1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add “Changes in accordance with NOR 5962-R257-92“. -car 92-07-10 M. L. Poelking B Update to reflect latest changes in format and requirements. Editorial changes throughout. -les 01-04-12 Raymond Monnin C Update drawing to current requirements. Ed
2、itorial changes throughout. - gap 08-12-05 Robert M. Heber The original first sheet of this drawing has been replaced. REV SHET REV SHET REV STATUS REV C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY Monica L. Poelking DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRA
3、WING CHECKED BY Ray Monnin COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Michael A. Frye MICROCIRCUIT, DIGITAL, BIPOLAR, ADVANCED LOW POWER SCHOTTKY TTL, 8-BIT IDENTITY AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE
4、 88-05-16 COMPARATOR, MONOLITHIC SILICON AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-88578 SHEET 1 OF 9 DSCC FORM 2233 APR 97 5962-E273-08 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88578 DEFEN
5、SE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Numbe
6、r (PIN). The complete PIN is as shown in the following example: 5962-88578 01 R X Drawing number Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54A
7、LS688 8-bit identity comparator 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 Dual-in-line S GDFP2-F20 or CDFP3-F20 20 Flat package 2 CQCC1-N20 20 Square leadless
8、chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. 1/ Supply voltage . -0.5 V dc to +7.0 V dc Input voltage (VIN) . -1.5 V dc at -18 mA to +7.0 V
9、dc Storage temperature range -65C to +150C Maximum power dissipation (PD) . 104.5 mW 2/ Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) +175C 1.4 Recommended operating conditions. Supply voltage range (VEE) +4.5 V
10、dc to +5.5 V dc Minimum high-level input voltage (VIH) +2.0 V dc Maximum low- level input voltage (VIL) 0.7 V dc Maximum high-level output current (IOH) . -1.0 mA Maximum low- level output current (IOL) . 12 mA Case operating temperature range (TC) . -55C to +125C _ 1/ Stresses above the absolute ma
11、ximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Maximum power dissipation is defined as VCCx ICC, and must withstand the added PDdue to short circuit test; e.g., I0S. Provided by IHSNot for ResaleNo re
12、production or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88578 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The
13、following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufactur
14、ing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Micro
15、circuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this dra
16、wing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance
17、 with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535
18、may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall n
19、ot affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design
20、, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth
21、 table shall be as specified on figure 2. 3.2.4 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified
22、 in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. Provided by IHSNot for ResaleNo reproduction o
23、r networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88578 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be ma
24、rked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance ma
25、rk. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate
26、 of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufact
27、urers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change.
28、 Notification of change to DSCC-VA shall be required for any change that affects this drawing. 3.9 Verification and review. DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made
29、 available onshore at the option of the reviewer. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devi
30、ces prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the pr
31、eparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as spe
32、cified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88578 DEFENSE SUPPLY C
33、ENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TC+125C Group A subgroups Limits Unit unless otherwise specified Min Max High level output voltage VOHVIH= +2.0 V, VCC= +4.5 V, VIL= 0.
34、7 V, IOH= -0.4 mA 1, 2, 3 2.5 V Low level output voltage VOLVIH= +2.0 V, VCC= +4.5 V, VIL= 0.7 V, IOH= 12 mA 1, 2, 3 0.4 V Input clamp voltage VICIIN= -18 mA, VCC= +4.5 V 1, 2, 3 -1.5 V High level input current IIH1VCC= +5.5 V, VIN= +2.7 V 1, 2, 3 20 A IIH2VCC= +5.5 V, VIN= +7.0 V 1, 2, 3 0.1 mA Low
35、 level input current IILVCC= +5.5 V, VIN= 0.4 V, 1, 2, 3 -0.1 mA Output current IOVCC= +5.5 V, VOUT= 2.25 V 1/ 1, 2, 3 -20 -112 mA Power supply current ICCVCC= +5.5 V 1, 2, 3 19 mA Functional tests See 4.3.1c 7, 8 tPLH19, 10, 11 3 17.5 ns Propagation delay time, P to Q P tPHL19, 10, 11 5 25 tPLH29,
36、10, 11 3 17.5 ns Propagation delay time, Q to Q P tPHL29, 10, 11 5 25 tPLH39, 10, 11 3 15 ns Propagation delay time, G to Q P tPHL3VCC= 4.5 V to 5.5 V CL= 50 pF 10% RL= 500 5% See figure 3 9, 10, 11 5 25 1/ The output conditions have been chosen to produce a current that closely approximates one hal
37、f of the true short circuit of the true short circuit output current, IOS. Not more than one output should be shorted at a time and the duration of the short circuit condition should not exceed one second. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-
38、,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88578 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 Device type 01 Case outlines R, S, and 2 Terminal number Terminal symbol 1 G 2 P0 3 Q0 4 P1 5 Q1 6 P2 7 Q2 8 P3 9 Q3 10 GND 11 P4 12 Q4 13 P5 14
39、 Q5 15 P6 16 Q6 17 P7 18 Q7 19 Q P 20 VCCConnection Description P0 - P7 Data Inputs Q0 - Q7 Data Inputs G Enable input Q P Output FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 596
40、2-88578 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Inputs Output Data P, Q Enable G Q P P = Q L L P Q L H P Q L H X H H H = High voltage level steady state L = Low voltage level steady state X = Irrelevant FIGURE 2. Truth table. NOTES: 1.
41、CLincludes probe and jig capacitance. 2. All input pulses have the following characteristics: PRR 10 MHz, duty cycle = 50%, tr= tf= 3 ns 1 ns. 3. The outputs are measured one at a time with one input transition per measurement. FIGURE 3. Switching waveforms and test circuit. Provided by IHSNot for R
42、esaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88578 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subg
43、roups (in accordance with MIL-STD-883, method 5005, table I) Interim electrical parameters (method 5004) - - - Final electrical test parameters (method 5004) 1*, 2, 3, 7, 8, 9, 10, 11 Group A test requirements (method 5005) 1, 2, 3, 7, 8, 9, 10, 11 Groups C and D end-point electrical parameters (met
44、hod 5005) 1, 2, 3 * PDA applies to subgroup 1. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shal
45、l be as specified in table II herein. b. Subgroups 4, 5, and 6 in table I, method 5005 of MIL-STD-883 shall be omitted. c. Subgroups 7 and 8 shall include verification of the truth table. 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b
46、. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall speci
47、fy the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TA= +125C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. Provided by IHSNot for ResaleNo reproduction or netw
48、orking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88578 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 9 DSCC FORM 2234 APR 97 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purpo
