1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Change input to output voltage differential in 1.3, 1.4, VREF, VRLINE, IADJ, and IADJconditions. Change ILIMtest limits for conditions (VIN VOUT) = 2.5 V from 0.05 A to 0.075 A. Add case outline Y (TO-39). 92-08-19 M. A. FRYE B Changes in accorda
2、nce with NOR 5962-R034-94. 92-12-23 M. A. FRYE C Add case outline Z. Technical and editorial changes throughout. 94-08-09 M. A. FRYE D Changes in accordance with NOR 5962-R044-99. 99-03-24 R. MONNIN E Add case outlines M and T. - ro 02-02-21 R. MONNIN F Remove max limits for the current limit test,
3、ILIM, in table I. -rrp 07-07-23 ROBERT M. HEBER THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHET REV SHET REV STATUS REV F F F F F F F F F F F F F F OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY JOSEPH A. KERBY DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICRO
4、CIRCUIT DRAWING CHECKED BY CHARLES E. BESORE COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, POSITIVE REGULATOR, ADJUSTABLE, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING AP
5、PROVAL DATE 90-07-24 AMSC N/A REVISION LEVEL F SIZE A CAGE CODE 67268 5962-89981 SHEET 1 OF 14 DSCC FORM 2233 APR 97 5962-E512-07 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89981 DEFENSE SUPPLY CENTER CO
6、LUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The comple
7、te PIN is as shown in the following example: 5962-89981 01 U X Drawing number Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 LT1086 / OM1860 Positi
8、ve regulator, adjustable 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style M See figure 1 3 Flange mount, glass sealed with gull wing leads T CBCC1-N3 3 Bottom terminal chip carrier U See figure
9、1 3 TO-257 Single row flange mount with isolated tab and glass sealed X See figure 1 2 TO-3 Flange mount Y See figure 1 3 TO-39 Can Z See figure 1 3 Z-tab 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Input to output voltage differenti
10、al . 25 V dc Output current (IMAX): Cases M, T, X, U, and Z . 1.0 A Case Y 0.5 A Power dissipation (PD) . Internally limited Junction temperature (TJ) +150C Storage temperature range -65C to +150C Lead temperature (soldering, 10 seconds). +300C Thermal resistance, junction-to-case (JC): Case M 7.1C/
11、W Case T . 4.1C/W Case X . 3.0C/W Cases U and Z . 4.2C/W Case Y . 40C/W Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89981 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 3
12、DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings Continued. Thermal resistance, junction-to-ambient (JA): Case M 60C/W Case T . 80C/W Case X . 35C/W Cases U and Z . 42C/W Case Y . 140C/W 1.4 Recommended operating conditions. Input to output voltage differential . 15 V dc Ambient operating temperat
13、ure range (TA) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in
14、the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEP
15、ARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 7
16、00 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations
17、 unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manuf
18、acturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535.
19、This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accorda
20、nce with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outline. The case outline shall be in accord
21、ance with 1.2.2 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89981 DEFENSE SUPPLY CENTER COLUMBU
22、S COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 4 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Reference voltage VREFIOUT= 10 mA, (VIN VOUT) = 3.0 V 1 01
23、1.238 1.262 V 1.5 V (VIN VOUT) 15 V, 2/ 1,2,3 1.225 1.270 10 mA IOUT IMAX1.5 V (VIN VOUT) 15 V, 3/ 1.220 1.270 10 mA IOUT IMAXLine regulation 4/ VRLINE1.5 V (VIN VOUT) 15 V, 1,2,3 01 0.2 % IOUT= 10 mA Load regulation 4/ VRLOAD(VIN VOUT) = 3.0 V, 2/ 1 01 0.3 % 10 mA IOUT IMAX2,3 0.4 (VIN VOUT) = 3.0
24、V, 3/ 1 0.8 10 mA IOUT IMAX2,3 1.0 Dropout voltage VDOIOUT= IMAX, VREF= 1.0 % 1,2,3 01 1.5 V Thermal regulation - 30 ms pulse, TA= +25C 1 01 0.04 %/W Ripple rejection VIN/ VOUTCADJ= 25 F, f = 120 Hz, COUT= 25 F (tantalum), IOUT= IMAX, (VIN VOUT) = 3.0 V 4,5,6 01 60 dB Adjust pin current IADJ1.5 V (V
25、IN VOUT) 15 V, 10 mA IOUT IMAX1,2,3 01 120 A Adjust pin current change IADJ10 mA IOUT IMAX, 1.5 V (VIN VOUT) 15 V 1,2,3 01 5.0 A See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-
26、89981 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Minimum load c
27、urrent IMIN(VIN VOUT) = 25 V 1,2,3 01 10 mA Current limit ILIM(VIN VOUT) = 5.0 V, case X only 1,2,3 01 1.5 A (VIN VOUT) = 5.0 V 3/ 1.5 (VIN VOUT) = 5.0 V, case Y only 0.5 (VIN VOUT) = 25 V, case X only 0.05 (VIN VOUT) = 25 V 3/ 0.075 (VIN VOUT) = 25 V, case Y only 0.02 Temperature stability 5/ VOUT/
