1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with N.O.R. 5962-R035-93. 93-03-18 M. A. FRYE B Changes in accordance with N.O.R. 5962-R176-96. 94-01-03 M. A. FRYE C Drawing updated to reflect current requirements. -ro 01-04-11 R. MONNIN D Update drawing as part of 5 year
2、 review. -rrp 07-07-11 R. HEBER E Update to reflect latest changes in format and requirements. -rrp 12-12-04 C. SAFFLE THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV E E E E E E E E E E E OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY RIC
3、K C. OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY CHARLES E. BESORE APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, F
4、AST SETTLING, UNITY-GAIN STABLE, OPERATIONAL AMPLIFIER, MONOLITHIC SILICON DRAWING APPROVAL DATE 92-07-07 AMSC N/A REVISION LEVEL E SIZE A CAGE CODE 67268 5962-89641 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E115-13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license
5、from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89641 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with
6、 MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-89641 01 C A Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as
7、 follows: Device type Generic number Circuit function 01 AD841 Unity-gain stable, fast settling operational amplifier 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14
8、 Dual-in-line X See figure 1 12 Can 2 CQCC1-N20 20 Square leadless chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. 1/ 2/ Voltage between +VSand VSterminals 36 V dc Differential input voltage 6.0 V dc Voltage at either input
9、terminal +VSand VSPeak output current ( 10 % duty cycle) . 100 mA Power dissipation (PD): Case C 1.3 W 3/ Case X . 1.5 W 3/ Case 2 . 1.0 W 3/ Junction temperature (TJ) . +175C Storage temperature range . -65C to +150C Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-cas
10、e (JC): Cases C and X 30C/W Case 2 . 35C/W Thermal resistance, junction-to-case (JA): Case C 110C/W Case X . 100C/W Case 2 . 150C/W 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reli
11、ability. 2/ Unless otherwise specified, TA= +25C. 3/ Derate linearly above TA= +25C for case C at 8.7mw/C, case X at 10 mW/C and case 2 at 6.7 mW/C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89641 DLA L
12、AND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 3 DSCC FORM 2234 APR 97 1.4 Recommended operating conditions. Positive supply voltage range (+VS) +5 V dc to +15 V dc Negative supply voltage range (-VS) . -5 V dc to 15 V dc Common mode input voltage (VCM) 10 V dc Load resistance (RL
13、) . 500 Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of
14、 these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Ele
15、ctronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk
16、, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulati
17、ons unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Ma
18、nufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-3853
19、5. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in acco
20、rdance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outline. The case outline shall be in acc
21、ordance with 1.2.2 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over t
22、he full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without
23、license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89641 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 4 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA +125C VS= 15 V Group A subgroups Device type Limits 2
24、/ Unit unless otherwise specified Min Max Input offset voltage VIOVCM= 0 V 1 01 -2.0 +2.0 mV 2,3 -5.5 +5.5 Input bias current +IBVCM= 0 V 1 01 +8 A 2,3 +12 -IB1 +8 2,3 +12 Input offset current IIOVCM= 0 V 1 01 -0.4 +0.4 A 2,3 -0.6 +0.6 Common mode voltage range +VCM+VS= 5.0 V, -VS= -25 V VOUT= -10 V
25、 1,2,3 01 10 V -VCM+VS= 25 V, -VS= -5 V VOUT= 10 V -10 Large signal voltage gain +AVOLVOUT= 0 V and 10 V, 1 01 25 V/mV RL= 500 2,3 12 -AVOLVOUT= 0 V and -10 V, 1 25 RL= 500 2,3 12 Output current +IOUTVOUT= 0 V, TA= +25C 1 01 50 mA -IOUTVOUT= 0 V, TA= +25C -50 Output voltage swing +VOUTRL= 500 1,2,3
26、01 10 V -VOUT-10 Quiescent power supply current +ICCVOUT= 0 V, IOUT= 0 mA 1 01 +12 mA 2,3 +16 -ICC1 -12 2,3 -16 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89641 DLA LAND AN
27、D MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C VS= 15 V Group A subgroups Device type Limits 2/ Unit unless otherwise specified Min Max Power supply rejection ratio
