1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device type 02. Editorial changes in table I. 90-04-10 D. R. Cool B Add QD device type criteria. Add vendor CAGE 3V146. Update boilerplate to MIL-PRF-38535 requirements. - CFS 05-02-08 Thomas M. Hess The original first page of this drawing ha
2、s been replaced. REV SHET REV B B B B B SHEET 15 16 17 18 19 REV STATUS REV B B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Todd D. Creek DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Ray Monnin COLUMBUS, OHIO 43218-3990 htt
3、p:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Michael A. Frye MICROCIRCUIT, DIGITAL, NMOS, NUMERIC DATA PROCESSOR, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 88-06-15 AMSC N/A REVISION LEVEL SIZE A CAGE CODE 67268 5962-88
4、547 B SHEET 1 OF 19 DSCC FORM 2233 APR 97 5962-E070-05 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88547 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 AP
5、R 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-88547 01 Q X Drawing numb
6、er Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function Clock speed 01 8087-2 Numeric data processor (NDP) 8 MHz 02 8087 Numeric data processor (NDP) 5 MHz
7、1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style Q GDIP1-T40 or CDIP2-T40 40 Dual-in-line 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ra
8、tings. Voltage on any pin with respect to ground . -1.0 V dc to +7.0 V dc Storage temperature range -65C to +150C Maximum power dissipation (PD) 3.0 W Lead temperature (soldering, 10 seconds). +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ). +200C 1.4 Rec
9、ommended operating conditions. Supply voltage (VCC) +4.75 V dc to +5.25 V dc Case operating temperature range (TC) . -55C to +125C Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88547 DEFENSE SUPPLY CENTER C
10、OLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specifie
11、d, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interf
12、ace Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or www.dodssp.daps.mil or f
13、rom the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, howev
14、er, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this
15、 drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activi
16、ty approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein
17、. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. This drawing has been modified to allow the manufacturer to use the alternate die/fabrication requirements of paragraph A.3.2.2 of MIL-PRF-38535 or other alternative approve
18、d by the qualifying activity. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connec
19、tions. The terminal connections shall be as specified on figure 1. 3.2.3 Functional block diagram. The functional block diagram shall be as specified on figure 2. 3.2.4 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 3. 3.3 Electrical pe
20、rformance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full case operating temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STAND
21、ARD MICROCIRCUIT DRAWING SIZE A 5962-88547 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup a
22、re described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space
23、 limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ o
24、r “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. For product built in accordance with A.3.2.2 of MIL-PRF-38535, or as modified in the manufacturers QM plan, the “QD” certification mark shall be used in place of the “Q” or “QML” certification m
25、ark. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affi
26、rm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Not
27、ification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing. 3.9 Verification and review. DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documen
28、tation shall be made available onshore at the option of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88547 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DS
29、CC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TC +125C 4.75 V VCC 5.25 V unless otherwise specified Group A subgroups Device type Limits Unit Min Max Low level input voltage VIL0.5 1/ 0.8 V High level input voltage VIH2.0 VCC+ 0.5 1/ V Low level out
30、put voltage (Status lines and all others) VOLIOL= 2.0 mA 0.60 V High level output voltage VOHIOH= -400 A 1, 2, 3 2.4 V Quiescent supply current ICCVCC= 5.25 V 3 600 mA Input leakage current ILIVIN= 0.0 V or 5.5 V 10 A Output leakage current ILOVOUT= 0.45 V or 5.5 V 10 A Clock input low voltage VCL-0
