1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device type 03. Remove vendor CAGE 64155 for device type 02. Remove vendor CAGE 06665. Make changes to table I, 1.2.2, figure 1, and editorial changes throughout. 93-03-17 M. A. FRYE B Table I. Long term input voltage stability test. Under gr
2、oup A subgroups column, delete 2 and 3 entirely. Average input offset voltage drift test. Under group A subgroup column, delete 1 entirely. Changes in accordance with NOR 5962-R219-94. 94-07-08 M. A. FRYE C Add vendor CAGE 24355 to device type 02, and class V for case outlines 2, and H. Update to cu
3、rrent boiler plate and editorial changes throughout. Redrawn. 97-05-30 R. MONNIN D Replaced reference to MIL-STD-973 with reference to MIL-PRF-38535. -rrp 03-07-16 R. MONNIN E Make correction to the Average input offset voltage drift max test limit in table I by deleting “10 V/C” and substituting “1
4、.0 V/C”. Update boilerplate paragraphs to current MIL-PRF-38535 requirements. - ro 11-01-20 C. SAFFLE THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHET REV SHET REV STATUS REV E E E E E E E E E E E E OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Charles E. Besore
5、 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY Raymond Monnin APPROVED BY D. A. DiCenzo MICROCIRCUIT, LINEAR, PRECISION, LOW OFFSET, OPERAT
6、IONAL AMPLIFIER, MONOLITHIC SILICON DRAWING APPROVAL DATE 88-07-26 AMSC N/A REVISION LEVEL E SIZE A CAGE CODE 67268 5962-87738 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E458-10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAW
7、ING SIZE A 5962-87738 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice
8、of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following examples. For device classes M and Q: 5962 - 87738
9、01 X A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Case outline (see 1.2.4)Lead finish (see 1.2.5) / /Drawing number For device class V: 5962 - 87738 01 V X A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designator
10、Case outline (see 1.2.4) Leadfinish (see 1.2.5) / (see 1.2.3) /Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appe
11、ndix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 LT1001, OP-77B Precision operational amplifier 02 O
12、P-77A Precision operational amplifier 03 LT1001A Precision operational amplifier 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as listed below. Since the device class designator has been added after the original issuance of this
13、 drawing, device classes M and Q designators will not be included in the PIN and will not be marked on the device. Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-
14、38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87738 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 3 DSCC FO
15、RM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style G MACY1-X8 8 Can H GDFP1-F10 or CDFP2-F10 10 Flat pack P GDIP1-T8 or CDIP2-T8 8 Dual-in-line 2 CQCC1-N20 20 Square leadless chip c
16、arrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. 1.3 Absolute maximum ratings. 1/ Supply voltage (VS) . 22.0 V dc Internal power dissipation . 500 mW Input voltage . 22.0 V dc 2/ Differential input
17、voltage 30 Vdc Output short-circuit duration Indefinite Lead temperature (soldering, 10 seconds) +300C Storage temperature range . -65C to +150C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA): Case G . +150C/W Case P +119C/W Case 2 +110C/W C
18、ase H . +150C/W Junction temperature (TJ) . +150C 1.4 Recommended operating conditions. Supply voltage range (VS) . 3 V dc to 18 V dc Ambient operating temperature range (TA) . -55C to +125C _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation
19、at the maximum levels may degrade performance and affect reliability. 2/ For supply voltage less than 22 V, the absolute maximum input voltage is equal to the supply voltage. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWI
20、NG SIZE A 5962-87738 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specifie
21、d herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard M
22、icrocircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quic
23、ksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this do
24、cument, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device
25、 manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified h
26、erein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in acco
