1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Technical changes in table I. Editorial changes throughout. 90-08-27 W. Heckman B Added Rochester as source of supply Vendor cage 3V146. Updated boilerplate and made editorial changes throughout. LTG 01-01-04 Thomas M. Hess C Made editorial chang
2、e to table I, sheet 5 on the VILtest in the max column. Updated bulletin page. - LTG 01-12-13 Thomas M. Hess D Correct tCLLHmaximum limit in table I. Update boilerplate to MIL-PRF-38535 requirements. - CFS 04-05-04 Thomas M. Hess E Update boilerplate to current MIL-PRF-38535 requirements. - CFS 09-0
3、5-05 Thomas M. Hess REV SHET REV E E E E E E E E E E E E E SHEET 15 16 17 18 19 20 21 22 23 24 25 26 27 REV STATUS REV E E E E E E E E E E E E E E OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Christopher A. Rauch DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING C
4、HECKED BY Charles Reusing COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY William K. Heckman MICROCIRCUIT, DIGITAL, NMOS, 16-BIT AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 89-09-14 MICROCONTROLLER, MONOLITHIC SILI
5、CON AMSC N/A REVISION LEVEL E SIZE A CAGE CODE 67268 5962-89596 SHEET 1 OF 27 DSCC FORM 2233 APR 97 5962-E291-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89596 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS,
6、OHIO 43218-3990 REVISION LEVEL E SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as show
7、n in the following example: 5962-89596 01 Z X Drawing number Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Frequency Circuit function 01 8097BH 12 MHz 16-bit microcon
8、troller 1.2.2 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style Y See figure 1 68 Leaded chip carrier with unformed leads Z CMGA3-P68 68 Pin grid array package 1.2.3 Lead finish. The lead finish is as spec
9、ified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Voltage on any pin with respect to VSSor ANGND (except EA) . -0.3 V dc to +7.0 V dc Voltage from EA to VSSor ANGND -0.3 V dc to +13.0 V dc Storage temperature range . -65C to +150C Maximum power dissipation (PD). 1.5 W Thermal resista
10、nce, junction-to-case (JC): Case Y 9C/W 1/ Case Z See MIL-STD-1835 Junction temperature (TJ) +175C Lead temperature (soldering, 5 seconds) +300C 1.4 Recommended operating conditions. Digital supply voltage range (VCC) . 4.5 V dc to 5.5 V dc Analog supply voltage range (VREF). 4.5 V dc to 5.5 V dc Po
11、wer down supply voltage range (VPD) 4.5 V dc to 5.5 V dc Oscillator frequency range (fOSC) . 6 MHz to 12 MHz Case operating temperature range (TC) -55C to +125C 2/ _ 1/ When a thermal resistance value is included in MIL-STD-1835, it shall supersede that value herein. 2/ Case temperatures are instant
12、 on. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89596 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specif
13、ication, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-
14、38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit
15、Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of
16、a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual i
17、tem requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted trans
18、itional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requireme
19、nts herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. This drawing has been
20、modified to allow the manufacturer to use the alternate die/fabrication requirements of paragraph A.3.2.2 of MIL-PRF-38535 or other alternative approved by the Qualifying Activity. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specif
21、ied in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be as specified on figure 1 or in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Functional block diagram. The functional block diagr
22、am shall be as specified on figure 3. 3.2.4 Instruction set summary. The instruction set summary shall be as specified on figure 4. 3.2.5 Timing waveforms . The timing waveforms shall be as specified on figure 5. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr
23、om IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89596 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 4 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specifie
24、d in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance w
25、ith MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962
26、-“ on the device. 3.5.1 Certification/compliance mark. The compliance mark for device class M shall be a “C” as required in MIL-PRF-38535, Appendix A. For class Q product built in accordance with A.3.2.2 of MIL-PRF-38535, or as modified in the manufacturers Quality Management (QM) Plan, the “QD” cer
27、tification mark shall be used in place of the “QML” or “Q” certification mark. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.7 herein). The certificate of compliance submit
28、ted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be
29、provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing. 3.9 Verification and review. DSCC, DSCCs agent, and the acquiring activity retain the option to review the manu