31、.5 1/ 0.6 V Clock input high voltage VCH1, 2, 3 3.9 VCC+ 1.0 1/ V Input capacitance CIN10 pF Input/output buffer capacitance CI/O15 pFOutput capacitance COUTSee 4.3.1c 2/ 4 10 pF Functional tests See 4.3.1d 7, 8 All See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or netwo
32、rking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88547 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TC +125C 4.75
33、V VCC 5.25 V unless otherwise specified Group A subgroups Device type Limits Unit Min Max 01 125 500 CLK cycle period tCLCL02 200 500 ns 01 68 1/ CLK low time tCLCH02 2/3(tCLCL) - 15 ns 01 44 CLK high time tCHCL02 1/3(tCLCL) + 2 ns CLK rise time 1/ tCH1CH2All 10 ns CLK fall time 1/ tCL2CL101 20 Data
34、 in setup time tDVCL02 30 ns Data in hold time tCLDXAll 10 ns 01 68 READY setup time tRYHCH02 2/3(tCLCL) - 15 ns 01 20 READY hold time tCHRYX02 30 ns READY inactive to CLK tRYLCLAll -8 ns 01 15 RQ/GT setup time tGVCH02 30 ns 01 30 RQ/GT hold time tCHGX02 40 ns QS0-1setup time tQVCLAll 30 ns QS0-1hol
35、d time tCLQX10 Status active setup time tSACHAll 30 ns Status inactive setup time 1/ tSNCLSee figure 3. 9, 10, 11 All 30 ns See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88547
36、 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TC +125C 4.75 V VCC 5.25 V unless otherwise specified Group A subgroups Device type Limits Unit Min Max In
37、put rise time (except CLK) 1/ tILIHAll 20 ns Input fall time (except CLK) 1/ tIHIL12 ns 01 65 Ready active to status passive tRYHSH02 110 ns 01 10 1/ 60 Status active delay tCHSV02 10 1/ 110 ns 01 10 1/ 70 Status inactive delay tCLSH02 10 1/ 130 ns 01 10 1/ 60 Address valid delay tCLAV02 10 1/ 114 n
38、s Address hold time tCLAXAll 10 ns 01 tCLAX50 Address float delay 1/ tCLAZ02 tCLAX80 ns 01 10 1/ 60 Data valid delay tCLDV02 10 1/ 110 ns Data hold time tCHDXAll 10 ns 01 10 1/ 85 BUSY and INT valid delay tCHBVSee figure 3. 9, 10, 11 02 10 1/ 150 ns See footnotes at end of table. Provided by IHSNot
39、for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88547 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Sym
40、bol Conditions -55C TC +125C 4.75 V VCC 5.25 V unless otherwise specified Group A subgroups Device type Limits Unit Min Max 01 0 1/ 50 RQ/GT active delay tCLGL02 0 1/ 85 ns 01 0 1/ 50 RQ/GT inactive delay tCLGH02 0 1/ 85 ns Output rise time 1/ tOLOHAll 20 ns Output fall time 1/ tOHOLSee figure 3. 9,
41、 10, 11 All 12 ns 1/ Guaranteed to the limits specified herein if not tested. 2/ The capacitance measurements shall be made between the indicated terminal and ground at a frequency of 1 MHz at TCof +25C. The dc bias of the measuring instrument shall be less than 0.1 V. The ac signal amplitude shall
42、be less than 50 mV rms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88547 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 Device types: 01 and 02 Ca
43、se outline: Q Terminal number Terminal symbol Terminal number Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 GND AD14AD13AD12AD11AD10AD9AD8AD7AD6AD5AD4AD3AD2AD1AD0NC NC CLK GND 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 RESET READY BUSY QS1QS0S0S1S2NC NC RQ/GT0IN
44、T RQ/GT1BHE/S7A19/S6A18/S5A17/S4A16/S3AD15VCCNC = No connection FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88547 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 R
45、EVISION LEVEL B SHEET 10 DSCC FORM 2234 APR 97 FIGURE 2. Functional block diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88547 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL
46、 B SHEET 11 DSCC FORM 2234 APR 97 NOTE: CLincludes jig, probe, and stray capacitance. NOTE: AC testing inputs are driven at 2.4 V for a logic “1” and 0.45 V for a logic “0”. FIGURE 3. Switching waveforms and test circuit. Provided by IHSNot for ResaleNo reproduction or networking permitted without l
47、icense from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88547 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 12 DSCC FORM 2234 APR 97 Master Mode (with Bus Controller References) FIGURE 3. Switching waveforms and test circuit - Continued. Provided by IHSNot for
48、 ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88547 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 13 DSCC FORM 2234 APR 97 Master Mode (with Bus Controller References) FIGURE 3. Switching waveforms and test circuit - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88547 DEFENSE S
