1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add notes to figure 4, switching waveforms and test circuit. Make corrections on table II, electrical test requirements. Update boilerplate to MIL-PRF-38535 requirements. Editorial changes throughout. - LTG 05-12-15 Thomas M. Hess B Update the bo
2、ilerplate paragraphs to the current MIL-PRF-38535 requirements. - jak 11-09-19 Thomas M. Hess REV SHEET REV SHEET REV STATUS REV B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Marcia B. Kelleher DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.l
3、andandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED BY Thomas J. Ricciuti THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Michael A. Frye MICROCIRCUIT, DIGITAL, HIGH SPEED CMOS, 12-STAGE RIPPLE-CARRY BINARY COUNTER, TTL COMPATIBLE INPUTS, MONOLITHIC SILICON AND AGENCIES OF
4、 THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 91-07-17 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-89947 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E516-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE
5、A 5962-89947 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case o
6、utlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 89947 01 M E A Federal stock class designato
7、r RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate
8、 RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic
9、 number Circuit function 01 54HCT4040 12-stage ripple-carry binary counter, TTL compatible inputs 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certificati
10、on to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descr
11、iptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted with
12、out license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89947 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage range (VCC) -0.5 V dc to +7.0 V dc DC input voltage range (VIN) -0.5 V dc to VCC+ 0.
13、5 V dc DC output voltage range (VOUT) . -0.5 V dc to VCC+ 0.5 V dc Clamp diode current 20 mA DC output current (per pin) 25 mA DC VCCor GND current (per pin) . 50 mA Storage temperature range (TSTG) . -65C to +150C Maximum power dissipation (PD) 2/ . 500 mW Lead temperature (soldering, 10 seconds) +
14、300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) +175C 1.4 Recommended operating conditions. 3/ Supply voltage range (VCC) +4.5 V dc to +5.5 V dc Input voltage range (VIN) 0.0 V dc to VCCOutput voltage range (VOUT) 0.0 V dc to VCCCase operating temperature
15、range (TC) . -55C to +125C Input rise or fall time (tr, tf): VCC= 4.5 V, 5.5 V 0 to 500 ns Minimum clock () pulse width (tw1): TC= +25C, VCC= 4.5 V . 20 ns TC= -55C, +125C, VCC= 4.5 V 30 ns Minimum reset pulse width (tw2): TC= +25C, VCC= 4.5 V . 20 ns TC= -55C, +125C, VCC= 4.5 V 30 ns Minimum MR rem
16、oval time (tREM): TC= +25C, VCC= 4.5 V . 10 ns TC= -55C, +125C, VCC= 4.5 V 15 ns Maximum input pulse frequency (fMAX): TC= +25C, VCC= 4.5 V . 25 MHZ TC= -55C, +125C, VCC= 4.5 V 16 MHz 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the ma
17、ximum levels may degrade performance and affect reliability. 2/ For TC= +100C to +125C, derate linearly at 8 mW/C. 3/ Unless otherwise specified, all voltages are referenced to ground. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIR
18、CUIT DRAWING SIZE A 5962-89947 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the exten
19、t specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method
20、Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dl
21、a.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing
22、in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in
23、the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as s
24、pecified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline(s). The case outline(s) sh
25、all be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Switching waveforms an
26、d test circuit. The switching waveforms and test circuit shall be as specified on figure 4. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as speci
27、fied in table I and shall apply over the full case operating temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89947 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 D
28、SCC FORM 2234 APR 97 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers
29、 PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes
30、 Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for d
31、evice class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device c
32、lass M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply for this drawing s
33、hall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q an
34、d V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime -VA of change of product (see 6.2 herein) invol
35、ving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritime s agent, and the acquiring activity retain the option to review the manufacturers facility and
36、applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 40 (see MIL-PRF-38535, appendix A). Pro
37、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89947 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol T
38、est conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max High level output voltage VOHVIN= VIH= 2.0 V, or VIL= 0.8 V IOH= -20 A 1, 2, 3 All 4.4 V IOH= -4 mA 3.7 Low level output voltage VOLVIN= VIH= 2.0 V, or VIL= 0.8 V IOL= +20 A 1, 2, 3 All 0.1 V
39、 IOL= +4 mA 0.4 High level input voltage VIHVCC= 4.5 V 2/ 1, 2, 3 All 2.0 V Low level input voltage VILVCC= 4.5 V 2/ 1, 2, 3 All 0.8 V Quiescent supply current ICCVCC= 5.5 V, VIN= VCCor GND IOUT= 0.0 A 1, 2, 3 All 160 A Input leakage current IINVCC= 5.5 V, VIN= VCCor GND 1, 2, 3 All 1.0 A Additional
40、 quiescent supply current, TTL inputs ICCAny 1 input VIN= 2.4 V or 0.5 V Other inputs VIN= VCCor GND VCC= 5.5 V 1, 2, 3 All 3.0 mA Input capacitance CINVIN= 0 V, see 4.4.1c 4 All 10 pF Power dissipation capacitance 3/ CPDSee 4.4.1c 4 All 57 pF Functional tests See 4.4.1b 7, 8 All Propagation delay t
41、ime, to Q1 output tPHL1, tPLH1VCC= 4.5 V CL= 50 pF See figure 4 9 All 40 ns 10, 11 60 Propagation delay time, Qn to Qn+1 4/ tPHL2, tPLH29 All 15 ns 10, 11 22 Propagation delay time, MR to Qn tPHL39 All 40 ns 10, 11 60 Transition time 4/ tTHL, tTLH9 All 15 ns 10, 11 22 1/ For a power supply of 5.0 V
42、10%, the worst case output voltages (VOHand VOL) occur for HCT at VCC= 4.5 V. Thus, the 4.5 V values should be used when designing with this supply. Worst cases VIHand VILoccur at VCC= 5.5 V and 4.5 V, respectively. 2/ Test are not required if applied as a forcing function for VOHor VOLtests. 3/ Pow
43、er dissipation capacitance (CPD) determines the dynamic power consumption (PD) and the dynamic current consumption (IS): PD(total) = (CPD+ CL) VCC2f + (VCCx ICC) + (n x d x ICCx VCC) IS= (CPD+ CL) VCCf + ICC+ (n x d x ICC) f is input switching frequency; n is number of inputs switching; d is duty cy
44、cle; CLis load capacitance on each output. 4/ This parameter, if not tested, shall be guaranteed to the limits specified in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89947 DLA LAND AND MARITIME
45、 COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 Device type All Case outline E Terminal number Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Q12 Q6 Q5 Q7 Q4 Q3 Q2 GND Q1 MR Q9 Q8 Q10 Q11 VCCFIGURE 1. Terminal connections. Inputs Output state MR L No change L Advanc
46、e to next state X H All outputs are low H = High voltage level L = Low voltage level X = Irrelevant = Low-to-high clock transition = High-to-low clock transition FIGURE 2. Truth table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIR
47、CUIT DRAWING SIZE A 5962-89947 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 FIGURE 3. Logic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89947 DLA
48、 LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 FIGURE 3. Logic diagram Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89947 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 10 DSCC FORM 2234 APR 97 NOTES: 1. CL = 50 pF minimum or equivalent (includes test
