1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Removed vendor CAGE 61772 from device types 01YX and 02YX. Technical change was made in table I. Editorial changes throughout. 90-07-24 William K. Heckman B Changes in accordance with NOR 5962-R186-94. 94-05-10 Monica L. Poelking C Add device typ
2、e 03. Add vendor CAGE 0DKS7 for device type 03. Update boilerplate to MIL-PRF-38535 requirements. - CFS 03-02-03 Thomas M. Hess D Update boilerplate to current MIL-PRF-38535 requirements. - CFS 08-05-05 Thomas M. Hess REV SHET REV D SHET 15 REV STATUS REV D D D D D D D D D D D D D D OF SHEETS SHEET
3、1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Tim H. Noh DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Tim H. Noh COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY William K. Heckman MICROCIRCUIT, DIGIT
4、AL, 16-BIT CMOS MICROPROGRAM SEQUENCER, MONOLITHIC AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 01 August 1988 SILICON AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-88643 SHEET 1 OF 15 DSCC FORM 2233 APR 97 5962-E351-08 Provided by IHSNot for ResaleNo reproduction or netwo
5、rking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88643 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class
6、 level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-88643 01 X X Drawing number Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type(s). The device ty
7、pe(s) identify the circuit function as follows: Device type Generic number Circuit function 01 49C410 16-bit CMOS microprogram sequencer with 33 deep stack 02 49C410A 16-bit CMOS microprogram sequencer with 33 deep stack 03 49C410 16-bit CMOS microprogram sequencer with 33 deep stack 1.2.2 Case outl
8、ines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X GDIP1-T48 or CDIP2-T48 48 Dual-in-line Y See figure 1 48 Square leadless chip carrier Z See figure 1 48 Flat pack 1.2.3 Lead finish. The lead finish is as specifi
9、ed in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. 1/ Supply voltage (VCC) -0.5 V dc to +7.0 V dc DC output current. +30 mA Power dissipation (PD) 2/. 1.0 W Storage temperature -65C to +150C Lead temperature (soldering, 10 seconds). 300C Junction temperature (TJ). +175C Thermal resistanc
10、e, junction-to-case (JC): Case X See MIL-STD-1835 Case Y 20C/W Case Z 22C/W 1.4 Recommended operating conditions. Supply voltage (VCC) +4.5 V dc to +5.5 V dc Case operating temperature (TC) . -55C to +125C Minimum high-level input voltage (VIH). +2.0 V dc Maximum low-level input voltage (VIL) +0.8 V
11、 dc _ 1/ All voltages are referenced to GND. 2/ Must withstand the added PDdue to short circuit test, e.g., IOS. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88643 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS,
12、OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of t
13、hese documents are those cited in the solicitation or contact. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electr
14、onic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Stand
15、ardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersede
16、s applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that
17、 is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval i
18、n accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “Q
19、ML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. T
20、he case outlines shall be in accordance with 1.2.2 herein and on figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Instruction set. The instruction set shall be as specified on figure 3. 3.2.4 Logic diagram. The logic diagram shall be as specifie
21、d on figure 4. 3.2.5 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 5. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply
22、 over the full case operating temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88643 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 3
23、.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in
24、 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator
25、“C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certifica
26、te of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 and QML-38535 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturers product
27、 meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification
28、 of change to DSCC-VA shall be required for any change that affects this drawing. 3.9 Verification and review. DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available on
29、shore at the option of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88643 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Elec
30、trical performance characteristics. Limits Test Symbol Conditions -55C TC +125C +4.5 V dc VCC +5.5 V dc unless otherwise specified Group A subgroups Device type Min Max Unit IOH= -300 A 4.3 High level output voltage VOHVCC= 4.5 V VIL= 0.8 V VIH= 2.0 V IOH= -12 mA 1, 2, 3 All 2.4 V IOH= 300 A 0.2 Low
31、 level output voltage VOLVCC= 4.5 V VIL= 0.8 V VIH= 2.0 V IOH= 12 mA 1, 2, 3 All 0.5 V High level input current IIHVCC= 5.5 V, VIN= 5.5 V 1, 2, 3 All 5.0 A Low level input current IILVCC= 5.5 V, VIN= GND 1, 2, 3 All -5.0 A Short circuit output current IOSVCC= 4.5 V, VOUT= GND 1/ 1, 2, 3 All -30 mA V
32、OUT= 0 V -10 Off-state high impedance output current IOZVCC= 5.5 V VOUT= 5.5 V 1, 2, 3 All 10 A 01, 02 50 Quiescent power supply current (CMOS inputs) ICCQHVCC= 5.5 V, VIL 0.2 V, VIH 5.3 V, fCP= 0, CP = H 1, 2, 3 03 5.0 mA 01, 02 50 Quiescent power supply current (CMOS inputs) ICCQLVCC= 5.5 V, VIL 0
33、.2 V, VIH 5.3 V, fCP= 0, CP = L 1, 2, 3 03 5.0 mA 01, 02 0.5 Quiescent power supply current (TTL inputs) 2/ ICCTVCC= 5.5 V, VIN= 3.4 V, fCP= 0 1, 2, 3 03 1.3 mA/ input 01, 02 3.0 Dynamic power supply current ICCDVCC= 5.5 V, VIL 0.2 V, VIH= 5.3 V, outputs open, OE = L 1, 2, 3 03 6.0 mA/ MHz VCC= 5.5
34、V, fCP= 10 MHz, outputs open, VIH 5.3 V, VIL 0.2 V, OE = L, CP = 50% duty cycle 80 Total power supply current 3/ ICCVCC= 5.5 V, fCP= 10 MHz, outputs open, VIH= 3.4 V, VIL= 0.4 V, OE = L, CP = 50% duty cycle 1, 2, 3 All 90 mA Input capacitance CINSee 4.3.1c 4 All 12 pF Output capacitance COUTSee 4.3.
