +125C +3.0 V VCC +5.5 V unless otherwise specified Device type and device class VCCGroup A subgroups Limits 4/ Unit Min Max Positive input clamp voltage 3022 VIC+For input under test, IIN= 1.0 mA All V 0.0 V 1 0.4 1.5 V Negative input clamp voltage 3022 VIC-For input under test, IIN=
