1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R037-92. 91-11-12 M. A. Frye B Incorporate revision A, NOR. Update drawing to current requirements. Editorial changes throughout. drw 07-05-02 Robert M. Heber THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN R
2、EPLACED. REV SHET REV SHET REV STATUS REV B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 PMIC N/A PREPARED BY Joseph A. Kerby DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Charles E. Besore COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE
3、BY ALL DEPARTMENTS APPROVED BY Monica L. Poelking MICROCIRCUIT, LINEAR, QUAD NAND RELAY AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 90-04-05 DRIVERS, MONOLITHIC SILICON AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-89867 SHEET 1 OF 8 DSCC FORM 2233 APR 97 5962-E387-07 Pro
4、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89867 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device req
5、uirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-89867 01 C A Drawing number Device type (see 1.2.1) Case outline(see 1.2.2) Lead fi
6、nish(see 1.2.3)1.2.1 Device type. The device type identifies the circuit function as follows: Device type Generic number Circuit function 01 UH-507 Quad NAND driver, high-output voltage and current 1.2.2 Case outline. The case outline is as designated in MIL-STD-1835 as follows: Outline letter Descr
7、iptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage (VCC) 7.0 V dc Input voltage (VIN) 5.5 V dc Output off-state voltage (VS) 100 V dc Output o
8、n-state sink current 500 mA Storage temperature range -65C to +150C Lead temperature (soldering, 10 seconds) +300C Junction temperature (TJ) +150C Thermal resistance, junction-to-case (JC). See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA) 90C/W 1.4 Recommended operating conditions. Supp
9、ly voltage range (VCC) 4.5 V to 5.5 V Current into any output (on-state) 250 mA maximum Ambient operating temperature range . -55C to +125C Minimum high level input voltage VIN(1). 2.0 V Maximum low level input voltage VIN(0) . 0.8 V Provided by IHSNot for ResaleNo reproduction or networking permitt
10、ed without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89867 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standar
11、ds, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
12、DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of the
13、se documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawin
14、g and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance wi
15、th MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may
16、 be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not
17、affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, c
18、onstruction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections and logic diagram. The terminal connections and logic diagram shall be as specified on figure
19、1. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the
20、subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For package
21、s where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535
22、, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT D
23、RAWING SIZE A 5962-89867 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Input cu
24、rrent, high IIN(1)VCC= 5.5 V, driven input = 2.4 V, other input = 0 V 1, 2,3 All 40 A VCC= 5.5 V, driven input = 5.5 V, other input = 0 V 1000 Input current, low IIN(0)VCC= 5.5 V, driven input = 0.4 V, other input = 4.5 V 1, 2, 3 All -800 A Output reverse current IOFFVCC= 4.5 V, driven input = 2.4 V
25、, VO= 100 V, other input = 4.5 V 1, 2, 3 All 100 A Output voltage, low VONVCC= 4.5 V, output = 150 mA, all inputs = 2.0 V 1, 3 All 0.5 V 2 0.6 VCC= 4.5 V, output = 250 mA, all inputs = 2.0 V 1, 3 0.7 2 0.8 Supply current, high level (all drivers) ICC(1)VCC= 5.5 V All inputs = 0 V 1 All 30.0 mA 2, 3
26、1/ 40.0 Supply current, low level (all drivers) ICC(0)All inputs = 5.0 V 1 106.0 2, 3 1/ 135.0 Propagation delay, turn-on time tpd0VCC= 5.0 V, VS= 100 V, CL= 15 pF, RL= 670 9, 10, 11 All 500 ns Propagation delay, turn-off time tpd1See figure 2 750 Input voltage, high VIN(1)VCC= 4.5 V 1, 2, 3 All 2.0
27、 V Input voltage, low VIN(0)0.8 Strobe input current IIN(0)VCC= 5.5 V other input = 4.5 V, driven input = 0.4 V 1, 2, 3 All -1.6 mA IIN(1)other input = 0 V, driven input = 2.4 V 1, 2, 3 All 100 A other input = 0 V, driven input = 5.5 V 1000 Diode leakage current IRVCC= 5.0 V, driven input = 5.0 V, o
28、ther input = 5.0 V, output = open, cathode = 100 V 1, 2, 3 All 200 A Diode forward voltage VFVCC= 5.0 V, driven input = 0 V, other input = 0 V, diode current = 200 mA 1, 2, 3 All 1.75 V 1/ Guaranteed, if not tested to the limits specified. Provided by IHSNot for ResaleNo reproduction or networking p
29、ermitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89867 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 FIGURE 1. Terminal connections and logic diagram. Provided by IHSNot for ResaleNo reproduction or networking p
30、ermitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89867 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 Input pulse characteristics VIN(0)= 0 V, tf 7.0 ns, tp= 1.0 s VIN(1)= 3.5 V, tr 14 ns, PRR = 500 kHz FIGURE 2.
31、 Waveforms, switching circuit, and input pulse characteristics. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89867 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FOR
32、M 2234 APR 97 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply s
33、hall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing
34、. 3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing. 3.9 Verification and review. DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshor
35、e documentation shall be made available onshore at the option of the reviewer. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and s
36、hall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and s
37、hall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical
38、 test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-STD-883, method 5005, tabl
39、e I) Interim electrical parameters (method 5004) - - - Final electrical test parameters (method 5004) 1*, 2, 3, 9 Group A test requirements (method 5005) 1, 2, 3, 9, 10*,11* Groups C and D end-point electrical parameters (method 5005) 1, 2, 3 * PDA applies to subgroup 1. * Subgroups 10 and 11, if no
40、t tested, shall be guaranteed to the specified limits in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89867 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC F
41、ORM 2234 APR 97 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II h
42、erein. b. Subgroups 4, 5, 6, 7, and 8 in table I, method 5005 of MIL-STD-883 shall be omitted. 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C,
43、or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with t
44、he intent specified in method 1005 of MIL-STD-883. (2) TA= +125C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. 6. NOTES 6.1 In
45、tended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor
46、-prepared specification or drawing. 6.3 Configuration control of SMDs. All proposed changes to existing SMDs will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.4 Record of users. Militar
47、y and industrial users shall inform Defense Supply Center Columbus (DSCC) when a system application requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings c
48、overing microelectronics devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544. 6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43218-3990, or telephone (614) 692-0547. 6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MIL-HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DSCC-VA. Provided by IHSNot for ResaleNo reproduction or networking permitted