30、facturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89596 DEFENSE SU
31、PPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits Test Symbol Conditions 1/ -55C TC +125C VCC= VPD= 5 V 10% VSS= ANGND = 0 V fOSC= 6.0 to 12 MHz unless otherwise specified Group A subgroups Device typ
32、e Min Max Unit Supply current ICCAll outputs disconnected. 2/ 1, 2, 3 All 275 mA VPDsupply current IPDNormal operation and power down. 2/ 1, 2, 3 All 1 mA VREFsupply current IREF1, 2, 3 All 8 mA Input low voltage (except) RESET VIL1, 2, 3 All -0.3 0.8 V Input low voltage, RESET VIL11, 2, 3 All -0.3
33、0.7 V Input high voltage (except RESET, NMI and XTAL1) VIH1, 2, 3 All 2.0 VCC+0.5 V Input high voltage RESET rising VIH11, 2, 3 All 2.4 VCC+0.5 V Input high voltage, RESET falling hysteresis VIH21, 2, 3 All 2.1 VCC+0.5 V Input high voltage, NMI, XTAL1 VIH32/ 1, 2, 3 All 2.2 VCC+0.5 V Input leakage c
34、urrent to each pin of HSI, Port 3, Port 4 and P2.1 ILIVIN= 0 to VCC2/ 1, 2, 3 All 10 A DC input leakage current to each pin of Port 0 ILI1VIN= 0 to VCC2/ 1, 2, 3 All 3 A Input high current to EA IIHVIH= 2.4 V 2/ 1, 2, 3 All 100 A Input low current to Port 1, and P2.6, P2.7 IILVIL= 0.45 V 2/ 1, 2, 3
35、All -125 A Input low current to RESET IIL1VIL= 0.45 V 2/ 1, 2, 3 All -0.25 -2 mA Input low current P2.2, P2.3, P2.4, READY, BUSWIDTH IIL2VIL= 0.45 V 2/ 1, 2, 3 All -50 A See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-S
36、TANDARD MICROCIRCUIT DRAWING SIZE A 5962-89596 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Conditions 1/ -55C TC +125C VCC= VPD= 5 V 10% VSS= ANGND = 0 V fOSC=
37、6.0 to 12 MHz unless otherwise specified Group A subgroups Device type Min Max Unit Output low voltage on quasi-bidirectional port pins and Port 3, Port 4 when used as ports VOLIOL= 0.8 mA 2/ 3/ 1, 2, 3 All 0.45 V Output low voltage on quasi-bidirectional port pins and Port 3, Port 4 when used as po
38、rts VOL1IOL= 2.0 mA 2/ 3/ 4/ 5/ 1, 2, 3 All 0.75 V Output low voltage on standard output pins, RESET and Bus/control pins VOL2IOL= 2.0 mA 2/ 3/ 4/ 5/ 6/ 1, 2, 3 All 0.45 V Output high voltage on quasi-bidirectional pins VOHIOH= -20 A 2/ 3/ 1, 2, 3 All 2.4 V Output high voltage on standard output pin
39、s and Bus/control pins VOH1IOH= -200 A 2/ 3/ 1, 2, 3 All 2.4 V Output high current on RESET IOH3VOH= 2.4 V 2/ 1, 2, 3 All -50 A Pin capacitance CSf = 1.0 Mhz See 4.3.1c 2/ 4 All 10 pF Functional tests See 4.3.1d 2/ 7, 8 All See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction
40、or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89596 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Conditions 1/ -
41、55C TC +125C VCC= VPD= 5 V 10% VSS= ANGND = 0 V fOSC= 6.0 to 12 MHz unless otherwise specified Group A subgroups Device type Min Max Unit READY hold after CLKOUT edge tCLYX9,10, 11 All 0 ns End of ALE/ADV to READY valid tLLYV9,10, 11 All 2tOSC-70 ns End of ALE/ADV to READY high tLLYH9,10, 11 All 2tO
42、SC+40 4tOSC-80 ns Non-READY time tYLYH9,10, 11 All 1000 ns Address valid to input data valid 7/ tAVDV9,10, 11 All 5tOSC-120 ns RD active to input data valid tRLDV9,10, 11 All 3tOSC-100 ns Data hold after RD inactive tRHDX9,10, 11 All 0 ns RD inactive to input data float tRHDZ9,10, 11 All 0 tOSC-25 n
43、s Address valid to BUSWIDTH valid 7/ tAVGVTiming requirements (system components must meet these specifications). See figure 5. fOSC= 10 MHz 9,10, 11 All 2tOSC-125 ns BUSWIDTH hold after ALE/ADV low tLLGX9,10, 11 All tOSC+40 ns ALE/ADV low to BUSWIDTH valid tLLGV9,10, 11 All tOSC-75 ns Oscillator fr
44、equency fOSC9,10, 11 All 6.0 12.0 MHz Oscillator period tOSCSee figure 5. 9,10, 11 All 83 166 ns See footnotes at end of table.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89596 DEFENSE SUPPLY CENTER COLUM
45、BUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Conditions 1/ -55C TC +125C VCC= VPD= 5 V 10% VSS= ANGND = 0 V fOSC= 6.0 to 12 MHz unless otherwise specified Group A subgroups Device type Min
46、 Max Unit XTAL1 rising edge to clockout rising edge tOHCH9,10, 11 All 0 120 ns CLKOUT period 8/ tCHCH9,10, 11 All 3tOSC3tOSCns CLKOUT high time tCHCL9,10, 11 All 3tOSC-35 3tOSC+10 ns CLKOUT low to ALE high tCLLH9,10, 11 All -30 +15 ns ALE/ADV low to CLKOUT high tLLCH9,10, 11 All tOSC -25 tOSC +45 ns
47、 ALE/ADV high time 9/ tLHLL9,10, 11 All tOSC -30 9/ tOSC +35 9/ ns Address setup to end of ALE/ADV 7/ tAVLL9,10, 11 All tOSC -50 ns RD or WR low to address float 10/ tRLAZSee figure 5 fOSC= 10 MHz 9,10, 11 All 25 ns End of ALE/ADV to RD or WR active tLLRL9,10, 11 All tOSC -40 ns Address hold after e
48、nd of ALE/ADV 10/ tLLAX9,10, 11 All tOSC -40 ns WR pulse width tWLWH9,10, 11 All 3tOSC -35 ns Output data valid to end of WR/WRL/WRH tQVWH9,10, 11 All 3tOSC -60 ns Output data hold after WR/WRL/WRH tWHQX9,10, 11 All tOSC -50 ns End of WR/WRL/WRH to ALE/ADV high tWHLH9,10, 11 All tOSC -75 ns See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89596 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEE
