1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A 1.3, absolute maximum ratings, change input voltage range. Editorial changes throughout. 90-08-14 W. Heckman B Update drawing to current requirements. Editorial changes throughout. - gap 07-07-05 Robert M. Heber The original first sheet of this d
2、rawing has been replaced. REV SHET REV SHET REV STATUS REV B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Greg A. Pitz DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Ray Monnin COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THI
3、S DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Michael A. Frye MICROCIRCUIT, DIGITAL, BIPOLAR, BIDIRECTIONAL TRANSCEIVERS, AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 88-03-08 MONOLITHIC SILICON AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-88604 SHEET 1 OF
4、 13 DSCC FORM 2233 APR 97 5962-E253-07 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88604 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.
5、1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-88604 01 K X Drawing number Device type (
6、see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 29861A High performance 10-bit bidirectional transceiver, 3-state 02 29863A High performance 9-bit bidirectional
7、transceiver, 3-state - 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style K GDFP2-F24 or CDFP3-F24 24 flat pack L GDIP3-T24 or CDIP4-T24 24 dual-in-line 3 CQCC1-N28 28 leadless square chip carrier
8、 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage range . -0.5 V dc to +7.0 V dc Input voltage range . -1.5 V dc to +6.0 V dc Storage temperature range . -65C to +150C Maximum power dissipation (PD) 1/ 2.2 W Lead temperatur
9、e (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) See MIL-STD-1835 Junction temperature (TJ) 150C/W DC output voltage range . -0.5 V dc to 5.5 V dc DC output current: Into output +100 mA DC output current: Out of output -50 mA DC input current range: Into input -30 mA to +5.0
10、 mA 1.4 Recommended operating conditions. Supply voltage range (VCC) . +4.5 V dc to +5.5 V dc Minimum high level input voltage (VIH) 2.0 V dc Maximum low level input voltage (VIL) . 0.7 V dc Case operating temperature range (TC) -55C to +125C _ 1/ Must withstand the added PDdue to short circuit test
11、; e.g., IOS. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88604 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Governmen
12、t specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION
13、MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Micro
14、circuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil;quicksearch/ or www.dodssp.daps.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order
15、of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item
16、 requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufact
17、urer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make
18、 modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option
19、is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal conne
20、ctions shall be as specified on figure 1. 3.2.3 Truth tables. The truth tables shall be as specified on figure 2. 3.2.4 Logic diagrams. The logic diagrams shall be as specified on figure 3. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MIC
21、ROCIRCUIT DRAWING SIZE A 5962-88604 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall
22、apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appe
23、ndix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1
24、 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow opt
25、ion is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply sh
26、all affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.
27、 3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing. 3.9 Verification and review. DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore
28、 documentation shall be made available onshore at the option of the reviewer. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and sh
29、all be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made
30、available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test paramet
31、ers shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-886
32、04 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Conditions Test Symbol -55C TC +125C Group A Device Limits Unit 4.5 V VCC 5.5 V subgroups type unless otherwise specified Min Max High level out
33、put VOHVCC= 4.5 V IOH= -15 mA 1, 2, 3 All 2.4 V voltage VIN= VIL or VIHOH= -24 mA 2.0 Low level output VOLVCC= 4.5 V, IOL= 32 mA, 1, 2, 3 All 0.5 V voltage VIN= VIHor VILInput clamp voltage VICVCC= 4.5 V, IIN= -18 mA 1, 2, 3 All -1.2 V Input hysteresis VHYST1, 2, 3 All 200 mV Low level input IILVCC=
34、 5.5 V, VIN= 0.4 V, 1, 2, 3 All -0.5 mA current OE input High level input IIHVCC= 5.5 V, VIN= 2.7 V, 1, 2, 3 All 50 A current OE input High input current IIVCC= 5.5 V, OE input 1, 2, 3 All 100 A VIN= 5.5 V I/O port 150 Output off-state IOZHVCC= 5.5 V VOUT= 2.7 V 1, 2, 3 All 100 A (high impedence) ou
35、tput current IOZLVOUT= 0.4 V -550 Output short IOSVCC= 5.5 V, VOUT= 0.0 V 1/ 1, 2, 3 All -75 -250 mA circuit current Bus leakage IOFFVCC= 0.0 V, VOUT= 2.9 V 1, 2, 3 All 100 A current Supply current ICCVCC= 5.5 V, Output logic low 1, 2, 3 All 140 mA Outputs unloaded Output logic high 115 Output logic
36、 Hi-Z 130 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88604 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I.
37、Electrical performance characteristics - Continued. Conditions Test Symbol -55C TC +125C Group A Device Limits Unit 4.5 V VCC 5.5 V subgroups type unless otherwise specified Min Max Propagation delay tPLHSee figure 4 9, 10, 11 All 9.0 ns from Ri to Ti CL= 50 pF, or Ti to Ri R1= 500 , Propagation del
38、ay tPHLR2= 500 , 9, 10, 11 All 9.0 ns from Ri to Ti or Ti to Ri Output enable time tPZH9, 10, 11 All 12.0 ns OET to Ti or OER to Ri Output enable time tPZL9, 10, 11 All 13.0 ns OET to Ti or OER to Ri Output disable time tPHZ9, 10, 11 All 10.0 ns OET to Ti or OER to Ri Output disable time tPLZ9, 10,
39、11 All 10.0 ns OET to Ti or OER to Ri 1/ Not more than one output should be shorted at a time. Duration should not exceed 1 second. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88604 DEFENSE SUPPLY CENTER
40、COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88604 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS,
41、 OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Inputs Outputs OET OER RiTiRiTiFunction L H L N/A N/A L Transmit L H H N/A N/A H Transmit H L N/A L L N/A Receive H L N/A H H N/A Receive H H X X Z Z Hi-Z Device type 02 Inputs Outputs OET1OET2OER1OER2RiTiRiTiFunction L L
42、 H X L N/A N/A L Transmit L L X H L N/A N/A L Transmit H X L L N/A L L N/A Receive X H L L N/A L L N/A Receive L L H X H N/A N/A H Transmit L L X H H N/A N/A H Transmit H X L L N/A H H N/A Receive X H L L N/A H H N/A Receive H X H X X X Z Z Hi-Z X H X H X X Z Z Hi-Z H = High X = Dont care L = Low N/
43、A = Not applicable Z = High impedance FIGURE 2. Truth tables. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88604 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC FORM
44、2234 APR 97 FIGURE 3. Logic diagrams. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88604 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 10 DSCC FORM 2234 APR 97 Parameter S
45、 position tPLHOpen tPHLOpen tPHZOpen tPZHOpen tPLZClosed tPZLClosed Switch positions for parameter testing. FIGURE 4. Switching waveforms and test circuits. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-886
46、04 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 11 DSCC FORM 2234 APR 97 NOTE: Pulse generator for all pulses, rate 1.0 MHz; Zo= 50 ; tr 1.5 ns; tf 2.5 ns. FIGURE 4. Switching waveforms and test circuits - Continued. Provided by IHSNot for ResaleNo reproduction or
47、networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88604 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 12 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance wi
48、th MIL-STD-883, method 5005, table I) Interim electrical parameters (method 5004) - - - Final electrical test parameters (method 5004) 1*, 2, 3, 7*, 8, 9, 10, 11 Group A test requirements (method 5005) 1, 2, 3, 7, 8, 9, 10, 11 Groups C and D end-point electrical parameters (method 5005) 1, 2, 3 * PDA applies to subgroups 1 and 7.
