1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Change footnotes in conditions for standby current drain tests. Footnote 1, table I, change input voltage limits. Add case outline U. 92-01-13 M. A. FRYE B Changes in accordance with N.O.R. 5962-R085-94. 94-03-07 M. A. FRYE C Drawing updated to r
2、eflect current requirements. - ro 01-04-19 R. MONNIN D Add a footnote to the case outline U, TO-257 package as specified under 1.2.2. and figure 1. - ro 05-01-26 R. MONNIN E Drawing updated to reflect current requirements. -rrp 11-04-13 C. SAFFLE THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REP
3、LACED. REV SHEET REV SHEET REV STATUS REV E E E E E E E E E E E E OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY JOSEPH A. KERBY DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS
4、AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY CHARLES E. BESORE APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, 8-VOLT POSITIVE REGULATOR FIXED, MONOLITHIC SILICON DRAWING APPROVAL DATE 89-08-18 AMSC N/A REVISION LEVEL E SIZE A CAGE CODE 67268 5962-89628 SHEET 1 OF 12 DSCC FORM 2233 APR 97
5、5962-E306-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89628 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes dev
6、ice requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-89628 01 U A Drawing number Device type (see 1.2.1) Case outline (see 1.2.2)
7、 Lead finish (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 7808A Positive regulator, fixed 8-volt 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline lette
8、r Descriptive designator Terminals Package style U 1/ See figure 1 3 TO-257 Single row flange mount with isolated tab, glass sealed X See figure 1 3 TO-39 Can Y See figure 1 2 TO-3 Flange mount Z MBFM4-P2 2 TO-66 Flange mount 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appen
9、dix A. 1.3 Absolute maximum ratings. Input voltage: Operating or input shorted to ground . 35 V dc Transient 50 V dc 2/ Storage temperature range . -65C to +150C Lead temperature (soldering, 10 seconds) +300C Power dissipation (PD): TC= +25C: Cases U and Z . 15 W Case X . 2 W Case Y . 20 W TA= +25C:
10、 Cases U and Z . 3.0 W Case X . 1.0 W Case Y . 4.3 W _ 1/ For outline letter U, CAGE 34333 manufacturers the TO-257 package with ceramic seal. 2/ The 50-volt input rating refers to the ability of the regulator to withstand high line or transient conditions without damage. Since the regulators maximu
11、m current capability is reduced, the output may fall out of regulation at high input voltages under nominal loading. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89628 DLA LAND AND MARITIME COLUMBUS, OHIO
12、43218-3990 REVISION LEVEL E SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings continued. Junction temperature (TJ) +150C 3/ Thermal resistance, junction-to-case (JC): Case U . 4.2C/W Case X 15C/W Case Y 3C/W Case Z 6C/W Thermal resistance, junction-to-ambient (JA): Cases U and Z . 50C/W Cas
13、e X . 120C/W Case Y 35C/W 1.4 Recommended operating conditions. Input voltage range (VIN) . +11.0 V dc to +25 V dc Ambient operating temperature range (TA) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbo
14、oks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF
15、DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents a
16、re available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the tex
17、t of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 3/ The device is protected by thermal shutdown circuit which is designed to turn off the output transistor whenever the device junction t
18、emperature is in excess of +150C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89628 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item
19、requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufactu
20、rer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make
21、modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option i
22、s used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connec
23、tions shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The elec
24、trical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacture
25、rs PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN device
26、s built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a
27、 manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38
28、535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DLA Land and Maritime -
29、VA shall be required for any change that affects this drawing. 3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritime s agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be m
30、ade available onshore at the option of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89628 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 5 DSCC FORM 2234 APR 97 TABLE
31、I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output voltage VOUTTA= +25C 1 01 7.88 8.12 V VIN= 11.5 to 23 V 2/ 1,2,3 7.76 8.24 Line regulation 3/ 4/ VRLINEVIN= 10.5 to 25 V 1 01 40 mV 2
32、,3 60 VIN= 11 to 17 V 1 20 2,3 30 Load regulation 3/ VRLOADIO= 5.0 mA to 1.0 A 5/ 1 01 70 mV 2,3 100 IO= 250 mA to 750 mA 5/ 1 35 2,3 50 IO= 5.0 mA to 500 mA 6/ 1 35 2,3 50 Standby current drain ISCD1 01 6.0 mA 2,3 6.5 Standby current drain change with line ISCD(line) VIN= 11.5 V to 25 V 1,2,3 01 1.
