1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add vendor 50507 for device type 02XX. Change to reflect MIL-H-38534 processing. Editiorial changes throughout.91-10-22 G.A. Lude B Updated drawing to the latest requirements. -sld 05-04-25 Raymond Monnin C Added footnote 1 to table II, under gro
2、up C end-point electricals. Updated drawing paragraphs. -sld 09-07-28 Charles F. Saffle D Table I; added the Bipolar input (coding) test across -10V to +10 V range. Added 2/ to the Unipolar input (coding) 0 to +5V range and the Bipolar input (coding) -2.5 V to +2.5 V range tests. Changed the test co
3、ndition for the Bipolar input (coding) from -5V to +5.5 V to -5 V to +5 V range. Renamed the “Bipolar offset error“ test to “Bipolar zero error“ and “Bipolar offset gain error“ to “Bipolar zero drift “. -sld 10-01-19 Charles F. Saffle E Table I; Removed the differential nonlinearity drift test. Adde
4、d footnote 2 to the serial to parallel match test. Updated drawing paragraphs. -sld 11-08-19 Charles F. Saffle THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED REV SHEET REV SHEET REV STATUS OF SHEETS REV E E E E E E E E E E E E E E SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED
5、BY Gary Zahn DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING CHECKED BY Michael C. Jones THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Gregory Lude MICROCIRCUIT, HYBRID, LINEAR, 12-BIT ANALOG TO DIGITAL CONVERTER AND
6、AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 89-07-12 AMSC N/A REVISION LEVEL E SIZE A CAGE CODE 67268 5962-88508 SHEET 1 OF 14 DSCC FORM 2233 APR 97 5962-E462-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DR
7、AWING SIZE A 5962-88508 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for class H hybrid microcircuits to be processed in accordance with MIL-PRF-38534. 1.2 PIN. The PIN shall be as shown
8、in the following example: 5962-88508 01 X X Drawing number Device type Case outline Lead finish (see 1.2.1) (see 1.2.2) (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function Conversion time 01 ADC-HX 12-bit A/D conv
9、erter 20 s 02 ADC-HZ, MNADC87 12-bit A/D converter 8 s 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 32 Dual-in-line 1.2.3 Lead finish. The lead finish shall be as specified in
10、 MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Positive supply voltage range (VCC) . -0.3 V to +18 V dc Negative supply voltage range (VEE) +0.3 V to -18 V dc Logic supply voltage range (VDD) . -0.3 V to +7 V dc Analog input voltage -25 V Buffer input voltage VSDigital inputs +5.5 V Junction tempe
11、rature (TJ) +175C Storage temperature -65C to +150C Power dissipation (PD), TC = +25C 2 W Lead temperature (soldering, 10 seconds) +300C Thermal resistance: Junction-to-case (JC) . 13C/W Junction-to-ambient (JA) 41C/W 1.4 Recommended operating conditions. Positive supply voltage range (VCC) . +14.5
12、to +15.5 V dc Negative supply voltage range (VEE) -14.5 to -15.5 V dc Logic supply voltage range (VDD) . +4.5 V to +5.5 V dc Ambient operating temperature range (TA) -55C to +125C 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maxim
13、um levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88508 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 3 DSCC FORM 2234 APR 97 2
14、. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract.
15、DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 -
16、 List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order
17、 of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Ite
18、m requirements. The individual item requirements shall be in accordance with MIL-PRF-38534. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in a
19、ccordance with 1.2.2 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Functional diagram and input connection table. The functional diagram and input connection table shall be as specified on figure 3. 3.2.4 Truth table(s). The truth
20、table(s) shall be as specified on figure 4. 3.2.5 Timing diagram. The timing diagram shall be as specified on figure 5. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full
21、specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38
22、534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88508 DLA LAND AND MARI
23、TIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 4 DSCC FORM 2234 APR 97 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformanc
24、e inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available t
25、o the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm th
26、at the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspecti
27、on. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. Provided by IHSNot for ResaleNo reproduction or n
28、etworking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88508 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA+125C unless otherwise spe
29、cified Group A subgroups Device types Limits Unit Min Max Resolution RES Digital and serial 1,2,3 All 12 BIT Unipolar coding UC Complementary binary, (see 4.3.1b) 7,8 All Bipolar coding BC Complementary offset binary, (see 4.3.1b) 7,8 All Unipolar input (coding) 0 to +10 V range, TA= +25C, See figur
