1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with N.O.R. 5962-R220-93. 93-08-26 M. A. FRYE B Changes in accordance with N.O.R. 5962-R153-94. 94-04-29 M. A. FRYE C Drawing updated to reflect current requirements. - ro 00-06-02 R. MONNIN D Replaced reference to MIL-STD-9
2、73 with reference to MIL-PRF-38535. Drawing updated to reflect current requirements. - gt 04-06-09 R. MONNIN E Update drawing as part of 5 year review. - jt 11-01-18 C. SAFFLE THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV E E E E E E E E E E E OF SHEE
3、TS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY RICK C. OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY CHARLES E. BESORE APPRO
4、VED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, OPERATIONAL AMPLIFIER, WIDEBAND, FAST SETTLING, MONOLITHIC SILICON DRAWING APPROVAL DATE 92-03-13 AMSC N/A REVISION LEVEL E SIZE A CAGE CODE 67268 5962-87784 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E146-11 Provided by IHSNot for ResaleNo reproduction or
5、networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87784 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class lev
6、el B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-87784 01 C X Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device types. The device types
7、 identify the circuit function as follows: Device type Generic number Circuit function 01 HA-5190 Fast settling wideband operational amplifier 02 EL-2190 Fast settling wideband operational amplifier 1.2.2 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline lett
8、er Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line X See figure 1 12 Can 2 CQCC1-N20 20 Square leadless chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Voltage between +V and V termina
9、ls 35 V dc Differential input voltage . 6.0 V dc Voltage at either input terminal . +V to V Peak output current ( 10 % duty cycle) 50 mA Storage temperature range . -65C to +150C Maximum power dissipation (PD) 1/: Case C 1.02 W Case X 1.45 W Case 2 . 1.06 W Lead temperature (soldering, 10 seconds) .
10、 +275C Junction temperature (TJ) . +175C Thermal resistance, junction-to-case (JC): Cases C and 2 See MIL-STD-1835 Case X 82C/W Thermal resistance, junction-to-ambient (JA): Case C 98C/W Case X 69C/W Case 2 . 95C/W _ 1/ Derate linearly above TA= +75C as follows: case C at 10.2C/W, case X at 14.5C/W,
11、 and case 2 at 10.6C/W. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87784 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 3 DSCC FORM 2234 APR 97 1.4 Recommended operating condition
12、s. Positive supply voltage range (+V) +12 V dc to +15 V dc Negative supply voltage range (-V) . -12 V dc to 15 V dc Common mode input voltage (VCM) . |(+V (-V) / 2| Load resistance (RL) . 200 Ambient operating temperature (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, sta
13、ndards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Inte
14、grated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MI
15、L-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict
16、between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item require
17、ments shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional cer
18、tification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein.
19、 These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and phy
20、sical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified
21、on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements sha
22、ll be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87784 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-399
23、0 REVISION LEVEL E SHEET 4 DSCC FORM 2234 APR 97 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is n
24、ot feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall
25、be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (se
26、e 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certific
27、ate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be required for any change that affects this drawing. 3.9 Verification and rev
28、iew. DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 4. VERIFICATION 4.1 Sampling and in
29、spection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall
30、apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inp
31、uts, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn
32、-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87784 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 5 DSCC FORM 2234 APR 97 TAB
33、LE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min Max Input offset voltage VIOVCM= 0 V, 1 01 5 mV +RS= 100 , -RS= 100 2,3 10 1 02 2 2,3 6 Input bias current +IIBVCM= 0 V, +RS= 1.1 k, 1 All
34、 15 A -RS= 100 2,3 20 -IIBVCM= 0 V, +RS= 100 , 1 15 -RS= 1.1 k 2,3 20 Input offset current IIOVCM= 0 V, +RS= 1.1 k, 1 All 4.0 A -RS= 1.1 k 2,3 6.0 Common mode input voltage range +VCM+V = 10 V, -V = -20 V 1,2,3 All 5.0 V -VCM+V = 20 V, -V = -10 V -5.0 Large signal voltage gain +AVOLVOUT= 0 V and 5.0
35、 V, 1 All 15 kV/V RL= 200 2,3 5.0 -AVOLVOUT= 0 V and 5.0 V, 1 15 RL= 200 2,3 5.0 Common mode rejection ratio +CMRR VCM= 5.0 V, +V = 10 V, -V = -20 V, VOUT= -5.0 V 1,2,3 All 74 dB -CMRR VCM= -5.0 V, +V = 20 V, -V = -10 V, VOUT= 5.0 V 74 Output current +IOUTVOUT -5.0 V, TA= +25C 1 All 25 mA -IOUTVOUT
36、5.0 V, TA= +25C -25 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87784 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 6 DSCC FORM 2234 APR 97 TABLE I.
37、 Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min Max Output voltage swing +VOUTRL= 200 1,2,3 All 5.0 V -VOUT-5.0 Quiescent power supply current +ICCVOUT= 0 V, IOUT= 0 mA 1,2,3 01 25
38、mA 02 17 -ICC01 -25 02 -17 Power supply rejection ratio +PSRR +V = 10 V and 20 V, -V = -15 V 1,2,3 All 70 dB -PSRR -V = -10 V and 20 V, +V = +15 V 70 Slew rate +SR VOUT= -5.0 V to +5.0 V, 7 All 160 V/s RL= 200 , AV= +5 V/V 8 3/ 100 -SR VOUT= +5.0 V to 5.0 V, 7 160 RL= 200 , AV= +5 V/V 8 3/ 100 Gain
39、bandwidth 3/ 4/ product GBWP VOUT 200 mV, fO= 100 kHz, RL= 1 k, TA= +25C 4 All 150 MHz VOUT 200 mV, fO= 1.0 MHz, RL= 1 k, TA= +25C 150 Full power 3/ 5/ bandwidth FPBW VPK= 5.0 V, RL= 200 4 All 5.0 MHz 5,6 4.0 Closed loop stable 3/ gain CLSG RL= 200 , CL 10 pF 4,5,6 All 5.0 V/V Rise time 3/ 6/ trVOUT
40、= 0 V to +200 mV, 9 All 18 ns RL= 200 , AV= +5 V/V 10,11 20 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87784 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL
41、E SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min Max Fall time 3/ 6/ tfVOUT= 0 V to 200 mV, 9 All 18 ns RL= 200 , AV= +5 V/V 10,11 20 Overshoo
42、t 3/ +OS VOUT= 0 V to +200 mV, RL= 200 , AV= +5 V/V 9,10,11 All 40 % -OS VOUT= 0 V to 200 mV, RL= 200 , AV= +5 V/V 40 Output resistance 3/ ROUTOpen loop, TA= +25C, AV= +5 V/V 4 All 60 Quiescent power 7/ consumption PCVOUT= 0 V, IOUT= 0 mA 1,2,3 01 750 mW 02 510 Settling time 3/ ts5 V step to 0.01 %,
43、 RL= 200 9 All 200 ns 1/ +V = +15 V, -V = -15 V, RS= 100 , RL= 500 k, CL 10 pF, VOUT= 0 V, and AV= +5 V/V unless otherwise specified. 2/ The limiting term “min” (minimum) and “max” (maximum) shall be considered to apply to magnitudes only. Negative current shall be defined as conventional current fl
44、ow out of a device terminal. 3/ If not tested, shall be guaranteed to the limits specified in table I. 4/ Gain bandwidth product measured using open loop frequency response. 5/ Full power bandwidth = SR / ( 2 x x VPK). 6/ Rise and fall times measured between 10 % and 90 % point. 7/ Quiescent power c
45、onsumption based on quiescent supply current test maximum (no load on outputs). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87784 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 8 D
46、SCC FORM 2234 APR 97 Case X Letter Inches Millimeters Min Max Min Max A .130 .150 3.30 3.81 b .016 .021 0.41 0.53 D .585 .615 14.86 15.62 D1 .545 .555 13.84 14.10 e .400 BSC 10.16 BSC e1 .100 BSC 2.54 BSC F .020 .040 0.51 1.02 k .026 .034 0.67 0.86 k1 .026 .045 0.67 1.14 L .505 .562 12.83 14.27 NOTE
47、S: 1. The US government preferred system of measurement is the metric SI system. However, since this item was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. 2. Pin numbers are fo
48、r reference only and do not appear on package. 3. All leads increase maximum limit by .003 (0.08 mm) when lead finish A or B is applied. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87784 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 9 DSCC FORM 2234 APR 97 Device types 01 and 02 Case