33、0 mA Standby current drain change with load ISCDIO= 5.0 mA to 1.0 A 5/ 1,2,3 01 0.5 mA (load) IO= 5.0 mA to 500 mA 6/ 0.5 Dropout voltage VDOVOUT= 100 mV, 5/ IO= 1.0 A 1,2,3 01 2.5 V VOUT= 100 mV, 6/ IO= 500 mA 2.5 Peak output current IO(pk) TA= +25C 5/ 1 01 1.5 3.3 A TA= +25C 6/ 0.5 1.7 See footnot
34、es at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89628 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance charact
35、eristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Short circuit current 7/ IOSVIN= 35 V 5/ 1 01 1.2 A 2,3 2.8 VIN= 35 V 6/ 1 0.7 2,3 2.0 Ripple rejection 3/ VIN/ VIN= 10 V, fO= 120 Hz 4 01 62 dB VOUT5,6 8/ 60 Outp
36、ut noise voltage 8/ NOfO= 10 Hz to 100 kHz, TA= +25C 7 01 40 V / Vrms Long term stability 8/ VOUT/ t = 1,000 hours, 7 01 75 mV t TA= +25C 1/ Unless otherwise specified, VIN= 14 V and IO= 500 mA for cases U, Y, and Z. VIN= 14 V and IO= 100 mA for case X. Maximum test current for case X is 500 mA. 2/
37、For cases X: IO= 5 mA to 500 mA, P 2 W. For case Y: IO= 5 mA to 1.0 A, P 20 W. For cases U and Z: IO= 5 mA to 1.0 A, P 15 W. 3/ All measurements except output noise voltage and ripple rejection are made at constant junction temperature and with low duty cycle. 4/ Minimum load current for full line r
38、egulation is 5.0 mA. 5/ For cases Y and Z only. 6/ For case X only. 7/ Short circuit protection is only assured up to VIN= 35 V. 8/ If not tested, shall be guaranteed to the limits specified in table I herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from
39、IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89628 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 7 DSCC FORM 2234 APR 97 Case outline U Inches mm .005 0.13 .010 0.25 .020 0.51 Letter Inches Millimeters Min Max Min Max A .190 .200 4.83 5.08 A1 .035 .045 0.89 1.14 A2 .120
40、 BSC 3.05 BSC b .025 .035 0.64 0.89 D .645 .665 16.38 16.89 D1 .410 .430 10.41 10.92 D3 .000 .065 0.00 1.65 e .100 BSC 2.54 BSC E .410 .422 10.41 10.71 L .500 .750 12.70 19.05 O .527 .537 13.39 16.64 P .140 .150 3.56 3.81 NOTE: 1. The U.S. government preferred system of measurement is the metric SI
41、system. However, since this item was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. 2. For case outline U only, CAGE 34333, the ceramic seal that protrudes from the seating plane
42、 is not to be considered in overall package dimensions. The ceramic seal protrusion is considered uncontrolled within an area 30 mils from the seating plane. FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCU
43、IT DRAWING SIZE A 5962-89628 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 8 DSCC FORM 2234 APR 97 Case outline X Letter Inches Millimeters Notes Min Max Min Max A .165 .185 4.19 4.70 b .016 .019 0.41 0.48 2 b2 .016 .021 0.41 0.53 2 D .335 .370 8.51 9.40 D1 .305 .335 7.75 8.
44、51 e .200 T.P. 5.08 T.P. 4 e1 .100 T.P. 2.54 T.P. 4 F .050 1.27 j .029 .045 0.74 1.14 3 k .028 .034 0.71 0.86 L .500 12.70 L1 .050 1.27 L2 .250 6.35 45 T.P. 45 T.P. NOTES: 1. The U.S. government preferred system of measurement is the metric SI system. However, since this item was originally designed
45、 using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. 2. (All leads) b applies between the L1 and L2. b2 applies between the L2 and .500 inch (12.70 mm) from the reference plane. Diameter is uncontrolled
46、in L1 and beyond .500 inch (12.70 mm) from the reference plane. 3. Measured from the maximum diameter of the product. 4. Leads having a maximum diameter of .019 inch (0.48 mm) measured in gauging plane .054 inch (1.37 mm) + .001 inch (0.03 mm) - .000 inch (0.00 mm) below the base plane of the produc
47、t shall be within .007 inch (0.18 mm) of their true-position relative to a maximum width tab. 5. The product may be measured by direct methods or by gauge. FIGURE 1. Case outlines Continued Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MIC
48、ROCIRCUIT DRAWING SIZE A 5962-89628 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 9 DSCC FORM 2234 APR 97 Case outline Y Letter Inches Millimeters Notes Min Max Min Max A .250 .450 6.35 11.43 A1 1.177 1.197 29.90 30.40 b .038 .043 0.97 1.09 2, 6 D .875 22.22 e .655 .675 16.64 17.14 4 e1 .420 .440 10.67 11.16 4 e2 .205 .225 5.21 5.72 F .060 .135 1.52 3.43 L .312 .500 7.92 12.70 3 L1 .050 1.27 2, 3 P .151 .1
