1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with N.O.R. 5962-R161-92. 92-05-22 M. A. FRYE B Make change to the overshoot test as specified in table I. - ro 01-11-01 R. MONNIN C Drawing updated to reflect current requirements. - ro 05-12-07 R. MONNIN D Update drawing p
2、aragraphs to current MIL-PRF-38535 requirements. -rrp 11-04-19 C. SAFFLE THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY CHARLES E. BESORE DLA LAND AND MARITIME COLUMBUS, OHIO
3、 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY D. H. JOHNSON APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, QUAD, LOW NOISE, OPERATIONAL AMPLIFIER, MONOLITHIC SILICON DRAWIN
4、G APPROVAL DATE 89-05-12 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-88502 SHEET 1 OF 10 DSCC FORM 2233 APR 97 5962-E314-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88502 DLA LAND AND MARITIM
5、E COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PI
6、N is as shown in the following example: 5962-88502 01 C A Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 HA-5104 Quad, low noise,
7、 operational amplifier 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line 2 CQCC1-N20 20 Square leadless chip carrier 1.2.3 Lead finish. The lead finish is
8、 as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Voltage between +VSand VSterminals 40 V dc Differential input voltage 7 V dc Input voltage (VIN) . +VSto VS1/ Output short circuit duration Indefinite 2/ Power dissipation (PD): Case C 1.29 W 3/ Case 2 . 1.32 W 3/ Storage temp
9、erature range . -65C to +150C Lead temperature (soldering, 10 seconds) 275C Junction temperature (TJ) . 175C Thermal resistance, junction-to-case (JC) See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA): Case C 78C/W Case 2 . 76C/W _ 1/ For supply voltages less than 15 V, the absolute maxi
10、mum input voltage is equal to the supply voltage. 2/ Any one amplifier may be shorted to ground indefinitely. 3/ Derate 12.9 mW/C above 75C for case C and 13.1 mW/C above 75C for case 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROC
11、IRCUIT DRAWING SIZE A 5962-88502 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.4 Recommended operating conditions. Positive supply voltage range (+VS) +5.0 V dc to +15 V dc Negative supply voltage range (-VS) . -5.0 V dc to -15 V dc Common mode inpu
12、t voltage (VCM) (+VS- -VS) / 2 Load resistance (RL) . 2 k Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified
13、 herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Mi
14、crocircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quick
15、search/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this doc
16、ument, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product b
17、uilt to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and quali
18、fying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as desc
19、ribed herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herei
20、n. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as
21、 specified in table I and shall apply over the full ambient operating temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88502 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D
22、SHEET 4 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Input offset voltage VIOVCM= 0 V 1 01 2.5 mV 2,3 3.0 Input offset current IIOVCM= 0 V, +RS= 10 k, 1 01 7
23、5 nA -RS= 10 k 2,3 125 Input bias current +IIBVCM= 0 V, +RS= 10 k, 1 01 200 nA -RS= 100 2,3 325 -IIBVCM= 0 V, +RS= 100 , 1 200 -RS= 10 k 2,3 325 Common mode voltage range +CMR +VS= 3 V, -VS= -27 V 1,2,3 01 +12 V -CMR +VS= 27 V, -VS= -3 V -12 Common mode rejection ratio +CMRR VCM= +5 V, +VS= +10 V, -
24、VS= -20 V, VOUT= -5 V 1,2,3 01 86 dB -CMRR VCM= -5 V, +VS= +20 V, -VS= -10 V, VOUT= +5 V 86 Output current +IOUTVOUT= -5 V 1,2,3 01 +10 mA -IOUTVOUT= +5 V -10 Quiescent power supply current +I VOUT= 0 V, IOUT= 0 mA 1 01 6.5 mA 2,3 7.5 -I 1 -6.5 2,3 -7.5 See footnotes at end of table. Provided by IHS
25、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88502 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Con
