1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes to 1.2.1. Made technical changes to table I. Added a square chip carrier package to 1.2.2. Changes to figure 1 and figure 4. Added vendor CAGE number 59621 for the square chip carrier package. 91-10-18 Monica L. Poelking B Added device ty
2、pes 05 through 08. Made technical changes to table I. Added CAGE number 65896 for device types 05 through 08. Editorial changes throughout. 92-06-19 Tim Noh C Changes made in accordance with NOR 5962-R310-92 92-09-11 Monica L. Poelking D Changes made in accordance with NOR 5962-R113-93 93-03-29 Moni
3、ca L. Poelking E Changes made in accordance with NOR 5962-R199-96 96-09-25 Monica L. Poelking F Updated boilerplate and made editorial changes throughout. - LTG 00-05-30 Monica L. Poelking G Updated boilerplate to MIL-PRF-38535 requirements. - CFS 05-08-15 Thomas M. Hess REV SHET REV G SHET 15 REV S
4、TATUS REV G G G G G G G G G G G G G G OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Phu Nguyen DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Tim H. Noh COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTME
5、NTS APPROVED BY Monica L. Poelking MICROCIRCUIT, DIGITAL, CMOS, 8 X 8 AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 88-11-07 MULTIPLIER, MONOLITHIC SILICON AMSC N/A REVISION LEVEL G SIZE A CAGE CODE 67268 5962-88739 SHEET 1 OF 15 DSCC FORM 2233 APR 97 5962-E415-05 Provided by IHSNo
6、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88739 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for
7、MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-88739 01 Q X Drawing number Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3
8、)1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function Multiply time 01 TMC208KV Twos complement 8 x 8 multiplier 70 ns 02 TMC208KV1 Twos complement 8 x 8 multiplier 50 ns 03 TMC28KUV Unsigned magnitude 8 x 8 multiplier 70 ns 0
9、4 TMC28KUV1 Unsigned magnitude 8 x 8 multiplier 50 ns 05 LMU0860 Twos complement 8 x 8 multiplier 60 ns 06 LMU0845 Twos complement 8 x 8 multiplier 45 ns 07 LMU8U60 Unsigned magnitude 8 x 8 multiplier 60 ns 08 LMU8U45 Unsigned magnitude 8 x 8 multiplier 45 ns 1.2.2 Case outline(s). The case outline(
10、s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style Q GDIP1-T40 or CDIP2-T40 40 Dual-in-line X CQCC1-N44 44 Square leadless chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximu
11、m ratings. Supply voltage range (VDD) -0.5 V dc to +7.0 V dc DC voltage applied to outputs: Devices 01, 02, 03, 04 . -0.5 V dc to VDD+0.5 V dc Devices 05, 06, 07, 08 . -3.0 V dc to +7.0 V dc DC input voltage: Devices 01, 02, 03, 04 . -0.5 V dc to VDD+0.5 V dc Devices 05, 06, 07, 08 . -3.0 V dc to +7
12、.0 V dc Maximum power dissipation (PD) . 550 mW 1/ Lead temperature (soldering 10 seconds) . 300C Junction temperature (TJ) 175C Thermal resistance, junction to case (JC) . See MIL-STD-1835 Storage temperature range (TSTG) . -65C to +150C _ 1/ Must withstand the added PDdue to short circuit test; e.
13、g., IOS. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88739 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 3 DSCC FORM 2234 APR 97 1.4 Recommended operating conditions. Sup
14、ply voltage (VDD) 4.5 V dc to 5.5 V dc Output high current (IOH) -2.0 mA maximum Output low current (IOL): Devices 01, 02, 03, 04 4.0 mA maximum Devices 05, 06, 07, 08 8.0 mA maximum Input high voltage (VIH). 2.0 V minimum Input low voltage (VIL). 0.8 V maximum Case operating temperature range (TC)
15、. -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitat
16、ion or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DE
17、FENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Av
18、enue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a spe
19、cific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listi
20、ng (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow
21、 as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-
22、PRF-38535 is required to identify when the QML flow option is used. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88739 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 4 DSCC
23、 FORM 2234 APR 97 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The termi
24、nal connections shall be as specified on figure 1. 3.2.3 Input/output data format. The input/output data format shall be as specified on figure 2. 3.2.4 Block diagram. The block diagram shall be as specified on figure 3. 3.2.5 Test circuit and switching waveforms. The test circuit and switching wave
25、forms shall be as specified on figure 4. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electri
26、cal test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers
27、PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices b
28、uilt in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a ma
