1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Reference bias supply voltage, VBB1, condition column, delete “IOH= -0.4 mA“. Table I, footnote 1/, delete in its entirety and replace as follows: “Output load shall be 100 to -2.0 V for static parameters and 100 to 0.0 V for ECL AC parameters“.
2、Figure 3, modify to new logic diagram. Table IIA, for class M, final electrical, delete subgroups 10 and 11. 92-11-02 Monica L. Poelking B Changes in accordance with NOR 5962-R117-93. 93-03-26 Monica L. Poelking C Update to current requirements. Editorial changes throughout. - gap 06-05-18 Raymond M
3、onnin The original first page of this drawing has been replaced. REV SHET REV C C C C C SHEET 15 16 17 18 19 REV STATUS REV C C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Phu H. Nguyen DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHE
4、CKED BY Tim H. Noh COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Monica L. Poelking MICROCIRCUIT, DIGITAL, ECL, TWO-MODULUS PRESCALER, DIVIDE BY 10 AND 11, AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 92-07-13 MON
5、OLITHIC SILICON AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-87749 SHEET 1 OF 19 DSCC FORM 2233 APR 97 5962-E339-06 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87749 DEFENSE SUPPLY CENTER COLUMBU
6、S COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are ava
7、ilable and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 87749 01 M E X Federal stock class designator RHA designator (see 1.2.1) Dev
8、ice type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RH
9、A marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 12513
10、Two-modulus prescaler, an ECL to TTL translator, with divide by 10 and 11. 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements
11、for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Termi
12、nals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-
13、,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87749 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage range (VCC) (VEE= 0) 0 V dc to +7.0 V dc Supply voltage range (VEE) (VCC= 0) . -8.0 V dc to 0 V dc
14、 Output voltage (VOUT) +5.5 V dc Input voltage (VIN) +5.5 V dc Maximum power dissipation 460 mW Storage temperature range (TS) -65C to 175C Lead temperature (soldering,10 seconds) +300C Junction temperature (TJ) . +165C Thermal resistance, junction-to-case (JC) See MIL-STD-1835 1.4 Recommended opera
15、ting conditions. Supply voltage (VCC) (VEE= 0) . 4.5 V dc minimum to 5.5 V dc maximum Supply voltage (VEE) (VCC= 0) . -5.46 V dc minimum to -4.94 V dc maximum Case operating temperature range (TC) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The follo
16、wing specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing,
17、General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircu
18、it Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or www.dodssp.daps.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between th
19、e text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage t
20、o the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87749 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218
21、-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modif
22、ication in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensio
23、ns. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connectio
24、ns. The terminal connections shall be as specified on figure 1. 3.2.3 Truth and state diagram. The truth and state diagram shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Test circuit and switching waveforms. The test circuit and swi
25、tching waveforms shall be as specified on figure 4. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the
26、 full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition
27、, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking
28、 for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The co
29、mpliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 he
30、rein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing
31、shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q a
32、nd V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acqu
33、ired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore document
34、ation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 33 (see MIL-PRF-38535, appendix A).Provided by IHSNot for ResaleNo reproduction or networki
35、ng permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87749 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits Test Symbol Conditions 1/ -55C TC +125C VCC= 5.0 V
36、 10% unless otherwise specified Group A sub- groups Min Max Unit E5 MTTL 0.5 V 2.4 V 0.5 V 0.5 V 0.5 V 0.5 V E4 MTTL 0.5 V 0.5 V 2.4 V 0.5 V 0.5 V 0.5 V E3 MECL 3.11 V 3.11 V 3.11 V 4.22 V 3.11 V 3.11 V E2 MECL 3.11V 3.11 V 3.11 V 3.11 V 4.22 V 3.11 V E1 MECL 3.11 V 3.11 V 3.11 V 3.11 V 3.11 V 4.22
37、V 1 4.03 4.22 E5 MTTL 0.5 V 2.4 V 0.5 V 0.5 V 0.5 V 0.5 V E4 MTTL 0.5 V 0.5 V 2.4 V 0.5 V 0.5 V 0.5 V E3 MECL 3.14 V 3.14 V 3.14 V 4.37 V 3.14 V 3.14 V E2 MECL 3.14V 3.14 V 3.14 V 3.14 V 4.37 V 3.14 V E1 MECL 3.14 V 3.14 V 3.14 V 3.14 V 3.14 V 4.37 V 2 4.135 4.37 Output voltage high (prescaler) VOH1
38、2/ VEE= 0.0 V VCC = 5.0 V VCCO= 5.0 V See figure 2. E5 MTTL 0.5 V 2.4 V 0.5 V 0.5 V 0.5 V 0.5 V E4 MTTL 0.5 V 0.5 V 2.4 V 0.5 V 0.5 V 0.5 V E3 MECL 3.04 V 3.04 V 3.04 V 4.12 V 3.04 V 3.04 V E2 MECL 3.04V 3.04 V 3.04 V 3.04 V 4.12 V 3.04 V E1 MECL 3.04 V 3.04 V 3.04 V 3.04 V 3.04 V 4.12 V 3 3.88 4.12
39、 V E5 MTTL 0.5 V 2.4 V 0.5 V 0.5 V 0.5 V 0.5 V E4 MTTL 0.5 V 0.5 V 2.4 V 0.5 V 0.5 V 0.5 V E3 MECL 3.11 V 3.11 V 3.11 V 4.22 V 3.11 V 3.11 V E2 MECL 3.11V 3.11 V 3.11 V 3.11 V 4.22 V 3.11 V E1 MECL 3.11 V 3.11 V 3.11 V 3.11 V 3.11 V 4.22 V 1 3.11 3.44 E5 MTTL 0.5 V 2.4 V 0.5 V 0.5 V 0.5 V 0.5 V E4 M
40、TTL 0.5 V 0.5 V 2.4 V 0.5 V 0.5 V 0.5 V E3 MECL 3.14 V 3.14 V 3.14 V 4.37 V 3.14 V 3.14 V E2 MECL 3.14V 3.14 V 3.14 V 3.14 V 4.37 V 3.14 V E1 MECL 3.14 V 3.14 V 3.14 V 3.14 V 3.14 V 4.37 V 2 3.14 3.515 Output voltage low (prescaler) VOL1E5 MTTL 0.5 V 2.4 V 0.5 V 0.5 V 0.5 V 0.5 V E4 MTTL 0.5 V 0.5 V
41、 2.4 V 0.5 V 0.5 V 0.5 V E3 MECL 3.04 V 3.04 V 3.04 V 4.12 V 3.04 V 3.04 V E2 MECL 3.04V 3.04 V 3.04 V 3.04 V 4.12 V 3.04 V E1 MECL 3.04 V 3.04 V 3.04 V 3.04 V 3.04 V 4.12 V 3 3.04 3.405 V See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without lic
42、ense from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87749 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Conditions 1/ -55C TC +125C VCC= 5.0 V 10% unless
43、otherwise specified Group A sub- groups Min MaxUnitOutput voltage high (translator) VOH2VEE= 0.0 V VCC = 5.0 V MTTL Output = -0.4 mA VIHA(-) 3.895 V 4.000 V 3.745 V VIHB(-) 4.22 V 4.37 V 4.12 V VILA(+) 3.525 V 3.600 V 3.500 V VILB(+) 3.11 V 3.14 V 3.04 V 1 2 3 2.70 3.00 2.40 4.50 4.50 4.50 Output vo
44、ltage low (translator) VOL2VEE= 0.0 V VCC= 5.0 V MTTL Output = 16 mA VIHA(-) 3.895 V 4.000 V 3.745 V VIHB(-) 4.22 V 4.37 V 4.12 V VILA(+) 3.525 V 3.600 V 3.500 V VILB(+) 3.11 V 3.14 V 3.04 V 1 2 3 0.10 0.10 0.10 0.80 0.66 1.00 V E5 MTTL 0.8 V 0.5 V 0.5 V 0.5 V 0.5 V 2.0 V 0.5 V 0.5 V 0.5 V 0.5 V E4
45、MTTL 0.5 V 0.8 V 0.5 V 0.5 V 0.5 V 0.5 V 2.0 V 0.5 V 0.5 V 0.5 V E3 MECL 3.11 V 3.11 V 3.525 V 3.11 V 3.11 V 3.11 V 3.11 V 3.895 V 3.11 V 3.11 V E2 MECL 3.11 V 3.11 V 3.11 V 3.525 V 3.11 V 3.11 V 3.11 V 3.11 V 3.895 V 3.11 V E1 MECL 3.11 V 3.11 V .3.11 V 3.11 V 3.525 V 3.11 V 3.11 V 3.11 V 3.11 V 3.
46、895 V 1 4.01 4.22E5 MTTL 0.8 V 0.5 V 0.5 V 0.5 V 0.5 V 2.0 V 0.5 V 0.5 V 0.5 V 0.5 V E4 MTTL 0.5 V 0.8 V 0.5 V 0.5 V 0.5 V 0.5 V 2.0 V 0.5 V 0.5 V 0.5 V E3 MECL 3.14 V 3.14 V 3.60 V 3.14 V 3.14 V 3.14 V 3.14 V 4.00 V 3.14 V 3.14 V E2 MECL 3.14 V 3.14 V 3.14 V 3.60 V 3.14 V 3.14 V 3.14 V 3.14 V 4.00
47、V 3.14 V E1 MECL 3.14 V 3.14 V 3.14 V 3.14 V 3.60 V 3.14 V 3.14 V 3.14 V 3.14 V 4.00 V 2 4.115 4.37 Output voltage high (prescaler) VOHAVEE= 0.0 V VCC = 5.0 V VCCO = 5.0 V See figure 2 E5 MTTL 0.8 V 0.5 V 0.5 V 0.5 V 0.5 V 2.0 V 0.5 V 0.5 V 0.5 V 0.5 V E4 MTTL 0.5 V 0.8 V 0.5 V 0.5 V 0.5 V 0.5 V 2.0
48、 V 0.5 V 0.5 V 0.5 V E3 MECL 3.04 V 3.04 V 3.50 V 3.04 V 3.04 V 3.04 V 3.04 V 3.745 V 3.04 V 3.04 V E2 MECL 3.04 V 3.04 V 3.04 V 3.50 V 3.04 V 3.04 V 3.04 V 3.04 V 3.745 V 3.04 V E1 MECL 3.04 V 3.04 V 3.04 V 3.04 V 3.50 V 3.04 V 3.04 V 3.04 V 3.04 V 3.745 V 3 3.86 4.12V See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87749 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance char