1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Technical changes to table I. Editorial changes throughout. 91-12-23 M. L. Poelking B Update boilerplate to MIL-PRF-38535 requirements. - CFS 03-08-04 Thomas M. Hess C Update boilerplate to current MIL-PRF-38535 requirements. - CFS 08-07-16 Thoma
2、s M. Hess REV SHET REV C C SHET 15 16 REV STATUS REV C C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Tim H. Noh DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Tim H. Noh COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS D
3、RAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY William K. Heckman MICROCIRCUIT, DIGITAL, CMOS, UNIVERSAL ASYNCHRONOUS RECEIVER TRANSMITTER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 91-02-05 MONOLITHIC SILICON AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-905
4、25 SHEET 1 OF 16 DSCC FORM 2233 APR 97 5962-E382-08 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90525 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 9
5、7 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When av
6、ailable, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example. 5962 - 90525 01 M Q X Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead f
7、inish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels a
8、nd are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function Clock frequency (fclk) 01 HD-6402R Universal asynchronous receiver transmitter (UAR
9、T) 2.0 MHz 02 HD-6402B Universal asynchronous receiver transmitter (UART) 8.0 MHz 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requir
10、ements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designato
11、r Terminals Package style Q GDIP1-T40 or CDIP2-T40 40 Dual-in-line 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from
12、 IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90525 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage +8.0 V Input, output, or I/O voltage applied . GND 0.5 V dc to VCC+0.5 V dc Junction temper
13、ature (TJ). +175C Storage temperature range -65C to +150C Lead temperature (soldering, 10 seconds). +300C Power dissipation (PD) 1.03 W Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA) 48.3C/W 1.4 Recommended operating conditions. Supply volta
14、ge (VCC) +4.5 V dc to +5.5 V dc Case operating temperature range (TC) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise spe
15、cified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - I
16、nterface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardiz
17、ation Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes app
18、licable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction
19、or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90525 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q an
20、d V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be
21、 in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535,
22、 appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Control definition. The control definition shall be as specified on figure 2. 3.2.
23、4 Block diagram. The block diagram shall be as specified on figure 3. 3.2.5 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 4. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified he
24、rein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The elect
25、rical tests for each subgroup are described in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer h
26、as the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 C
27、ertification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certifica
28、te of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-1
29、03 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requireme
30、nts of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notific
31、ation of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent
32、, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by th
33、is drawing shall be in microcircuit group number 105 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90525 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LE
34、VEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Input high voltage VIHVCC= 5.5 V 1, 2, 3 All 2.3 V Input low voltage VILVCC= 4.5 V 1, 2, 3 All 0.8
35、 V Input leakage current IIVO= 0 V or 5.5 V, VCC= 5.5 V 1, 2, 3 All -1.0 1.0 A IOH= -2.5 mA, VCC= 4.5 V 2/ 3.0 Output high voltage VOHIOH= -100 A, VCC= 4.5 V 2/ 1, 2, 3 All VCC 0.4 V Output low voltage VOLIOL= +2.5 mA, VCC= 4.5 V 2/ 1, 2, 3 All 0.4 V Output leakage current IOVO= 0 V or 5.5 V, VCC= 5
36、.5 V 1, 2, 3 All -1.0 1.0 A Operating supply current ICC3/ VO= 0 V or 5.5 V, VCC= 5.5 V, fclk= 2.0 MHz, Outputs open 1, 2, 3 All 2.0 mA Standby supply current ISBVO= 0 V or 5.5 V, VCC= 5.5 V, Outputs open 1, 2, 3 All 100 A Input capacitance CIN4 All 25 pF Output capacitance COUTAll measurements are
37、referenced to device GND, f = 1.0 MHz, TA= +125C, See 4.4.1c 4 All 25 pF Functional tests See 4.4.1b 7, 8 All See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90525 DEFENSE SUPPL
38、Y CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max 01 2.0 Clock frequency fCLK9, 1
39、0, 11 02 8.0 MHz 01 150 CRL, DRR, and TBRL pulse width tPW9, 10, 11 02 75 ns Pulse width MR tMR9, 10, 11 All 150 ns 01 50 Input data setup time tSET9, 10, 11 02 20 ns 01 60 Input data hold time tHOLD9, 10, 11 02 20 ns 01 160 Output enable time tENSee figure 4. CL = 50 pF, VCC= 4.5 V tr= tf= 1.0 ns/V
40、 9, 10, 11 02 35 ns 1/ All tests shall be performed using the worst case conditions, unless otherwise specified. 2/ Interchanging of force and sense conditions is permitted. Relaxed input levels for VOLand VOHmay be used if separate VILand VIHtests that guarantee threshold voltage transition are per
41、formed. 3/ If not tested, shall be guaranteed to the limits specified in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90525 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL
42、C SHEET 7 DSCC FORM 2234 APR 97 Device types: 01 and 02 Case outline Q Terminal number Terminal symbol Terminal number Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 VCCNC GND RRD RBR8 RBR7 RBR6 RBR5 RBR4 RBR3 RBR2 RBR1 PE FE OE SFD RRC DRR DR RRI 21 22 23 24 25 26 27 28 29 30 31
43、 32 33 34 35 36 37 38 39 40 MR TBRE TBRL TRE TRO TBR1 TBR2 TBR3 TBR4 TBR5 TBR6 TBR7 TBR8 CRL PI SBS CLS2 CLS1 EPE TRC NC = No connection FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZ
44、E A 5962-90525 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Control word Character format CLS2 CLS1 PI EPE SBS START BIT DATA BITS PARITY BIT STOP BITS 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1
45、 1 1 1 0 0 0 0 1 1 0 0 0 0 1 1 0 0 0 0 1 1 0 0 0 0 1 1 0 0 1 1 X X 0 0 1 1 X X 0 0 1 1 X X 0 0 1 1 X X 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 5 5 5 5 5 5 6 6 6 6 6 6 7 7 7 7 7 7 8 8 8 8 8 8 ODD ODD EVEN EVEN NONE NONE ODD ODD EVEN EVEN NONE NO
46、NE ODD ODD EVEN EVEN NONE NONE ODD ODD EVEN EVEN NONE NONE 1 1.5 1 1.5 1 1.5 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 X = Irrelevant 0 = Low level voltage 1 = High level voltage FIGURE 2. Control definition. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,
47、-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90525 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 9 DSCC FORM 2234 APR 97 Note: These outputs are three-state. FIGURE 3. Block diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license
48、from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90525 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 10 DSCC FORM 2234 APR 97 Note: CLincludes stray and jig capacitance. FIGURE 4. Switching waveforms and test circuit. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90525 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SH
