1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add vendor CAGE F8859. Add device class V criteria. Editorial changes throughout. jak 99-09-23 Monica L. Poelking B Correct paragraph 1.3 and test conditions in table I. Add case outline X. Add table III, delta limits. Editorial changes throughou
2、t. LTG 00-06-22 Monica L. Poelking C Correct table II. Update boilerplate to MIL-PRF-38535 requirements. jak 02-01-25 Thomas M. Hess D Add vendor CAGE number 3V146. Update the boilerplate paragraphs to current requirements of MIL-PRF-38535. MAA 09-03-11 Thomas M. Hess First page of this drawing has
3、been changed REV SHEET REV D D SHEET 15 16 REV STATUS REV D D D D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY D. A. DiCenzo STANDARD MICROCIRCUIT DRAWING CHECKED BY Charles Reusing DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.d
4、la.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Michael A. Frye MICROCIRCUIT, DIGITAL, HIGH-SPEED CMOS, 1-OF-8 DECODER/DEMULTIPLEXER WITH ADDRESS LATCH, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 88-06-23 AMSC N/A REVISION LEVEL D SIZE
5、A CAGE CODE 67268 5962-88606 SHEET 1 OF 16 DSCC FORM 2233 APR 97 5962-E133-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88606 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SH
6、EET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identif
7、ying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following examples. For device classes M and Q: 5962-88606 01 E A_ Drawing number Device type Case outline Lead finish (see 1.2.2) (see 1.2.4) (see 1.
8、2.5) For device class V: 5962 - 88606 01 V X A Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices mee
9、t the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The
10、device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54HC237 1-of-8 decoder/demultiplexer with address latch 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as listed below. Since
11、 the device class designator has been added after the original issuance of this drawing, device classes M and Q designators will not be included in the PIN and will not be marked on the device. Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD
12、-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88606 D
13、EFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line F
14、 GDFP2-F16 or CDFP3-F16 16 Flat pack X CDFP4-F16 16 Flat pack 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply volt
15、age range (VCC) -0.5 V dc to +7.0 V dc DC input voltage range (VIN) -0.5 V dc to VCC+0.5 V dc DC output voltage range (VOUT) . -0.5 V dc to VCC+0.5 V dc Input clamp diode current (IIK) 20 mA Output clamp diode current (IOK) 20 mA DC output current 25 mA DC VCCor GND current . 50 mA Storage temperatu
16、re range (TSTG) . -65C to +150C Maximum power dissipation (PD): 500 mW 4/ Lead temperature (soldering, 10 seconds). +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) +175C 5/ 1/ Stresses above the absolute maximum rating may cause permanent damage to the de
17、vice. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the full specified VCC range and case temperature range of -55C to +125C. 4
18、/ For TC= +100C to +125C, derate linearly at 12 mW/C. 5/ Maximum junction temperature shall not be exceeded except for allowable short duration burn-in screening conditions in accordance with method 5004 of MIL-STD-883. Provided by IHSNot for ResaleNo reproduction or networking permitted without lic
19、ense from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88606 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 1.4 Recommended operating conditions. 1/ 2/ Supply voltage range (VCC) +2.0 V dc to +6.0 V dc Case operating temperature range (TC
20、) -55C to +125C Input rise or fall time (tr, tf): VCC= 2.0 V 0 to 1000 ns VCC= 4.5 V 0 to 500 ns VCC= 6.0 V 0 to 400 ns Minimum setup time, data to enable (ts): TC= +25C: VCC= 2.0 V 125 ns VCC= 4.5 V 25 ns VCC= 6.0 V 21 ns TC= -55C to +125C: VCC= 2.0 V 150 ns VCC= 4.5 V 30 ns VCC= 6.0 V 26 ns Minimu
21、m hold time, enable to data (th): TC= +25C: VCC= 2.0 V 65 ns VCC= 4.5 V 13 ns VCC= 6.0 V 11 ns TC= -55C to +125C: VCC= 2.0 V 75 ns VCC= 4.5 V 15 ns VCC= 6.0 V 13 ns Minimum reset clock pulse width (tw): TC= +25C: VCC= 2.0 V 100 ns VCC= 4.5 V 20 ns VCC= 6.0 V 17 ns TC= -55C to +125C: VCC= 2.0 V 120 n
22、s VCC= 4.5 V 24 ns VCC= 6.0 V 20 ns 1/ Unless otherwise noted all voltages are referenced to GND. 2/ The limits for the parameters specified herein shall apply over the full specified VCC range and case temperature range of -55C to +125C. Provided by IHSNot for ResaleNo reproduction or networking pe
23、rmitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88606 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, st
24、andards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification
25、for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies o
26、f these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following document(s) form a part of this document to the extent speci
27、fied herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. ELECTRONIC INDUSTRIES ALLIANCE (EIA) JEDEC Standard No. 7-A - Standard for Description of 54/74HCXXXX and 54/74HCTXXXX High-Speed CMOS Devices. (Copies of these documents are avail
28、able online at http:/www.eia.org or from the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834.) 2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in t
29、his document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the
30、device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as speci
31、fied herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be i
32、n accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Switching waveforms and test c
33、ircuit. The switching waveforms and test circuit shall be as specified in figure 4. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88606 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVE
34、L D SHEET 6 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics and post-irradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and post-irradiation parameter limits are as specified in table I and shall apply over the full case opera
35、ting temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufactur
36、ers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device clas
37、ses Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark fo
38、r device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For devic
39、e class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm tha
40、t the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-
41、38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this dra
42、wing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be m
43、ade available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 36 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted wi
44、thout license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88606 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits Test Symbol Test conditions 1/ -55C TC +125C unless otherwise spe
45、cified Group A subgroups Min Max Unit VCC= 2.0 V 1.9 VCC= 4.5 V 4.4 VIN= VIHminimum or VILmaximum IOH= -20 A VCC= 6.0 V 1, 2, 3 5.9 1 3.98 VIN= VIHminimum or VILmaximum IOH= -4.0 mA VCC= 4.5 V 2, 3 3.7 1 5.48 High level output Voltage VOHVIN= VIHminimum or VILmaximum IOH= -5.2 mA VCC= 6.0 V 2, 3 5.2
46、 V VCC= 2.0 V 0.1 VCC= 4.5 V 0.1 VIN= VIHminimum or VILmaximum IOL= +20 A VCC= 6.0 V 1, 2, 3 0.1 1 0.26 VIN= VIHminimum or VILmaximum IOL= +4.0 mA VCC= 4.5 V 2, 3 0.4 1 0.26 Low level output Voltage VOLVIN= VIHminimum or VILmaximum IOL= +5.2 mA VCC= 6.0 V 2, 3 0.4 V VCC= 2.0 V 1.5 VCC= 4.5 V 3.15 Hi
47、gh level input Voltage VIH 2/ VCC= 6.0 V 1, 2, 3 4.2 V VCC= 2.0 V 0.3 VCC= 4.5 V 0.9 Low level input voltage VIL 2/ VCC= 6.0 V 1, 2, 3 1.2 V Input capacitance CINVIN= 0.0 V, TC= +25C See 4.3.1d 4 10.0 pF See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permit
48、ted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88606 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Test conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Min Max Unit 1 8.0 Quiescent supply current ICCVCC= 6.0 V, VIN= VCCor
