1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R209-92. 92-05-18 M. A. Frye B Redraw. Incorporate revision A NOR. Update to current requirements. - drw 09-03-02 Robert M. Heber THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHET REV SHET RE
2、V STATUS REV B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Joseph A. Kerby CHECKED BY Charles E. Besore DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil APPROVED BY Michael A. Frye STANDARD MICROCIRCUIT DRAWING THIS DRAWIN
3、G IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 91-11-04 MICROCIRCUIT, LINEAR, VIDEO A/D CONVERTER, 4-BIT, 25 MSPS, MONOLITHIC SILICON AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-89828 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E170-0
4、9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89828 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes devic
5、e requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-89828 01 E A Drawing number Device type (see 1.2.1) Case outline(see 1.2.2) Le
6、ad finish(see 1.2.3)1.2.1 Device type. The device type identifies the circuit function as follows: Device type Generic number Circuit function 01 TDC1044 Video A/D converter, 4-bit, 25 MSPS 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter De
7、scriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. 1/ Supply voltages: VCC(measured to DGND) . -0.5 V to +7.0 V VEE(measured to AGND) +0.5 V to -7.0 V AGN
8、D(measured to DGND) . -0.5 V to +0.5 V Inputs: CONV, NMINV, NLINV (measured to DGND). -0.5 V to +5.5 V VIN, VRT, VRB(measured to AGND) . +0.5 V to VEEVRT(measured to VRB) . -2.2 V to +2.2 V Outputs: Applied voltage (measured to DGND) 2/. -0.5 V to +5.5 V Applied current, externally forced 3/, 4/ -1.
9、0 mA to +6.0 mA Short circuit duration (single output in high state to GND) 1 second Storage temperature range -65C to +150C Junction temperature (TJ) +150C Lead temperature (soldering, 10 seconds) +300C Power dissipation (PD) . 1.6 W Thermal resistance, junction-to-case (JC). See MIL-STD-1835 _ 1/
10、Absolute maximum ratings are limiting values applied individually while all other parameters are within specified operating conditions. Functional operation under any of these conditions is not implied. 2/ Applied voltage must be current limited to specified range. 3/ Forcing voltage must be limited
11、 to specified range. 4/ Current is specified as conventional current flowing into the device. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89828 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REV
12、ISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.4 Recommended operating conditions. Positive supply voltage (VCC) (measured to DGND) . 4.5 V to 5.5 V Negative supply voltage (VEE) (measured to AGND) -4.9 V to -5.5 V Analog ground voltage (VAGND) (measured to DGND) -0.1 V to 0.1 V CONV pulse width, LOW
13、 (tPWL) (see figure 4) 17 ns min CONV pulse width, HIGH (tPWH) (see figure 4) 17 ns min Input voltage, logic LOW (VIL) 0.8 V max Input voltage, logic HIGH (VIH). 2.0 V min Output current, logic LOW (IOL) 2.0 mA max Output current, logic HIGH (IOH). -400 A min Most positive reference (VRT). -1.9 V to
14、 +0.1 V Most negative reference (VRB) . -2.1 V to -0.1 V Reference differential (VRT VRB) 0.2 V to 2.0 V Input voltage (VIN) VRBto VRTAmbient operating temperature range (TA) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, st
15、andards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification
16、for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies o
17、f these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cit
18、ed herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT D
19、RAWING SIZE A 5962-89828 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as spec
20、ified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved
21、 program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not
22、 affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-3853
23、5, appendix A and herein. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagra
24、m shall be as specified on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electric
25、al test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers P
26、IN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices bu
27、ilt in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a man
28、ufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and th
29、e requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that
