1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add vendor CAGE 01295. Add outline letter 2. Make changes to 1.3, table I, and figure 1. 92-10-29 M. A. FRYE B Sheet 8. TABLE I. The conditions header column, delete “V+ = +15 V”, “V- = -15 V” and substitute “V+ = +5 V” and “V- = 0 V”. Changes in
2、 accordance with N.O.R. 5962-R181-94. 94-05-06 M. A. FRYE C Sheet 7. TABLE I. Input offset voltage test. Device type 01. Group A subgroup 3, under maximum limit column, delete “450 V” and substitute “900 V”. Device type 02. Group A subgroup 3, under maximum limit column, delete “750 V” and substitut
3、e “1500 V”. Changes in accordance with N.O.R. 5962-R193-94. 94-07-08 M. A. FRYE D Drawing updated to reflect current requirements. Redrawn. - ro 02-03-13 R. MONNIN E Add case outline X and figure 1. Make changes to 1.2.2, 1.3, 3.2.1 and figure 2. - ro 07-08-08 R. HEBER F Make correction to Input off
4、set voltage test within +V = +5 V section under Table I. For subgroup 2, under the condition column, delete VCM= 0.1 V for the 900 V limit. For subgroup 2, under the condition column, add VCM= 0.1 V for the 450 V limit. - ro 10-12-13 C. SAFFLE THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLAC
5、ED. REV SHET REV SHET REV STATUS REV F F F F F F F F F F F F F OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY RICK OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND
6、 AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY D. H. JOHNSON APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, DUAL, PRECISION, OPERATIONAL AMPLIFIER, MONOLITHIC SILICON DRAWING APPROVAL DATE 89-04-12 AMSC N/A REVISION LEVEL F SIZE A CAGE CODE 67268 5962-88760 SHEET 1 OF 13 DSCC FORM 2233 APR 97
7、5962-E043-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88760 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes dev
8、ice requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-88760 01 G A Drawing number Device type (see 1.2.1) Case outline(see 1.2.2)
9、Lead finish(see 1.2.3)1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 LT1013A Dual precision operational amplifiers 02 LT1013 Dual precision operational amplifiers 1.2.2 Case outline(s). The case outline(s) are as desi
10、gnated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style G MACY1-X8 8 Can P GDIP1-T8 or CDIP2-T8 8 Dual-in-line X See figure 1 8 Can 2 CQCC1-N20 20 Square leadless chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A
11、. 1.3 Absolute maximum ratings. Positive supply voltage (+V) . +22 V dc Negative supply voltage (-V) . -22 V dc Power dissipation (PD) . 500 mW 1/ Differential input voltage . 30 V dc Input voltage . Supply voltage Output short circuit duration Indefinite Junction temperature (TJ) . +150C Storage te
12、mperature range . -65C to +150C Lead temperature: Cases G, P and X (soldering, 10 seconds) . +300C Case 2 (soldering, 60 seconds) . +260C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA): Cases G and X +150C/W Case P +110C/W Case 2 . +65C/W _
13、1/ Must withstand the added PDdue to short circuit test; e.g., IOS. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88760 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 3 DSCC FORM 223
14、4 APR 97 1.4 Recommended operating conditions. Positive supply voltage (+V) . +15 V dc Negative supply voltage (-V) . -15 V dc Common mode voltage (VCM) 0 V dc Ambient operating temperature range (TA) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The f
15、ollowing specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturi
16、ng, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microc
17、ircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this dra
18、wing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance
19、 with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535
20、may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall n
21、ot affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design
22、, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical
23、performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specifie
24、d in table II. The electrical tests for each subgroup are described in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88760 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 4 D
25、SCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA+125C unless otherwise specified Group A subgroups Device type Limits 1/ Unit Min Max Unless otherwise specified, +V = +15 V, -V = -15 V, VCM= 0 V Input offset voltage VIO1 01 150 V 2,3 300 1 02 300 2
26、,3 550 Input offset current IIO1 01 0.8 nA 2,3 2.5 1 02 1.5 2,3 5 Input bias current IIB1 01 20 nA 2,3 30 1 02 30 2,3 45 Input voltage range IVR 2/ 1 01 13.5 V 2,3 13.0 1 02 13.5 2,3 13.0 Average temperature coefficient of offset voltage VIO/ 3/ 4,5,6 01 2.0 V/C T 02 2.5 Common mode rejection ratio