29、nufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and t
30、he requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change tha
31、t affects this drawing. 3.9 Verification and review. DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. Provided by IHSNot fo
32、r ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88739 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions
33、 -55C TC +125C 4.5 V VDD 5.5 V 1/ unless otherwise specified Group A subgroups Device type Limits Unit Min Max 01,02 03,04 2.0 3/ Input high voltage VIHVDD= 5.5 V 1, 2, 3 05,06 07,08 2.0 V 01,02 03,04 0.8 3/ Input low voltage VILVDD= 5.5 V 1, 2, 3 05,06 07,08 0.8 V 01,02 03,04 2.4 High level output
34、voltage VOHVDD= 4.5 V, IOH= -2.0 mA 1, 2, 3 05,06 07,08 2.4 V IOL= 4.0 mA 01,02 03,04 0.4 Low level output voltage VOLVDD= 4.5 V IOL= 8.0 mA 1, 2, 3 05,06 07,08 0.5 V 01,02 03,04 -10 Input low current IILVDD= 5.5 V VIN= 0.0 V 1, 2, 3 05,06 07,08 -20 A 01,02 03,04 +10 Input high current IIHVDD= 5.5 V
35、 VIN= VDD1, 2, 3 05,06 07,08 +20 A 01,02 03,04 -40 Output leakage current, low IOZLVDD= 5.5 V VIN= 0.0 V 1, 2, 3 05,06 07,08 -20 A 01,02 03,04 +40 Output leakage current, high IOZHVDD= 5.5 V VIN= VDD1, 2, 3 05,06 07,08 +20 A 01,02 03,04 -100 Output short circuit current 2/ 3/ IOSVDD= 5.5 V 1, 2, 3 0
36、5,06 07,08 -125 mA See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88739 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 6 DSCC FORM 2234 APR 97
37、TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TC +125C 4.5 V VDD 5.5 V 1/ unless otherwise specified Group A subgroups Device type Limits Unit Min Max VIN= 0.0 V 01,02 03,04 5.0 Supply current, quiescent IDDQVDD= 5.5 V 4/ 1, 2, 3 05,06 07,08 1.0 mA VDD= 5.5
38、 V, TRIM, TRIL = 5.0 V, f = 2 MHz 01,02 03,04 10 IDDUVDD= 5.5 V, TRIM, TRIL = 5.0 V, f = 20 MHz 3/ 1, 2, 3 01,02 03,04 100 mA Supply current, dynamic IDDVDD= 5.5 V, TRIM, TRIL = 5.0 V, f = 5 MHz 1, 2, 3 05,06 07,08 24 mA Input capacitance CIN4 All 10 pF Output capacitance COUTf = 1.0 MHz TC= 25C See
39、 4.3.1c 4 All 10 pF Functional testing 5/ VDD= 4.5 V to 5.5 V See 4.3.1d 7, 8 All 9, 10, 11 01,03 70 10 02,04 50 9, 10, 11 05,07 60 Multiply time tMPY9, 10, 11 06,08 45 ns 9, 10, 11 01,03 45 10 02,04 30 Output delay tD9, 10, 11 05,06 07,08 22 ns 9, 10, 11 01,03 30 10 02,04 25 Input setup time tS9, 1
40、0, 11 05,06 07,08 15 ns Input hold time 3/ tH9, 10, 11 All 0 ns 9, 10, 11 01,02 03,04 15 9, 10, 11 05,07 20 Clock pulse width, high tPWHSee figure 4 5/ VDD= 4.5 V CL= 20 pF minimum 9, 10, 11 06,08 15 ns See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitt
41、ed without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88739 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TC +125C 4.5 V VDD 5.5 V 1/
42、 unless otherwise specified Group A subgroups Device type Limits Unit Min Max 9, 10, 11 01,02 03,04 15 9, 10, 11 05,07 20 Clock pulse width, low tPWLSee figure 4. 5/ VDD= 4.5 V CL= 20 pF minimum 3/ 9, 10, 11 06,08 15 ns 9, 10, 11 01,03 45 10 02,04 25 Three-state output enable time tENA9, 10, 11 05,0
43、6 07,08 24 ns 9, 10, 11 01,03 45 10 02,04 25 Three-state output disable time tDISSee figure 4. 5/ VDD= 4.5 V CL= 20 pF minimum 9, 10, 11 05,06 07,08 22 ns 1/ Unless otherwise specified, all testing shall be conducted under worst case conditions. 2/ One output to ground, 1 second duration maximum, ou
44、tput high. 3/ Guaranteed, if not tested, to the specified limits. 4/ Tested with all inputs within 0.1 V of VDDor ground, no load. 5/ All transitions are measured at a 1.5 V level except tDISor tENA. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ST
45、ANDARD MICROCIRCUIT DRAWING SIZE A 5962-88739 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 8 DSCC FORM 2234 APR 97 Device types All Case outline Q Terminal number Terminal symbol Terminal number Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 P10
46、P9 P8CLK P TRIM TRIL P7P6P5P4P3P2P1P0X0X1X2X3X4X521 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 X6X7CLK X CLK Y RND Y0Y1Y2Y3VDDY4GND Y5Y6Y7P15P14P13P12P11Device types All Case outline X Terminal number Terminal symbol Terminal number Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1
47、6 17 18 19 20 21 22 P10P9 P8CLK P TRIM NC TRIL P7P6P5P4P3P2P1P0X0NC X1X2X3X4X523 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 X6X7CLK X CLK Y RND NC Y0Y1Y2Y3VDDY4GND Y5Y6Y7NC P15P14P13P12P11FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking p
48、ermitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88739 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 9 DSCC FORM 2234 APR 97 Device types 01, 02, 05, and 06 Device types 01, 02, 05, and 06 FIGURE 2. Input/output data format. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88739 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 10 DSCC FORM 2234 APR 97 Device types 03, 04, 07, and 08 Device types 03, 04,
