1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Drawing updated to reflect current requirements. -ro 01-06-19 R. MONNIN B Update drawing as part of 5 year review. -rrp 06-03-16 R. MONNIN C Update to reflect latest changes in format and requirements. -rrp 12-10-25 C. SAFFLE THE ORIGINAL FIRST S
2、HEET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY RICK OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE F
3、OR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY CHARLES E. BESORE APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, GENERAL PURPOSE OPERATIONAL AMPLIFIER, MONOLITHIC SILICON DRAWING APPROVAL DATE 89-09-28 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-89589 SHEE
4、T 1 OF 9 DSCC FORM 2233 APR 97 5962-E026-13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89589 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Sc
5、ope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-89589 01 C A Drawing number Device type (see
6、1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 LM107 Operational amplifier 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as fo
7、llows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line G MACY1-X8 8 Can P GDIP1-T8 or CDIP2-T8 8 Dual-in-line 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Positive supply voltage
8、(+VS) +22 V dc Negative supply voltage (VS) -22 V dc Differential input voltage 30 V dc Input voltage (VIN) . 15 V dc 1/ Output short circuit duration Indefinite Storage temperature range . -65C to +150C Lead temperature (soldering, 10 seconds) +260C Junction temperature (TJ) . +150C Power dissipati
9、on (PD) 500 mW 2/ Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA): Case C 85C/W (still air-board mount) 65C/W (400 LFPM air flow-board mount) Case G 180C/W (still air-flush mount) 75C/W (400 LFPM air flow-flush mount) Case P . 100C/W (still a
10、ir-board mount) 80C/W (400 LFPM air flow-board mount) 1/ For supply voltage less than 15 V, the absolute maximum input voltage is equal to the supply voltage. 2/ Must withstand the added PDdue to short circuit test, eg., IOS. Provided by IHSNot for ResaleNo reproduction or networking permitted witho
11、ut license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89589 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.4 Recommended operating conditions. Positive supply voltage range (+VS) +22 V dc Negative supply voltage range (-VS) . 22 V dc Ambi
12、ent operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these docum
13、ents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Comp
14、onent Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbin
15、s Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
16、 specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer L
17、isting (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML
18、flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with
19、MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outline. The case outline shall be in accordance with
20、 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating
21、 temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked w
22、ith the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89589 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C
23、SHEET 4 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Input offset voltage VIOVCM= 15 V 1 01 2 mV 2,3 3 VS= 5 V 1 2 2,3 3 Input offset current IIOVCM= 15 V, R
24、S= 50 k 1 01 10 nA 2,3 20 RS= 50 k 1 10 2,3 20 VS= 5 V, RS= 50 k 1 10 2,3 20 Input bias current IIBVCM= 15 V, RS= 50 k 1 01 75 nA 2,3 100 RS= 50 k 1 75 2,3 100 VS= 5 V, RS= 50 k 1 75 2,3 100 Supply current IS1 01 3 mA 2 2.5 3 3.5 Short circuit current IOS1 01 7 45 mA 2 5 45 3 7 50 See footnotes at e
25、nd of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89589 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristic
26、s Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Supply voltage rejection ratio +PSRR +VS= 20 V to 5 V 1,2,3 01 80 dB -PSRR -VS= -20 V to 5 V 80 Common mode rejection ratio CMRR -15 V VCM +15 V 1,2,3 01 80 dB Input volt
27、age range VIN1,2,3 01 15 V Input resistance 2/ RINTA= +25C 1 01 1.5 M Large signal voltage gain -AVSVS= 15 V, RL= 10 k, 1 01 50 V/mV VOUT= 0 V to 12 V 2,3 25 +AVSVS= 15 V, RL= 10 k, 1 50 VOUT= 0 V to 12 V 2,3 25 -AVSVS= 15 V, RL= 2 k, 1 50 VOUT= 0 V to 10 V 2,3 25 +AVSVS= 15 V, RL= 2 k, 1 50 VOUT= 0
28、 V to 10 V 2,3 25 Output voltage swing +VOPVS= 15 V, RL= 10 k 4,5,6 01 12 V/mV VS= 15 V, RL= 2 k 10 RL= 10 k 16 RL= 2 k 15 -VOPVS= 15 V, RL= 10 k -12 VS= 15 V, RL= 2 k -10 RL= 10 k -16 RL= 2 k -15 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted wit
29、hout license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89589 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group
30、 A subgroups Device type Limits Unit Min Max Slew rate SR VIN= -5 V to +5 V and VIN= +5 V to 5 V, TA= +25C 4 01 0.2 V/s Gain bandwidth GBW VIN= 50 mV rms, f = 20 kHz, RL= 2 k, TA= +25C 4 01 250 kHz 1/ Unless otherwise specified, VS= 20 V, VCM= 0 V, RS= 0 . 2/ If not tested, shall be guaranteed to th
31、e limits specified in table I herein. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-
32、PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Mar
33、itime -VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provi
34、ded with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be required for any change that affects this drawing. 3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritimes agent, and the acquirin
35、g activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MI
36、CROCIRCUIT DRAWING SIZE A 5962-89589 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Device type 01 Case outlines C G and P Terminal number Terminal symbol 1 NC NC 2 NC INPUT 3 NC INPUT 4 INPUT -VS5 INPUT NC 6 -VSOUTPUT 7 NC +VS8 NC NC 9 NC - 10 OUTPUT
37、- 11 +VS- 12 NC - 13 NC - 14 NC - NC = No connection FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89589 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEE
38、T 8 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality con
39、formance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring
40、activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II he
41、rein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-883 including groups A, B, C, and D inspections. The following ad
42、ditional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 7, 8, 9, 10, and 11 in table I, method 5005 of MIL-STD-883 shall be omitted. 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II
43、 herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circui
44、t shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TA= +125C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. Provided by IHSNot for ResaleNo reprodu
45、ction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89589 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 9 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance wit
46、h MIL-STD-883, method 5005, table I) Interim electrical parameters (method 5004) 1 Final electrical test parameters (method 5004) 1*, 2, 3 Group A test requirements (method 5005) 1, 2, 3, 4, 5, 6 Groups C and D end-point electrical parameters (method 5005) 1, 2, 3 * PDA applies to subgroup 1. 5. PAC
47、KAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and lo
48、gistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-prepared specification or drawing. 6.3 Configuration control of SMDs. All proposed changes to existing SMDs will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engi
