1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update boilerplate paragraphs to current MIL-PRF-38535 requirements. - ro 11-08-16 C. SAFFLE REV SHET REV SHET REV STATUS REV A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY RICK C. OFFICER DLA LAND AND MARITIME COLUMBUS,
2、 OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY CHARLES E. BESORE APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, LOW POWER BUFFER AMPLIFIER, MONOLITHIC SILICO
3、N DRAWING APPROVAL DATE 93-01-20 AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-90509 SHEET 1 OF 9 DSCC FORM 2233 APR 97 5962-E259-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90509 DLA LAND AND
4、MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The comp
5、lete PIN is as shown in the following example: 5962-90509 01 P A Drawing number Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 EL2002A Low power bu
6、ffer amplifier 02 EL2002 Low power buffer amplifier 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style P GDIP1-T8 or CDIP2-T8 8 Dual-in-line 2 CQCC1-N20 20 Square leadless chip carrier 1.2.3 Lead
7、finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Total supply voltage ( +VSto VS) . 36 V Supply voltage ( VS) . 18 V dc Input voltage ( VIN) 15 V dc or VS1/ Input current ( IIN) 50 mA 1/ Output short circuit duration Continuous 2/ Junction temperatu
8、re (TJ) . +175C Storage temperature range . -65C to +150C Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 3/ Thermal resistance, junction-to-ambient (JA) : 3/ Case P . +125C/W Case 2 . +100C/W _ 1/ If the input exceeds the ratings shown (or
9、 the supplies), or if the input to the output voltage exceeds 7.5 V, then the input current must be limited to 50 mA. 2/ A heat sinking is required to keep the junction temperature below the absolute maximum when the output is short circuited. 3/ The maximum power dissipation depends on package type
10、, ambient temperature, and heat sinking. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90509 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.4 Recommended op
11、erating conditions. Supply voltage ( VS) . 15 V dc Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein
12、. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcirc
13、uits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/
14、 or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document,
15、however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to
16、 this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying a
17、ctivity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described h
18、erein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.
19、1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specif
20、ied in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. Provided by IHSNot for ResaleNo reproduc
21、tion or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90509 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA+125C Group A subgro
22、upsDevice type Limits 1/ Unit VS= 15 V, RS= 50 unless otherwise specified Min Max Offset voltage VOSVIN= 0 V, RL= 1 01 -15 +15 mV 2,3 -20 +20 1 02 -40 +40 2,3 -50 +50 Input current IINVIN= 0 V, RL= 1 01 -10 +10 A 2,3 -15 +15 1 02 -15 +15 2,3 -20 +20 Input resistance RINVIN= 12 V, RL= 100 1 All 1 M 2
23、,3 0.1Voltage gain AV1VIN= 12 V, RL= 1 All 0.990 V/V 2,3 0.985AV2VIN= 10 V, RL= 100 1 0.85 2,3 0.83AV3VIN= 3 V, RL= 100 , 1 0.83 VS= 5 V 2,3 0.80 Output voltage swing +VOVIN= +12 V, RL= 100 1 All +10 V 2,3 +9.5 -VOVIN= -12 V, RL= 100 1 -10 2,3 -9.5 Output resistance ROUTVIN= 2 V, RL= 100 1 All 13 2,
24、3 15Output current +IOUTVIN= +12 V, VOUT= +10 V 1 All +100 mA 2,3 +95 -IOUTVIN= -12 V, VOUT= -10 V 1 -100 2,3 -95 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90509 DLA LAND
25、AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TA+125C Group A subgroupsDevice type Limits 1/ Unit VS= 15 V, RS= 50 unless otherwise specified Min Max Supply current ISVIN=
26、 0 V, RL= 1 All 7.5 mA 2,3 10Power supply rejection ratio PSRR VIN= 0 V, RL= 2/ 1 All 60 dB 2,3 50Slew rate +SR VIN= 10 V, RL= 100 , 3/ 4/ 4 All 1200 V/s AV= +1, CL= 10 pF, rising edge 5,6 800 -SR VIN= 10 V, RL= 100 , 3/ 4/ 4 1200 AV= +1, CL= 10 pF, falling edge 5,6 800 -3 dB bandwidth VOUT= 10 mV,
27、RL= 100 , 4/ CL= 0 pF 4,5,6 All 90 MHz Rise time trVIN= 5 V, RL= 100 , 4/ TA= +25C 9 All 4.0 ns Propagation delay tdVIN= 5 V, RL= 100 , 4/ TA= +25C 9 All 4.0 ns 1/ The algebraic convention, whereby the most negative value is a minimum and the most positive is a maximum, is used in this table. Negati
28、ve current shall be defined as conventional current flow out of a device terminal. 2/ VOSis measured at +VS= 4.5 V, -VS= -4.5 V, and at +VS= +18 V, -VS= -18 V. Both supplies are changed simultaneously. 3/ Slew rate is measured between VOUT= +5 and -5 V. 4/ If not tested, shall be guaranteed to the l
29、imits specified in table I herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90509 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 Device types 01 and 02 C
30、ase outlines P 2 Terminal number Terminal symbol 1 +VSNC 2 INPUT+VS3 NC NC4 -VSNC 5 NC NC6 NC NC 7 OUTPUT NC 8 NC NC9 - NC 10 - INPUT 11 - NC 12 - -VS13 - NC 14 - NC 15 - NC 16 - NC 17 - NC 18 - NC 19 - NC 20 - OUTPUT NC = No connection FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo
31、 reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90509 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall
32、 be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/complia
33、nce mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certi
34、ficate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply shall
35、affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8
36、 Notification of change. Notification of change to DLA Land and Maritime -VA shall be required for any change that affects this drawing. 3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility
37、 and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in ac
38、cordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufactu
39、rer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA=
40、+125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4.3 Quality conformance inspection. Quality conformance inspection shall be in acco
41、rdance with method 5005 of MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 7, 8, 10, and 11 in table I, method 5005 of MIL-STD-883 shall be omitted. Provi
42、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90509 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 8 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-STD-883 test require
43、ments Subgroups (in accordance with MIL-STD-883, method 5005, table I) Interim electrical parameters (method 5004) - Final electrical test parameters (method 5004) 1*,2,3 Group A test requirements (method 5005) 1,2,3,4*,5*,6*,9* Groups C and D end-point electrical parameters (method 5005) 1,2,3 * PD
44、A applies to subgroup 1. * Subgroups 4, 5, 6, and 9 are guaranteed, if not tested, to the limits specified in table I herein. 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-88
45、3. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as a
46、pplicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TA= +125C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-385
47、35, appendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic
48、 device covered by a contractor-prepared specification or drawing. 6.3 Configuration control of SMDs. All proposed changes to existing SMDs will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90509 DLA LAND AND MARITIME
