DLA SMD-5962-87741 REV J-2010 MICROCIRCUIT LINEAR NEGATIVE ADJUSTABLE REGULATOR MONOLITHIC SILICON.pdf

资源描述

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add vendor CAGE 69210. Add case outline U. Editorial changes throughout. 91-05-07 M. A. FRYE B Changes in accordance with NOR 5962-R088-93. 93-03-15 M. A. FRYE C Changes in accordance with NOR 5962-R206-94. 94-06-14 M. A. FRYE D Changes in accord

2、ance with NOR 5962-R216-96. 96-09-12 R. MONNIN E Add radiation hardness requirements. Redrawn. rrp 00-04-19 R. MONNIN F Add case outline Y. - ro 02-04-30 R. MONNIN G Drawing updated to reflect current requirements. - rrp 05-07-19 R. MONNIN H Make correction to Load regulation test unit column as spe

3、cified under Table I. Make a change to IOUTunder footnote 3/ as specified under Table I. - ro 05-08-10 R. MONNIN J Update drawing as part of the 5 year review. - jt 10-11-17 C. SAFFLE THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV J J J J J J J J J J J

4、 J OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY MARCIA B. KELLEHER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY CHARLES

5、 REUSING APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, NEGATIVE ADJUSTABLE REGULATOR MONOLITHIC SILICON DRAWING APPROVAL DATE 88-01-08 AMSC N/A REVISION LEVEL J SIZE A CAGE CODE 67268 5962-87741 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E084-11 Provided by IHSNot for ResaleNo reproduction or netw

6、orking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87741 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL J SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B

7、 microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-87741 01 X A Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device type. The device type ident

8、ify the circuit function as follows: Device type Generic number Circuit function 01 1033 3.0 A negative regulator, adjustable 1.2.2 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style T See figure 1 3 TO-257

9、 flange mounted with non-isolated tab and glass sealed U See figure 1 3 TO-257 flange mounted with isolated tab and glass sealed X MBFM1-P2 2 TO-3 can Y See figure 1 3 Flange mount, glass sealed with gull wing leads 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3

10、 Absolute maximum ratings. Input to output voltage differential . 35 V dc Power dissipation (PD) . Internally limited Lead temperature (soldering, 10 seconds) . +300C Junction temperature (TJ) . +150C Storage temperature range . -65C to +150C Thermal resistance, junction-to-case (JC): Case T 2.3C/W

11、Cases U and Y 3.5C/W Case X 3.0C/W 1.4 Recommended operating conditions. Ambient operating temperature range (TA) -55C to +125C 1.5 Radiation features: Maximum total dose available (dose rate = 50 300 rads(Si) / s) . 30 Krads (Si) 1/ _ 1/ These parts may be dose rate sensitive in a space environment

12、 and may demonstrate enhanced low dose rate effects. Radiation end point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883, method 1019, condition A. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STA

13、NDARD MICROCIRCUIT DRAWING SIZE A 5962-87741 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL J SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawin

14、g to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883

15、- Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/

16、assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes preced

17、ence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as sp

18、ecified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approv

19、ed program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall n

20、ot affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38

21、535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Radiation exposure circuit. The radiation exposure circuit shall be as specified on

22、figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall

23、be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For

24、packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PR

25、F-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCI

26、RCUIT DRAWING SIZE A 5962-87741 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL J SHEET 4 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ 2/ 3/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max R

30、nd of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87741 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL J SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristic

31、s - Continued. Test Symbol Conditions 1/ 2/ 3/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Ripple rejection 6/ VIN/ VOUT= -10 V, f = 120 Hz, 4 01 56 dB VREFCADJ= 0 M,D,P 4 56 VOUT= -10 V, f = 120 Hz, CADJ= 0 5, 6 53 VOUT= -10 V, f = 120 Hz, 4 70 CADJ= 1

32、0 F M,D,P 4 70 VOUT= -10 V, f = 120 Hz, CADJ= 10 F 5, 6 60 Adjust pin current IADJVDIFF= 35 V, IL= 10 mA 1,2,3 01 100 A M,D,P 1 100 Adjust pin current change IADJ10 mA IOUT 3 A 1,2,3 01 2.0 A M,D,P 1 2.0 3.0 V |VIN VOUT| 35 V 1,2,3 5.0 M,D,P 1 5.0 Minimum load current IMIN|VIN VOUT| 35 V 1,2,3 01 5.