30、e 3 for input connections, (see 4.3.1b) 7 All Unipolar input (coding) 0 to +5 V range, TA= +25C, See figure 3 for input connections, (see 4.3.1b) 2/ 7 All Bipolar input (coding) -2.5 V to +2.5 V range, TA= +25C, See figure 3 for input connections, (see 4.3.1b) 2/ 7 All Bipolar input (coding) -5 V to
31、 +5 V range, TA= +25C, See figure 3 for input connections, (see 4.3.1b) 7 All Bipolar input (coding) -10 V to +10 V range, TA= +25C, See figure 3 for input connections, (see 4.3.1b) 7 All Buffer bias I BIAS TA= +25C 2/ 1 All 250 nA Buffer offset error BUFOE 1,2,3 All 10 mV Nonlinearity NL End-point
32、method 4 All 0.5 LSB 5,6 1 Differential nonlinearity DNL 4 All -0.75 +0.75 LSB 5,6 -1 +1 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88508 DLA LAND AND MARITIME COLUMBUS, OH
33、IO 43218-3990 REVISION LEVEL E SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TA+125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Unipolar gain error UGE 0 to 10 V range 4 All 0.2 %FSR 5,6 0.4
34、 Unipolar gain error drift UGE /T 0 V to 10 V range, TA= -55C, +125C 8 All 20 ppmFSR /C Bipolar gain error BGE -10 V to +10 V range 4 All 0.2 %FSR 5,6 All 0.4 Bipolar gain error drift BGE /T TA= -55C, +125C, -10 V to +10 V range, see figure 3 for input connections 8 All 20 ppmFSR /C Unipolar offset
35、error UOE 0 to +10 V range, see figure 3 for input connections 4 All 0.1 %FSR 5,6 0.2 Unipolar offset error drift UOE /T TA= -55C, +125C, 0 to +10 V range, see figure 3 for input connections 8 All 5 ppm/C Bipolar zero error BZE -10 V to +10 V range, see figure 3 for input connections 1 All 0.2 %FSR
36、2,3 0.4 Bipolar zero drift BZE /T TA= -55C, +125C, -10 V to +10 V range, see figure 3 for input connections 8 All 10 ppm/C No missing codes NMC Abbreviated test 4,5,6 All pass BIT See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from
37、 IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88508 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TA+125C unless otherwise specified Group A subgroups Dev
38、ice type Limits Unit Min Max Conversion time tCSee figure 5 9,10,11 01 20 s 02 8 Internal reference error VREFFrom 6.300 V, TA= +25C 1 All -126 +126 mV Internal reference error drift VREF/T TA= -55C, +125C 8 All 20 ppm/C Serial/parallel match 2/ MTCH Random codes, TA= +25C 7 All pass Digital output
39、voltage (high) VOH2 TTL loads 1,2,3 All 2.4 V Digital output voltage (low) VOL2 TTL loads 1,2,3 All 0.4 V Power supply rejection ratio (low) PSRR VS= 5% 1,2,3 All 0.004 %/%VSPositive supply current ICCVCC= +15.5 V 1,2,3 All 35 mA Negative supply current IEEVEE= -15.5 V 1,2,3 All -40 mA Logic supply
40、current IDDVDD= +5.5 V 1,2,3 All 124 mA Power dissipation PDNominal supply voltages 1,2,3 All 1.69 W 1/ Unless otherwise specified the following conditions apply: VCC= +15 V dc VEE= -15 V dc VDD= +5 V dc Logic “0“ = +0.8 V dc Logic “1“ = +2.0 V dc VFSR = 20 V Bipolar operation 2/ Parameter shall be
41、tested as part of device initial characterization and after design and process changes. Parameter shall be guaranteed to the limits specified in table I for all lots not specifically tested. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MI
42、CROCIRCUIT DRAWING SIZE A 5962-88508 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 8 DSCC FORM 2234 APR 97 Symbol Inches Millimeters Min Max Min Max A 1.720 43.69 B .880 1.100 22.35 27.94 C .235 5.97 D .016 .021 0.41 0.53 F .040 TYP 1.02 TYP G .100 BASIC 2.54 BASIC H .090 .1
43、10 2.29 2.79 J .009 .015 0.23 0.38 K .150 .211 3.81 5.36 L .890 .920 22.61 23.37 N .015 .060 0.38 1.52 NOTES: 1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the met
44、ric and inch-pound units, the inch-pound units shall rule. 2. Leads in true position within 0.010 inch (0.25 mm) R at NMC at seating plane. 3. Pin numbers shown for reference only. Pin 1 index is required. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted w
45、ithout license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88508 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 9 DSCC FORM 2234 APR 97 )MSB(out1BitDevice types All Device types All Case outline X Case outline X Terminal number Terminal symbol Terminal number Termi
46、nal symbol 1 Bit 12 out (LSB) 17 Clock rate 2 Bit 11 out 18 Ref out3 Bit 10 out 19 Clock out4 Bit 9 out 20 E.O.C. (status)5 Bit 8 out 21 Start convert6 Bit 7 out 22 Compar input7 Bit 6 out 23 Bipolar offset8 Bit 5 out 24 10 V range9 Bit 4 out 25 20 V range10 Bit 3 out 26 Analog com11 Bit 2 out 27 Ga
47、in ADJ12 Bit 1 out (MSB) 28 VCC13 29 Buffer output 14 Short cycle 30 Buffer input15 Digital com 31 VEE16 VDD32 Serial outputFIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-8850
48、8 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 10 DSCC FORM 2234 APR 97 Functional diagram Input connection table Input voltage range Without buffer Input Pin With buffer Input pin Connect these pins together Connect these pins together 0 to +5 V 24 22 to 25 23 to 26 30 22 to 25 23 to 26 29 to 24 0 to +10 V 24 - - - 23 to 26 30 - - - 23 to 26 29 to 24 2.5 V 24 22 to 25 23 to 22 30 22 to 25 23 to 22 29 to
