1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with N.O.R 5962-R319-92. 92-09-30 M. A. FRYE B Drawing updated to reflect current requirements. Add theta JC to 1.3. Make change to -ISCand +ISCtests as specified under table I. ro 00-08-28 R. MONNIN C Replaced reference to
2、MIL-STD-973 with reference to MIL-PRF-38535. -rrp 03-12-17 R. MONNIN D Update paragraphs to current MIL-PRF-38535 requirements. -rrp 10-11-16 C. SAFFLE THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 PMIC N
3、/A PREPARED BY MARCIA B. KELLEHER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY D. A. DiCENZO APPROVED BY N. A. HAUCK MICROCIRCUIT, LINEAR,
4、 DUAL MATCHED HIGH PERFORMANCE OPERATIONAL AMPLIFIERS, MONOLITHIC SILICON DRAWING APPROVAL DATE 87-09-15 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-87714 SHEET 1 OF 8 DSCC FORM 2233 APR 97 5962-E080-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr
5、om IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87714 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with M
6、IL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-87714 01 G A Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as f
7、ollows: Device type Generic number Circuit function 01 OP-14A Dual matched high performance operational amplifiers 02 OP-14B Dual matched high performance operational amplifiers 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive de
8、signator Terminals Package style G MACY1-X8 8 Can P GDIP1-T8 or CDIP2-T8 8 Dual-in-line 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage (VS) . 22 V Power dissipation (PD) 500 mW Differential input voltage 30 V Input voltag
9、e Supply voltage Output short-circuit duration Indefinite Storage temperature range . -65C to +150C Lead temperature range (soldering, 60 seconds) +300C Junction temperature (TJ) -65C to +150C Thermal resistance, junction-to-case (JC) See MIL-STD-1835 1.4 Recommended operating conditions. Supply vol
10、tage (VS) 15 V dc Ambient operating temperature range (TA) . -55C to +125C Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87714 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC F
11、ORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitat
12、ion or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DE
13、FENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelp
14、hia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obt
15、ained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and quali
16、fied manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Qualit
17、y Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to ide
18、ntify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal
19、connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electr
20、ical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 here
21、in. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall
22、 be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. Provided by IHSNot for ResaleNo reproduction or net
23、working permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87714 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C VS= 15 V unless otherwis
24、e specified Group A subgroups Device type Limits Unit Min Max Input offset voltage VOSRS 20 k 1 01 -0.75 0.75 mV 2, 3 -1.5 1.5 1 02 -5 5 2, 3 -6 6 Input offset current IOS1 01 -5 5 nA 2, 3 -10 10 1 02 -25 25 2, 3 -50 50 Input bias current IB1 01 -50 50 nA 2, 3 -60 60 1 02 -100 100 2, 3 -200 200 Inpu
25、t voltage range IVR 1/ 1, 2, 3 All 10 V Common mode rejection ratio CMRR VCM= IVR = 10 V, RS 20 k 1 01 85 dB 2, 3 80 1, 2, 3 02 70 Power supply rejection ratio PSRR VS= 5 V to 20 V, RS 20 k 1, 2, 3 01 60 V/V 02 150 Output voltage swing VORL 2 k 4, 5, 6 01 12 V 4 02 12 5, 6 10 Large signal voltage ga
26、in AVOVO= 10 V, RL 2 k 4 01 100 V/mV 5, 6 50 4 02 50 5, 6 25 Power supply current ISYNo load each amplifier, TA= +25C 1 All 3 mA Power dissipation PDNo load each amplifier, TA= +25C 1 All 90 mW Channel separation CS TA= +25C 7 01 100 dB 02 80 Output short circuit current -ISCTA= +25C 1 All -60 mA +I
27、SC60 Input resistance differential mode RINTA= +25C 2/ 1 01 2.0 M 02 1.0 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87714 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 RE
28、VISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA +125C VS= 15 V unless otherwise specified Group A subgroups Device type Limits Unit Min Max Rise time trAVCL= +1, VIN= 50 mV, RL 2 k, RS= 50 , CL= 50 pF, TA= +25C 9
29、All 350 ns Overshoot OS AVCL= +1, VIN= 50 mV, RL 2 k, RS= 50 , CL= 50 pF, TA= +25C 9 All 10 % Slew rate SR RL 2 k, RS= 50 k, CL= 100 pF, TA= +25C 7 All 0.25 V/s Bandwidth BW AVCL= +1, TA= +25C 3/ 7 All 1 MHz Large signal bandwidth LSBW VO= 20 VP-P, 4/ TA= +25C 7 All 4 kHz Input offset voltage match
30、VOS1 All -1 1 mV 2, 3 -1.5 1.5 Common mode rejection match CMRR VCM= 10 V, RS 100 1 All 94 dB 2, 3 90 1/ IVR is guaranteed by CMRR test. 2/ RINis guaranteed by IBtest. RIN= 4 kT/qIBwhere kT/q = 0.026 at +25C. 3/ Bandwidth is guaranteed by trtest. BW = 0.35/ tr. 4/ Large signal bandwidth is guarantee
31、d by SR test. LSBW = SR/(2 x x VPEAK). 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior t
32、o listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot
33、 of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be required for any change that affects this drawing. 3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritime s agent, and the acquiring activity retai
34、n the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWI
35、NG SIZE A 5962-87714 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 Device types 01 and 02 Case outlines G and P Terminal number Terminal symbol 1 OUT A 2 -IN A 3 +IN A 4 -VS5 +IN B 6 -IN B 7 OUT B 8 +VSFIGURE 1. Terminal connections. Provided by IHSNo
36、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87714 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedu
37、res shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MI
38、L-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipati
39、on, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the
40、 manufacturer. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II he
41、rein. b. Subgroups 8, 10, and 11 in table I, method 5005 of MIL-STD-883 shall be omitted. 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D.
42、 The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the in
43、tent specified in method 1005 of MIL-STD-883. (2) TA= +125C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87714 D
44、LA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Interim electrical parameters (method 5004) 1 Final electrical test par
45、ameters (method 5004) 1*,2,3,4,5,6 Group A test requirements (method 5005) 1,2,3,4,5,6,7,9 Groups C and D end-point electrical parameters (method 5005) 1 * PDA applies to subgroup 1. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, ap
46、pendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic devic
47、e covered by a contractor-prepared specification or drawing. 6.3 Configuration control of SMDs. All proposed changes to existing SMDs will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.4
48、 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires configuration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962) should contact DLA Land and Maritime -VA, telephone (614) 692-0547. 6.5 Commen