27、CMRR VCM= +13.5 V, -15.0 V 4 01 100 dB VCM= +13.0 V, -14.9 V 5,6 97 VCM= +13.5 V, -15.0 V 4 02 97 VCM= +13.0 V, -14.9 V 5,6 94 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88
28、760 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA+125C unless otherwise specified Group A subgroups Device type Limits 1/ Unit Min Max Unless otherwise specified
29、, +V = +15 V, -V = -15 V, VCM= 0 V - continued Power supply rejection ratio PSRR +V = +2 V to +18 V, 1 01 103 dB -V = -2 V to -18 V 2,3 100 1 02 1002,3 97Output voltage swing VOSRL 2 k 4 01 13 V 5,6 12 4 02 12.5 5,6 11.5 Large signal voltage gain AVORL 2 k, VO= 10 V 4 01 1.5 V/V 5,6 0.5 4 02 1.25,6
30、0.25Power supply current ISYNo load, each amplifier 1 01 0.5 mA 2,3 0.61 02 0.552,3 0.7 Power dissipation PDNo load, each amplifier 4/ 1 01 15 mW 2,3 181 02 16.52,3 21 Channel separation CS RL= 2 k, TA= +25C 3/ 7 All 123 dB Output short circuit current -IOSTA= +25C 3/ 1 All -60 mA +IOS60See footnote
31、s at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88760 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characte
32、ristics Continued. Test Symbol Conditions -55C TA+125C unless otherwise specified Group A subgroups Device type Limits 1/ Unit Min Max Unless otherwise specified, +V = +15 V, -V = -15 V, VCM= 0 V - continued Input resistance, differential mode RINTA= +25C 3/ 1 01 100 M 02 70 Slew rate +SR Rising edg
33、e, VOUT= 5 V, TA= +25C, RL= 10 k, AV= 1, measured from -4 V to +4 V 7 All 0.2 V/s -SR Falling edge,VOUT= 5 V, TA= +25C, RL= 10 k, AV= 1, measured from +4 V to -4 V 0.2 Input offset voltage match VIOGuaranteed by VIOlimits 1 01 300 V 2,3 600 1 02 600 2,3 1100 See footnotes at end of table. Provided b
34、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88760 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbo
35、l Conditions -55C TA+125C unless otherwise specified Group A subgroups Device type Limits 1/ Unit Min Max Unless otherwise specified, +V = +5 V, -V = 0 V, VCM= 0 V, VOUT= 1.4 V Input offset voltage VIO1 01 250 V 2 900 VCM= 0.1 V 2 450 3 900 1 02 450 2 1500 VCM= 0.1 V 2 750 3 1500 Input offset curren
36、t IIO1 01 1.3 nA 2,3 6.01 02 2.0 2,3 10Input bias current IIB1 01 35 nA 2,3 80 1 0250 2,3 120 Input voltage range +IVR TA= +25C 2/ 1 All 3.5 V -IVR 0 Output voltage swing VOSNo load, output low 4 All 25 mV No load, output high 4 V Output low, ISINK= 1 mA 350 mV RL= 600 , output low 10 RL= 600 , outp
37、ut high 3.4 V RL= 600 , output low 5,6 01 15 mV 0218 RL= 600 , output high 01 3.2 V 023.1 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88760 DLA LAND AND MARITIME COLUMBUS, O
38、HIO 43218-3990 REVISION LEVEL F SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA+125C unless otherwise specified Group A subgroups Device type Limits 1/ Unit Min Max Unless otherwise specified, +V = +5 V, -V = 0 V, VCM= 0 V, VOUT
39、= 1.4 V - continued Power supply current ISYPer amplifier 1 01 0.45 mA 2,3 0.551 02 0.502,3 0.65 1/ The limiting terms “min” (minimum) and “max” (maximum) shall be considered to apply to magnitudes only. Negative current shall be defined as conventional current flow out of a device terminal. 2/ IVR
40、is guaranteed by CMRR test. 3/ If not tested, shall be guaranteed to the limits specified in table I herein. 4/ Power dissipation is guaranteed by the power supply current limits. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed
41、 in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C”
42、shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate o
43、f compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturers product
44、 meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification
45、 of change to DLA Land and Maritime -VA shall be required for any change that affects this drawing. 3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritime s agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentati
46、on. Offshore documentation shall be made available onshore at the option of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88760 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F
47、 SHEET 9 DSCC FORM 2234 APR 97 FIGURE 1. Case outline X. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88760 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 10 DSCC FORM 2234 APR 97 S
48、ymbol Dimensions Notes Inches Millimeters Min Max Min Max A .165 .185 4.19 4.70 b1 .016 .021 .41 .53 2 b2 .016 .024 .41 .61 D .335 .370 8.51 9.40D1 .305 .335 7.75 8.51 D2 .110 .160 2.79 4.06e .230 BSC 5.84 BSC F - .040 - 1.02 K .028 .034 .71 .86 K1 .027 .045 .69 1.14 3 L .500 .750 12.70 19.05 2 L1 - .050 - 1.27 2 Q .010 .045 .25 1.14 45 45 4 Note 1, 5, 6 NOTES: 1/ The U.S. government preferred system of m
