1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R185-93. 93-06-11 Michael FryeB Changes in accordance with NOR 5962-R014-97. 96-10-08 Ray Monnin C Made changes to forward voltage drop and leakage current test in table I. Revised source to reflect cage 01295.
2、 Updated boilerplate. -lgt 01-06-13 Ray Monnin D Update boilerplate for device class V. - gt 03-06-11 Ray Monnin THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHET REV SHET REV STATUS REV D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 PMIC N/A PREPARED BY Joseph A. Kirby DEFENSE S
3、UPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Charles E. Besore COLUMBUS, OHIO 43216 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Michael A. Frye MICROCIRCUIT, LINEAR, QUAD SCHOTTKY DIODE ARRAY, MONOLITHIC SILICON AND AGENCIES OF THE DEPART
4、MENT OF DEFENSE DRAWING APPROVAL DATE 90-11-06 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-90538 SHEET 1 OF 8 DSCC FORM 2233 APR 97 5962-E511-02 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permi
5、tted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90838 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (devi
6、ce classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as show
7、n in the following examples. For device classes M and Q: 5962 - 90538 01 P X Federal stock class designator RHA designator (see 1.2.1) Devicetype (see 1.2.2) Caseoutline (see 1.2.4) Lead finish (see 1.2.5) / / Drawing number For device class V: 5962 - 90538 01 V P X Federal stock class designator RH
8、A designator (see 1.2.1) Devicetype (see 1.2.2) Deviceclass designator Caseoutline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA de
9、signator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number
10、 Circuit function 01 UC1611 Quad schottky diode array, 1 amp 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as listed below. Since the device class designator has been added after the original issuance of this drawing, device cla
11、sses M and Q designators will not be included in the PIN and will not be marked on the device. Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q
12、or V Certification and qualification to MIL-PRF-38535 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90838 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR
13、 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style P GDIP1-T8 or CDIP2-T8 8 Dual-in-line 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-P
14、RF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. 1.3 Absolute maximum ratings. 1/ Peak inverse voltage (per diode). 45 V dc Diode-to-diode voltage. 75 V dc Peak forward current . 1 A Power dissipation (PD) . 1 W 2/ Lead temperature (soldering, 10 seconds) +300C Th
15、ermal resistance, junction-to-case (JC) See MIL-STD-1835 Junction temperature (TJ) 150C 1.4 Recommended operating conditions. Ambient operating temperature range (TA) -55C TA +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards,
16、 and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation. SPECIFICAT
17、ION DEPARTMENT OF DEFENSE MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. HANDBOOKS DEPARTMENT OF DEFENSE MIL-HDBK-10
18、3 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 1/
19、Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Derate at 8.0 mW/C for TAabove +25C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license f
20、rom IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90838 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this d
21、rawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as sp
22、ecified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-J
23、AN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case o
24、utline(s). The case outline(s) shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performa
25、nce characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgr
26、oup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked as listed in MIL-HDBK-103. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has
27、 the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Cer
28、tification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate
29、 of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103
30、 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirement
31、s of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notificat
32、ion of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change as defined in MIL-PRF-38535, appendix A. 3.9 Verification and review for device class M. For device class M, DSCC,
33、 DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices c
34、overed by this drawing shall be in microcircuit group number 110 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90838 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
35、 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Forward voltage drop VFIF= 100 mA 1 01 0.7 V IF= 1.0 A 1/ 1.2 Leakage current ILVR= 40 V
36、1 01 0.1 mA 2 1.5 1/ At forward currents of greater than 1.0 A, a parasitic current of approximately 10 mA may be collected by adjacent diodes. 4. QUALITY ASSURANCE PROVISIONS 4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with MIL-
37、PRF-38535 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. For device class M, sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screen
38、ing. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and shall be conducted on all devices prior to qualification and technology conformance inspection. For device class M, screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on al
39、l devices prior to quality conformance inspection. 4.2.1 Additional criteria for device class M. a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available t
40、o the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1015. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as speci
41、fied in table II herein. 4.2.2 Additional criteria for device classes Q and V. a. The burn-in test duration, test condition and test temperature, or approved alternatives shall be as specified in the device manufacturers QM plan in accordance with MIL-PRF-38535. The burn-in test circuit shall be mai
42、ntained under document revision level control of the device manufacturers Technology Review Board (TRB) in accordance with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation,
43、 as applicable, in accordance with the intent specified in test method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein. c. Additional screening for device class V beyond the requirements of device class Q shall be as specified in MIL-PRF-
44、38535, appendix B. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90838 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 Device type 01 Case outlines P
45、2 Terminal number Terminal symbol Terminal symbol 1 C1 NC 2 A1 A1 3 A2 NC 4 C2 NC 5 C3 A2 6 A3 NC 7 A4 C2 8 C4 NC 9 - - - NC 10 - - - C3 11 - - - NC 12 - - - A3 13 - - - NC 14 - - - NC 15 - - - A4 16 - - - NC 17 - - - C4 18 - - - NC 19 - - - NC 20 - - - C1 NC = No connections. FIGURE 1. Terminal con
46、nections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90838 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements.
47、Test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Subgroups (in accordance with MIL-PRF-38535, table III) Device class M Device class Q Device class V Interim electrical parameters (see 4.2) - - - Final electrical parameters (see 4.2) 1, 2, 3 1/ 1, 2, 3 1/ 1, 2, 3 1/
48、 Group A test requirements (see 4.4) 1, 2, 3 1, 2, 3 1, 2, 3 Group C end-point electrical parameters (see 4.4) 1, 2, 3 1, 2, 3 1, 2, 3 Group D end-point electrical parameters (see 4.4) 1, 2, 3 1, 2, 3 1, 2, 3 Group E end-point electrical parameters (see 4.4) - - - 1/ PDA applies to subgroup 1. 4.3 Qualification inspection for device classes Q and V. Qualification inspection for device classes Q and V shall be in accordance with MIL-PRF-38535. Inspections to be performed shall be those specified in MIL-PRF-38535 an