26、ditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Power supply rejection ratio +PSRR +VS= +10 V and +20 V, -VS= -15 V 1,2,3 01 86 dB -PSRR -VS= -10 V and -20 V, +VS= +15 V 86 Large signal voltage gain +AVOLVOUT= 0 V and +10 V, RL= 2 k 4,5,6 01 100
27、V/mV -AVOLVOUT= 0 V and -10 V, RL= 2 k 100 Output voltage swing +VOS1RL= 2 k 4,5,6 01 +10 V -VOS1-10 +VOS2RL= 10 k +12 -VOS2-12 Overshoot +OS VOUT= 0 V to +200 mV 2/ 9 01 35 % 10,11 3/ 35 -OS VOUT= 0 V to -200 mV 2/ 9 35 10,11 3/ 35 Slew rate +SR VOUT= -3 V to +3 V 2/ 7 01 1 V/s 8 3/ 0.7 -SR VOUT= +
28、3 V to -3 V 2/ 7 1 8 3/ 0.7 Rise time 4/ trVOUT= 0 V to 200 mV 2/ 9 01 200 ns 10,11 3/ 250 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88502 DLA LAND AND MARITIME COLUMBUS,
29、OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Fall time 4/ tfVOUT= 0 V to -200 mV 2/ 9 01 200 ns 10,11 3/ 2
30、50 Differential input 3/ resistance RINVCM= 0 V, TA= +25C 4 01 250 k Input noise voltage 3/ ENfO= 1.0 kHz, RS= 20 , TA= +25C 4 01 6.0 nV / Hz fO= 10 Hz, RS= 20 , TA= +25C 25.0 Input noise current 3/ INfO= 1.0 kHz, RS= 2 M, TA= +25C 4 01 3.0 pA / Hz fO= 10 Hz, RS= 2 M, TA= +25C 15.0 Unity gain 3/ ban
31、dwidth UGBW VOUT 200 mV, 2/ TA= +25C 4 01 4.8 MHz Full power 3/ 5/ bandwidth FPBW VPEAK= 10 V 2/ 4 01 15.9 kHz 5,6 11.0 Closed loop stable 3/ gain CLSG RL= 2.0 k, CL= 50 pF 4,5,6 01 1.0 V/V Output resistance 3/ ROUTTA= +25C 4 01 150 Quiescent power 6/ consumption PCVOUT= 0 V, IOUT= 0 mA 1,2,3 01 225
32、 mW Channel separation 3/ CS RS= 1 k, AVCL= 100 V/V, VIN= 100 mVp at 10 kHz referred to input, TA= +25C 4 01 55 dB 1/ Unless otherwise specified, +VS= +15 V, -VS= -15 V, RS= 100 , RL= 500 k, and VOUT= 0 V. 2/ AVCL= 1 V/V, RL= 2 k, CL= 50 pF, and RS= 50 . 3/ If not tested, shall be guaranteed to the
33、limits specified in table I herein. 4/ Rise and fall times measured between 10 and 90 percent points. 5/ Full power bandwidth = SR / ( 2 x VPEAK). 6/ Quiescent power consumption based in quiescent power supply current test maximum (no load on outputs). Provided by IHSNot for ResaleNo reproduction or
34、 networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88502 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 Device type 01 Case outlines C 2 Terminal number Terminal symbol 1 OUTPUT 1 NC 2 -INPUT 1 OUTPUT 1 3 +INPU
35、T 1 -INPUT 1 4 +VS+INPUT 1 5 +INPUT 2 NC 6 -INPUT 2 +VS7 OUTPUT 2 NC 8 OUTPUT 3 +INPUT 2 9 -INPUT 3 -INPUT 2 10 +INPUT 3 OUTPUT 2 11 -VSNC 12 +INPUT 4 OUTPUT 3 13 -INPUT 4 -INPUT 3 14 OUTPUT 4 +INPUT 3 15 - NC 16 - -VS17 - NC 18 - +INPUT 4 19 - -INPUT 4 20 - OUTPUT 4 NC = No connection FIGURE 1. Ter
36、minal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88502 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 APR 97 3.4 Electrical test requirements. The el
37、ectrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufactu
38、rers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devi
39、ces built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from
40、 a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-
41、38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DLA Land and Maritime
42、 -VA shall be required for any change that affects this drawing. 3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritime s agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be
43、 made available onshore at the option of the reviewer. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all
44、 devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available t
45、o the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall b
46、e as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88502 DLA LAND
47、 AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 9 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Interim electrical parameters (method 5004) - Final electrical test parameters
48、 (method 5004) 1*,2,3,4,5,6,7,9 Group A test requirements (method 5005) 1,2,3,4,5,6,7,8*,9,10*,11* Groups C and D end-point electrical parameters (method 5005) 1 * PDA applies to subgroup 1. * Subgroups 8, 10, and 11, if not tested, shall be guaranteed to the specified limits of table I. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with meth