30、 affects this drawing. 3.9 Verification and review. DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. Provided by IHSNot for
31、 ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89828 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions
32、-55C TA+125C 4.5 V VCC 5.5 V Group A subgroupsDevice type Limits Unit unless otherwise specified Min Max Positive supply current ICCVCC= 5.5 V 1/ 1, 2, 3 All 20 mA Negative supply current IEEVEE= -5.5 V 1/ 1, 3 All -65 mA 2 -35 Reference current IREFVRT= 0 V, VRB= -1 V 1, 2, 3 All 2 mA Total referen
33、ce resistance 2/ RREFVRT= 0 V, VRB= -1 V 1, 2, 3 All 500 Input equivalent resistance 2/ RINVRT= 0 V, VIN= VRB= -1 V 1, 2, 3 All 100 k Input capacitance 2/ CINVRT= 0 V, VRB= -1 V, see 4.3.1b 4, 5, 6 All 25 pF Input constant bias current ICBVEE= -5.5 V 1, 2, 3 All 50 A Input current, low IILCONV pin 1
34、, 2, 3 All -0.6 mA VCC= 5.5 V, VI= 0.4 V NMINV and NLINV pins -0.8 Input current, high IIHVCC= 5.5 V, VI= 2.4 V 1, 2, 3 All 50 A Input current, maximum input voltage IIVCC= 5.5 V, VI= 5.5 V 1, 2, 3 All 1.0 mA Output voltage, low VOLVCC= 4.5 V, IOL= 2.0 mA 1, 2, 3 All 0.5 V Output voltage, high VOHVC
35、C= 4.5 V, IOH= -400 A 1, 2, 3 All 2.4 V Short circuit output current IOSVCC= 5.5 V, one pin to ground, one second duration, output high 1, 2, 3 All -30 mA See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCI
36、RCUIT DRAWING SIZE A 5962-89828 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - continued. Test Symbol Conditions -55C TA+125C 4.5 V VCC 5.5 V Group A subgroupsDevice type Limits Unit unless oth
37、erwise specified Min Max Digital input capacitance 2/ CITA= 25C, f = 1 MHz, see 4.3.1b 4 All 15 pF Maximum conversion rate 2/ FSVCC= 5.0 V, VEE= -5.2 V 4, 5, 6 All 25 MSPS Sampling time offset 2/ tSTOVCC= 5.0 V, VEE= -5.5 V, see figure 4 9, 10, 11 All 15 ns Digital output delay tDVCC= 5.5 V, VEE= -4
38、.9 V, see figure 4 9, 10, 11 All 35 ns Digital output hold time 2/ tHOVCC= 5.5 V, VEE= -4.9 V, see figure 4 9, 10, 11 All 5 ns Linear error, integral independent ELIVRB= -1.0 V 4, 5, 6 All 1.6 % Linear error, differential ELDVRB= -1.0 V 4, 5, 6 All 1.6 % Code size CS VRT= 0 V, VRB= -1 V 1, 2, 3 All
39、75 125 % of nominal Offset error, top 2/ EOTVIN= VRT1, 2, 3 All +30 mV Offset error, bottom 2/ EOBVIN= VRB1, 2, 3 All +40 mV Offset error, temperature coefficient 2/ TCOVIN= VRB2, 3 All -20 +20 V/C Bandwidth, full power input 2/ BW 4, 5, 6 All 12.5 MHz Functional tests VCC= 4.5 V, VEE= -4.9 V, f = 1
40、 MHz, see 4.3.1c 7, 8 All 1/ Worst case, all digital inputs and outputs low. 2/ Guaranteed, if not tested, to the limits specified. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89828 DEFENSE SUPPLY CENTER
41、COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 Device type 01 Case outline E Terminal number Terminal symbol 1 AGND2 VIN3 NC 4 RT5 RB6 VEE7 NLINV 8 RM9 NMINV 10 VCC11 DGND12 D1(MSB) 13 D214 D315 D4(LSB) 16 CONV FIGURE 1. Terminal connections. Provided by IHSNot for
42、 ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89828 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 Output coding table (see note) Binary Offset twos complement Range True
43、Inverted True Inverted -1.00 V FS NMINV - 1 0 0 1 NLINV - 1 0 1 0 -0.000 V 0000 1111 1000 0111 -0.067 V 0001 1110 1001 0110 -0.133 V 0010 1101 1010 0101 -0.200 V 0011 1100 1011 0100 -0.267 V 0100 1011 1100 0011 -0.333 V 0101 1010 1101 0010 -0.400 V 0110 1001 1110 0001 -0.467 V 0111 1000 1111 0000 -0
44、.533 V 1000 0111 0000 1111 -0.600 V 1001 0110 0001 1110 -0.667 V 1010 0101 0010 1101 -0.733 V 1011 0100 0011 1100 -0.800 V 1100 0011 0100 1011 -0.867 V 1101 0010 0101 1010 -0.933 V 1110 0001 0110 1001 -1.000 V 1111 0000 0111 1000 NOTE: Input voltages are at code centers. FIGURE 2. Truth table. Provi
45、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89828 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 FIGURE 3. Logic diagram. Provided by IHSNot for ResaleN
46、o reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89828 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 10 DSCC FORM 2234 APR 97 FIGURE 4. Timing diagram and I/O equivalent circuits. Provided by IHSNot for Re
47、saleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89828 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 11 DSCC FORM 2234 APR 97 FIGURE 4. Timing diagram and I/O equivalent circuits - continued. Provided
48、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89828 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 12 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening s