34、e from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87741 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL J SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ 2/ 3/ -55C TA +125C unless otherwise specified Group A

35、subgroups Device type Limits Unit Min Max Current limit 4/ ICL|VIN VOUT| = 30 V 1,2,3 01 0.7 A M,D,P 1 0.7 |VIN VOUT| = 35 V 1 0.5 2.5 M,D,P 1 0.5 2.5 |VIN VOUT| = 35 V 2,3 0.5 Temperature 6/ stability VOUT / T -55C TJ +125C 1,2,3 01 1.5 % M,D,P 1 1.5 Long term stability 6/ VOUT/ t TA= +125C, t = 10

36、00 hours 2 01 1.0 % 1/ Devices supplied to this drawing will meet all levels M, D, P of irradiation. However, this device is only tested at the P level. Pre and Post irradiation values are identical unless otherwise specified in table I. When performing post irradiation electrical measurements for a

37、ny RHA level, TA= +25C. 2/ These parts may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects. Radiation end point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883, method 1019, condition A. 3/ Unless oth

38、erwise specified, these specifications apply for |VIN VOUT| = 5.0 V and IOUT= 5 mA. 4/ Current limit is folded back for input to output voltage above 10 V. 30 W power dissipation is guaranteed only for 10 V VIN VOUT 20 V. Below 10 V, the 3 A current limit applies, and above 20 V, guaranteed current

39、limit will reduce maximum guaranteed power to less than 30 W. 5/ Regulation is measured on the output at a point 1/8 inch below the base of the package using a pulsed low duty cycle technique. 6/ Guaranteed, if not tested, to the limits specified in table I herein. Provided by IHSNot for ResaleNo re

40、production or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87741 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL J SHEET 7 DSCC FORM 2234 APR 97 Case outlines T and U Letter Inches Millimeters Min Max Min Max A .190 .200 4.83 5.08 A1 .035

41、 .045 0.89 1.14 A2 .120 BSC 3.05 BSC b .025 .035 0.64 0.89 D .645 .665 16.38 16.89 D1 .410 .430 10.41 10.92 D3 .000 .065 0.00 1.65 e .100 BSC 2.54 BSC E .410 .422 10.41 10.72 L .500 .750 12.70 19.05 O .527 .537 13.39 16.64 P .140 .150 3.56 3.81 NOTE: The U.S. government preferred system of measureme

42、nt is the metric SI system. However, since this item was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or ne

43、tworking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87741 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL J SHEET 8 DSCC FORM 2234 APR 97 Case outline Y Symbol Inches Millimeters Min Max Min Max A .190 .210 4.83 5.33 b - .030 - 0.76 D .410 .430 10

44、.41 10.92 D1 .580 .610 14.73 15.49 e - .100 - 2.54 e1 - .200 - 5.08 E .410 .420 10.41 10.67 L1 .090 .110 2.29 2.79 L .115 .125 2.92 3.18 N 3 3 NOTE: The U.S. government preferred system of measurement is the metric SI system. However, since this item was originally designed using inch-pound units of

45、 measurement, in the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. FIGURE 1. Case outline Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87

46、741 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL J SHEET 9 DSCC FORM 2234 APR 97 Device type 01 Case outlines X U T Y Terminal number Terminal symbol 1 ADJUST ADJUST ADJUST ADJUST 2 VOUTVINVINVIN3 VIN(CASE) VOUTVOUTVOUT4 - NC VIN- NC = No connection FIGURE 2. Terminal connections.

47、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87741 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL J SHEET 10 DSCC FORM 2234 APR 97 Case U FIGURE 3. Radiation exposure circuit. Provided by I

48、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87741 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL J SHEET 11 DSCC FORM 2234 APR 97 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in o

展开阅读全文