35、1c 4 All 15 pF Functional tests See 4.3.1d 7, 8 All See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88643 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL
36、 D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Conditions -55C TC +125C +4.5 V dc VCC +5.5 V dc unless otherwise specified Group A subgroups Device type Min Max Unit 01 16 02 7.0 Setup time D1to R tS19, 10, 11 03 10 ns 01 30 02 15 Set
37、up time D1to PC tS29, 10, 11 03 20 ns 01 38 02 25 Setup time I0-3tS39, 10, 11 03 40 ns 01, 03 35 Setup time CC tS49, 10, 11 02 18 ns 01, 03 35 Setup time CCEN tS59, 10, 11 02 18 ns 01 18 02 7.0 Setup time CI tS69, 10, 11 03 34 ns 01 20 02 12 Setup time RLD tS79, 10, 11 03 22 ns Hold time D1to R tH19
38、, 10, 11 All 0 ns Hold time D1to PC tH29, 10, 11 All 0 ns Hold time I0-3tH39, 10, 11 All 0 ns Hold time CC tH49, 10, 11 All 0 ns Hold time CCEN tH59, 10, 11 All 0 ns Hold time CI tH69, 10, 11 All 0 ns Hold time RLD tH79, 10, 11 All 0 ns 01 25 02 15 Propagation delay D0-11to Y tPD1See figure 5. 4/ 9,
39、 10, 11 03 20 ns See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88643 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TA
40、BLE I. Electrical performance characteristics - Continued. Limits Test Symbol Conditions -55C TC +125C +4.5 V dc VCC +5.5 V dc unless otherwise specified Group A subgroups Device type Min Max Unit 01 40 02 25 Propagation delay I0-3to Y tPD29, 10, 11 03 33 ns 01 36 02 20 Propagation delay CC to Y tPD
41、39, 10, 11 03 30 ns 01, 03 36 Propagation delay CCEN to Y tPD49, 10, 11 02 20 ns 01 46 Propagation delay CP to Y tPD59, 10, 11 02, 03 33 ns 01 25 Propagation delay OE to Y (enable) tPD69, 10, 11 02, 03 13 ns 01 30 Propagation delay OE to Y (disable) tPD79, 10, 11 02, 03 13 ns 01 35 Propagation delay
42、 I0-3to PL, VECT, MAP tPD89, 10, 11 02, 03 15 ns 01 35 Propagation delay CP to FULL tPD99, 10, 11 02, 03 25 ns 01 25 02 20 Clock low time tPW19, 10, 11 03 32 ns 01 25 02 20 Clock high time tPW29, 10, 11 03 8 ns 01 51 Clock period tPSee figure 5. 4/ 9, 10, 11 02, 03 40 ns 1/ Not more than one output
43、should be shorted at one time. Duration of the short circuit test should not exceed one second. 2/ ICCTis derived by measuring the total current with all the inputs tied together at 3.4 V, subtracting out ICCQH, then dividing by the total number of inputs. 3/ ICC= ICCQH(CDH) + ICCQL(1 - CDH) + ICCT(
44、NTx DH) + ICCD(fCP). Where: CDH= Clock duty cycle high period; DH= Data duty cycle TTL high period (VIN = 3.4 V); NT= Number of dynamic inputs driven at TTL levels; fCP= Clock input frequency. 4/ Unless otherwise specified, the input pulse level shall be between 0 V to 3.0 V, input rise/fall times s
45、hall be 1.0 V/ns and input and output timing reference levels shall be 1.5 V. 5/ Disable time is measured to 0.5 V change on output voltage level with CL= 5 pF. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962
46、-88643 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 APR 97 Case Y Inches Millimeters Symbol Min. Max. Min. Max. A .055 .120 1.397 3.048 A1 .045 .090 1.143 2.286 B1 .017 .023 0.432 0.584 B2 .072 REF 1.829 REF B3 .006 .022 0.152 0.559 D/E .554 .572 1
47、4.072 14.529 D1/E1 .440 BSC 11.176 BSC D2/E2 .220 REF 5.588 REF D3/E3 .500 .535 12.700 13.589 e .040 BSC 1.016 BSC e1 .015 - 0.381 - h .012 R 0.305 R J .020 REF 0.508 REF L .033 .047 0.838 1.194 L1 .033 .047 0.838 1.194 L2 .077 .093 1.956 2.362 L3 .003 .015 0.076 0.381 ND/NE 12 12 Number of leads (N
48、) 48 48 FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88643 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 9 DSCC FORM 2234 APR 97 Case Z Inches Millimeters Symbol Min. Max. Min. Max. A .089 .108 2.261 2.743 A1 .079 .096 2.007 2.438 A2 .058 .073 1.473 1.854 b .018 .022 0.457 0.559 c .008 .010 0.203 0.254 D/E - .750 - 19.050 D1/E1 .100 REF 2.540 REF D2/E2 .550 BSC 13.