27、rdance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation paramet
28、er limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The p
29、art shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product us
30、ing this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q
31、and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-8773
32、8 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA+125C Group A subgroupsDevice type Limits 1/ Unit VS= 15 V unless otherwise specified Min Max Long term input offset voltage
33、 stability VOS/ time 2/ 3/ 1 01,02 1.5 V/Mo 03 1.0 Average input offset 3/ voltage drift VOS/ temp 2,3 01 -1.0 1.0 V/C 02,03 -0.6 0.6Input offset current IOS1 01 -3.8 3.8 nA 2,3 -7.6 7.61 02 -1.5 1.52,3 -2.2 2.2 1 03 -2.0 2.02,3 -4.0 4.0Input bias current IB1 01 -4.0 4.0 nA 2,3 -8.0 8.01 02,03 -2.0
34、2.02,3 -4.0 4.0 Input voltage range +VIN1,2,3 All +13.0 V -VIN-13.0Power dissipation PDNo load 1 01 80 mW 2,3 100No load, VS= 3 V 1 8 No load 1 02 602,3 75No load, VS= 3 V 1 4.5 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I
35、HS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87738 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA+125C Group A subgroupsDevice type Limits 1/ Unit VS= 15 V un
36、less otherwise specified Min Max Power dissipation PDNo load 1 03 75 mW 2,3 90No load, VS= 3 V 1 6.0 Input resistance 3/ differential mode RINTA= +25C 1 All 15 M Common mode rejection ratio CMRR VCM= 13 V 1 01 110 dB 2,3 106 1,2,3 02 1201 03 1142,3 110 Power supply rejection ratio PSRR VS= 3 V to 18
37、 V 1 01,02 106 dB 2,3 1001 03 1102,3 104 Input offset voltage 4/ VOS4 01 -60 60 V 2,3 -160 1604 02 -25 25 2,3 -60 604 03 -15 152,3 -60 60 Large signal voltage gain AVOLRL 2 k, VO= 12 V 4 01 400 V/mV RL 1 k, VO= 10 V 250 RL 2 k, VO= 10 V 5,6 200 RL 2 k, VO= 10 V 4 02 5000 5,6 2000 See footnotes at en
38、d of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87738 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics
39、 Continued. Test Symbol Conditions -55C TA+125C Group A subgroupsDevice type Limits 1/ Unit VS= 15 V unless otherwise specified Min Max Large signal voltage gain AVOLRL 2 k, VO= 12 V 4 03 450 V/mV RL 1 k, VO= 10 V 300 RL 2 k, VO= 10 V 5,6 300 Output voltage swing +VOUTRL 1 k 4 All +12.0 V RL 2 k 4 +
40、12.5 5,6 +12.0-VOUTRL 1 k 4 -12.0 RL 2 k 4 -12.5 5,6 -12.0Slew rate 3/ SR RL 2 k, TA= +25C 7 All 0.1 V/s Input noise voltage 3/ 5/ enpp0.1 Hz to 10 Hz, TA= +25C 7 All 0.6 VPPInput noise voltage density 5/ en fO= 10 Hz, TA= +25C 7 All 18.0 nV / fO= 1000 Hz, TA= +25C 11.0 Hz Input noise current 3/ 5/
41、in fO= 10 Hz, TA= +25C 7 All .80 pA / fO= 1000 Hz, TA= +25C .17 Hz Gain bandwidth product 3/ GBW TA= +25C 7 All 0.4 MHz 1/ The algebraic convention, whereby the most negative value is a minimum and the most positive is a maximum, is used in this table. Negative current shall be defined as convention
42、al current flow out of device terminal. 2/ Long term input offset voltage stability refers to the average trend line of offset voltage versus time over extended periods after the first 30 days of operation. Excluding the first hour of operation, changes in VOSduring the first 30 days are normally 2.
43、5 V. 3/ If not tested, shall be guaranteed to the limits specified in table I herein. 4/ For device types 01 and 02, inputs offset voltage is measured with high speed test equipment approximately 1 second after power is applied. For device type 03, input offset voltage is measured after power is app
44、lied and the device is fully warmed up. 5/ 10 Hz noise voltage density is sample tested on every lot. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87738 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVI
45、SION LEVEL E SHEET 8 DSCC FORM 2234 APR 97 Device types 01,02,03 02 01, 02 Case outlines G and P H 2 Terminal number Terminal symbol 1 VOSTRIM NC NC 2 -INPUT VOSTRIM VOSTRIM 3 +INPUT -INPUT NC4 -VS+INPUT NC 5 NC-VS-INPUT 6 OUTPUT NC NC 7 +VSOUTPUT +INPUT 8 VOSTRIM +VSNC 9 - VOSTRIM NC 10 - NC -VS11
46、- - NC 12 - - NC 13 - - NC 14 - - NC 15 - - OUTPUT 16 - - NC 17 - - +VS18 - - NC 19 - - NC 20 - - VOSTRIM NC = No connection FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-877
47、38 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 9 DSCC FORM 2234 APR 97 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see
48、6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the m