28、 +PSRR +VS= 5.0 V to 18 V, 1 01 86 dB -VS= -15 V 2,3 80 -PSRR -VS= -5.0 V to 18 V 1 86 +VS= +15 V 2,3 80 Quiescent power 3/ consumption PCVOUT= 0 V, IOUT= 0 mA 1 01 360 mW 2,3 480 Common mode rejection ratio +CMRR VCM= 10 V, +VS= 5.0 V, 1 01 86 dB -VS= -25 V, VOUT= -10 V 2,3 80 -CMRR VCM= -10 V, +VS
29、= 25 V, 1 86 -VS= -5 V, VOUT= 10 V 2,3 80 Differential input 4/ resistance RINVCM= 0 V, TA= +25C 4 01 65 k Gain bandwidth 4/ product GBWP VOUT= 100 mV, f1= 100 kHz, f2= 10 MHz, RL= 500 , TA= +25C 4 01 23 MHz Full power 4/ 5/ bandwidth FPBW VPK= 10 V, RL= 500 , TA= +25C 4 01 3.1 MHz Closed loop stabl
30、e 4/ gain CLSG RL= 500 , CL 10 pF 4,5,6 01 1 V/V Slew rate 4/ +SR VOUT= -5.0 V to 5.0 V, measured from 10 % to 9 01 220 V/s 90 % point, RL= 500 , AV= -1 V/V, rising edge 10,11 140 -SR VOUT= 5.0 V to -5.0 V, measured from 90 % to 9 220 10 % point, RL= 500 , AV= -1 V/V, falling edge 10,11 140 See foot
31、notes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89641 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance char
32、acteristics Continued. Test Symbol Conditions 1/ -55C TA +125C VS= 15 V Group A subgroups Device type Limits 2/ Unit unless otherwise specified Min Max Rise time 4/ 6/ tRVOUT= 0 V to +200 mV, AV= +1, RL= 500 , 9,10,11 01 10 ns Fall time 4/ 6/ tFVOUT= 0 V to -200 mV, AV= +1, RL= 500 , 9,10,11 01 10 n
33、s Settling time 4/ tSAV= -1 V/V, RL= 500 , 10 V step at 0.1 % of the fixed value, TA= +25C 9 01 150 ns AV= -1 V/V, RL= 500 , 10 V step at 0.01 % of the fixed value, TA= +25C 200 Overshoot 4/ +OS VOUT= 0 V to +200 mV, AV= +1, RL= 500 , TA= +25C 9 01 40 % -OS VOUT= 0 V to -200 mV, AV= +1, RL= 500 , TA
34、= +25C 40 1/ Unless otherwise specified, for dc tests, RL= 100 k and VOUT= 0 V. 2/ The algebraic convention, whereby the most negative value is a minimum and the most positive is a maximum, is used in this table. Negative current shall be defined as conventional current flow out of device terminal.
35、3/ Quiescent power consumption is based on quiescent supply current test maximum with no load on outputs. 4/ If not tested, shall be guaranteed to the limits specified in table I herein. 5/ Full power bandwidth = SR / ( 2 x VPK). 6/ Rise and fall times measured between 10 percent and 90 percent poin
36、t. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89641 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 7 DSCC FORM 2234 APR 97 Case outline X Symbol Inches Millimeters Notes Min Max M
37、in Max A .148 .181 3.76 4.60 b .016 .019 0.41 0.48 1 b1 .016 .021 0.41 0.53 1 D .592 .615 15.04 15.62 D1 .545 .555 13.84 14.10 e .400 BSC 10.16 BSC 3 e1 .200 BSC 5.00 BSC 3 e2 .100 BSC 2.54 BSC 3 F - .040 - 1.02 k .026 .036 0.66 0.91 k1 .027 .037 0.68 0.94 2 L .375 - 9.50 - L1 - .050 - 1.27 1 Q .010
38、 .045 0.25 1.14 NOTES: 1. All leads b applies between L and L1. b1 applies between L1and .375 inch (9.52 mm) from the reference plane. 2. Measured from the maximum diameter of the product. 3. Leads having a maximum diameter .019 inch (0.48 mm) measured in gauging plane .054 inch (1.37 mm) + .001 inc
39、h (0.03 mm) - .000 inch (0.000 mm) below the base plane of the product are within .007 inch (0.18 mm) of their true position relative to the maximum width tab. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRC
40、UIT DRAWING SIZE A 5962-89641 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Case outlines C X 2 Terminal number Terminal symbol 1 NC NC NC 2 NC NC BALANCE 3 BALANCE BALANCE NC 4 -INPUT BALANCE NC 5 +INPUT -INPUT -INPUT 6 -VS+INPUT NC 7
41、NC NC +INPUT 8 NC NC NC 9 NC NC NC 10 OUTPUT -VS-VS11 +VSOUTPUT NC 12 BALANCE +VSNC 13 NC - NC 14 NC - NC 15 - - OUTPUT 16 - - NC 17 - - +VS18 - - NC 19 - - NC 20 - - BALANCE NC = No connection FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted witho
42、ut license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89641 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 9 DSCC FORM 2234 APR 97 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herei
43、n. In addition, the manufacturers PIN may also be marked. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certifica
44、tion/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is use
45、d. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of s
46、upply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this
47、drawing. 3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be required for any change that affects this drawing. 3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufactur
48、ers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883