28、 T -55C TJ +125C 1,2,3 01 1.5 % Long term stability 5/ VOUT/ t TA= +125C, t = 1000 hrs. 2 01 1.0 % 1/ For case outlines, M, T, X, U, and Z, IMAX= 1.0 A. For case outline Y, IMAX= 0.5 A. 2/ Applies to cases X and Y. 3/ Applies to cases M, T, U, and Z. 4/ Line and load regulation are measured at a con
29、stant junction temperature using a low duty cycle pulse technique. Although power dissipation is internally limited, regulation is guaranteed up to the maximum power dissipation of 15 W. Power dissipation is determined by the input/output differential voltage and the output current. Guaranteed maxim
30、um power dissipation will not be available over the full input/output voltage range. 5/ If not tested, shall be guaranteed to the limits specified in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-8
31、9981 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 6 DSCC FORM 2234 APR 97 Case outline M Symbol Inches Millimeters Min Max Min Max A .190 .210 4.83 5.33 b - .030 - 0.76 D .410 .430 10.41 10.92 D1 .580 .610 14.73 15.49 e - .100 - 2.54 e1 - .200 - 5.08 E .410 .420 10
32、.41 10.67 L1 .090 .110 2.29 2.79 L .115 .125 2.92 3.18 N 3 3 NOTE: The U.S. government preferred system of measurement is the metric SI system. However, since this item was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, th
33、e inch-pound units shall take precedence. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89981 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 7 DSCC F
34、ORM 2234 APR 97 Case outline U Inches mm .005 0.13 Letter Inches Millimeters Min Max Min Max A .190 .200 4.83 5.08 A1.035 .045 0.89 1.14 A2.120 BSC 3.05 BSC b .025 .035 0.64 0.89 D .645 .665 16.38 16.89 D1.410 .430 10.41 10.92 D3- .065 - 1.65 e .100 BSC 2.54 BSC E .410 .422 10.41 10.72 L .500 .750 1
35、2.70 19.05 O .527 .537 13.39 13.64 P .140 .150 3.56 3.81 NOTE: The U.S. government preferred system of measurement is the metric SI system. However, since this item was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the in
36、ch-pound units shall take precedence. FIGURE 1. Case outline Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89981 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 8
37、DSCC FORM 2234 APR 97 Case outline X Letter Inches Millimeters Min Max Min Max A .250 .450 6.35 11.43 b .038 .043 .97 1.09 D - .875 - 22.23 e .420 .440 10.67 11.18 e1.205 .225 5.21 5.72 F1.060 .135 1.52 2.43 L .312 .500 7.92 12.70 L1- .050 - 1.27 p .151 .161 3.84 4.09 q 1.177 1.197 29.90 30.40 R .49
38、5 .525 12.57 13.34 R1.131 .188 3.33 4.78 S .655 .675 16.64 17.15 NOTE: The US government preferred system of measurement is the metric SI system. However, since this item was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units,
39、the inch-pound units shall take precedence. FIGURE 1. Case outline Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89981 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SH
40、EET 9 DSCC FORM 2234 APR 97 Case outline Y Letter Inches Millimeters Min Max Min Max A .165 .185 6.35 11.43 b1 .016 .019 0.97 1.09 D .340 .370 8.64 22.23 D1 .305 .335 4.10 1.09 e .200 typ NOTE 2 5.08 typ NOTE 2 e1 .100 typ NOTE 2 2.54 typ NOTE 2 k .028 .038 0.71 0.97 k1 .026 .045 0.66 1.27 L .500 -
41、12.70 - NOTES: 1. The US government preferred system of measurement is the metric SI system. However, since this item was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. 2. Leads
42、having a maximum diameter of .019 inch (0.48 mm) measured in gauging plane .054 inch .001 inch (1.37 mm 0.03 mm) below the base plane of the product shall be within .007 inch (0.18 mm) of their true position relative to the maximum width tab. FIGURE 1. Case outline Continued. Provided by IHSNot for
43、ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89981 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 10 DSCC FORM 2234 APR 97 Case outline Z Letter Inches Millimeters Min Max Min Max A .910 .920 23.
44、11 23.37 A1.410 .420 10.41 10.67 A2.245 .255 6.22 6.48 A3.120 .130 3.05 3.30 b .120 .130 3.05 3.30 D .135 .220 4.70 5.59 D1.115 .125 2.92 3.18 D2.035 .045 0.89 1.14 e .100 BSC 2.54 BSC L .410 .420 10.41 10.67 L1.500 .750 12.70 19.05 L2 .245 .255 6.22 6.48 L3 .120 .130 3.05 3.30 p .028 .032 0.71 0.81
45、 NOTES: The US government preferred system of measurement is the metric SI system. However, since this item was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. FIGURE 1. Case outl
46、ine Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89981 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 11 DSCC FORM 2234 APR 97 Device type 01 Case outlines M T T
47、erminal number Terminal symbol 1 ADJUST ADJUST 2 OUTPUT INPUT3 INPUT OUTPUT FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89981 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 12 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electr
