1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update drawing to reflect current requirements. New boilerplate. -ljs 00-11-01 Ray Monnin B Update drawing to current requirements. Editorial changes throughout. - gap 08-04-25 Robert M. Heber The original first sheet of this drawing has been rep
2、laced. REV SHET REV SHET REV STATUS REV B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY Christopher A. Rauch DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Ray Monnin COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE
3、BY ALL DEPARTMENTS APPROVED BY Michael A. Frye MICROCIRCUIT, DIGITAL, BIPOLAR, ADVANCED SCHOTTKY, TTL, HEX DRIVERS, MONOLITHIC AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 88-09-12 SILICON AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-88731 SHEET 1 OF 9 DSCC FORM 2233 APR
4、97 5962-E033-08 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88731 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing d
5、escribes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-88731 01 C X Drawing number Device type (see 1.2.1) Case outline
6、(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54AS1034 Hex drivers 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descrip
7、tive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line D GDFP1-F14 or CDFP2-F14 14 Flat pack 2 CQCC1-N20 20 Square chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage range -0.5 V dc mini
8、mum to +7.0 V dc maximum Input voltage . -1.2 V dc at -18 mA to +7.0 V dc Storage temperature . -65C to +150C Maximum power dissipation (PD) 1/ . 192.5 mW Lead temperature (soldering, 10 seconds) . +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) . +175C 1
9、.4 Recommended operating conditions. Supply voltage range (VCC) . +4.5 V dc minimum to +5.5 V dc maximum Minimum high level input voltage (VIH) . 2.0 V dc Maximum low level input voltage (VIL) 0.8 V dc Case operating temperature range (TC) . -55C to +125C _ 1/ Maximum power dissipation is defined as
10、 VCCx ICC, and the device must withstand the added PDdue to short circuit test, e.g., IO. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88731 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISIO
11、N LEVEL B SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are thos
12、e cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Ou
13、tlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Or
14、der Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and
15、regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qual
16、ified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-
17、PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark
18、 in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall
19、 be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Test circuit and switching waveforms The test circuit and switching waveforms shall be as specified
20、 on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall
21、 be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88731 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43
22、218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN numb
23、er is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C”
24、 shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-
25、103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conf
26、ormance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing. 3.9 Verification and review. DSCC, DSCCs agent, and t
27、he acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accord
28、ance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test co
29、ndition A or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accorda
30、nce with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IH
31、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88731 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Con
32、ditions 1/ -55C TC+125C Group A subgroups Limits Unit unless otherwise specified Min Max IOH= -2 mA 2.5 IOH= -3 mA 2.4 High level output voltage VOHVCC= 4.5 V, VIL= 0.8 V, VIH= 2.0 V 2/ IOH= -40 mA 1, 2, 3 2.0 V Low level output voltage VOLVCC= 4.5 V, VIH= 2.0 V, VIL= 0.8 V, IOL= 40 mA 2/ 1, 2, 3 0.
33、5 V Input clamp voltage VICVCC= 4.5 V, IIN= -18 mA 1, 2, 3 -1.2 V Low level input current IIL VCC= 5.5 V, VIN= 0.4 V All other inputs = 4.5 V 1, 2, 3 -0.5 mA IIH1 VCC= 5.5 V, VIN= 2.7 V All other inputs = 0.0 V 20 A High level input current IIH2 VCC= 5.5 V, VIN= 7.0 V All other inputs = 0.0 V 1, 2,
34、3 0.1 mA Output current IOVCC= 5.5 V, VOUT=2.25 V 3/ 1, 2, 3 -50 -200 mA ICCH VCC= 5.5 V, VIN= 4.5 V 15 Supply current ICCL VCC= 5.5 V, VIN= 0.0 V 1, 2, 3 35 mA Functional tests See 4.3.1c 7, 8 Propagation delay time, A to Y tPLH VCC= 4.5 to 5.5 V RL= 500 , CL= 50 pF 9, 10, 11 1 6.5 ns tPHL See figu
35、re 3 4/ 1 6.5 1/ Unused inputs that do not directly control the pin under test must be 2.5 V dc or 0.4 V. No unused inputs shall exceed 5.5 V or go less than 0.0 V. No inputs shall be floated. 2/ All outputs must be tested. In the case where only one input at VILmaximum or VIHminimum produces the pr
36、oper output state, the test must be performed with each input being selected as the VILmaximum or VIHminimum input. 3/ The output conditions have been chosen to produce a current that closely approximates one-half of the true short circuit output current, IOS. Not more than one output will be tested
37、 at one time and the duration of the test condition shall not exceed one second. 4/ Propagation delay limits are based on single output switching. Unused inputs = 3.5 V or 0.3 V. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT D
38、RAWING SIZE A 5962-88731 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 Case outlines C and D 2 Terminal number Terminal symbol 1 1A NC 2 1Y 1A 3 2A 1Y 4 2Y 2A 5 3A NC 6 3Y 2Y7 GND NC 8 4Y 3A 9 4A 3Y 10 5Y GND 11 5A NC 12 6Y 4Y 13 6A 4A 14 VCC
39、5Y 15 NC16 5A 17 NC 18 6Y19 6A 20 VCCNC = No connection FIGURE 1. Terminal connections. Input Output A B H H L L L = Low voltage level H = High voltage level FIGURE 2. Truth table (each level). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD
40、 MICROCIRCUIT DRAWING SIZE A 5962-88731 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 NOTES: 1. CLincludes probe and jig capacitance. 2. All input pulses have the following characteristics: PRR 10 MHz, duty cycle = 50%, tr= tf= 3 ns 1 ns. 3.
41、The outputs are measured one at a time with one transition per measurement. FIGURE 3. Test circuit and switching waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88731 DEFENSE SUPPLY CENTER COLUMBUS
42、 COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Interim electrical parameters (method 5004) - - - Final electrical test parameters (method
43、5004) 1*, 2, 3, 7, 8, 9, 10, 11 Group A test requirements (method 5005) 1, 2, 3, 7, 8, 9, 10, 11 Groups C and D end-point electrical parameters (method 5005) 1, 2, 3 * PDA applies to subgroup 1. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 500
44、5 of MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 4, 5, and 6 in table I, method 5005 of MIL-STD-883 shall be omitted. c. Subgroups 7 and 8 shall inclu
45、de verification of the truth table. 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A or D. The test circuit shall be maintained by the manufacturer und
46、er document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TA= +125C,
47、minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88731 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVIS
48、ION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-prepared specification or drawing. 6.3 C
